AMV6502REW7 Maytag Microwave - Instructions

Husband replaced the bulb

Spouse just screwed in the new bulb and reinstalled the light cover plate with the two screws. Took under a minute. Works great.

Unplug the microwave. Then remove the six screws that hold the lower panel which has the light bulb cover and a couple of vent filters. The light bulb sockets are on a fixture that is connected by a quick connect electrical connector. Disconnect that and the whole panel is free to access the bulbs. My bulbs were very fragile and trying to twist them out resulted in the glass twisitng loose with the base still in the sockets. I needed to use a needle nose pliers to remove the bases and then I replaced the bulbs and put every thing back together

Repair unsuccessful because they sent the wrong part, even after I questioned their selection. It is amazing how a company as large as Whirlpool cannot clearly indicate to the people who work for them how to order the correct part. The fault lies not in the individual who is putting the order in but with the company who cannot take the time to make sure that person is successful in completing their job. Will never buy a product from this company again.
As far as the shipping is concerned. It took forever, just to find out that the part was incorrect.
Better luck next time. right?

Removed the old turntable tray, replaced it with the new one.

removed perimeter screws from the bottom side and the lower cover is hinged at the wall side. Motor is visible and easily removed with two screws. Take of the old one, install the new one, and reverse the procedure to put the bottom cover back in place. Will nee helper to hold one side of the bottom until couple of screws can be put in on the other side.

I removed the old base by unscrewing the12 screws and dropping down the metal bottom. I disconnected the light and unclipped the electrical wiring harness for the fan and removed the bottom base. I then reattached the wiring harness and light to the new base and reattached the base to the microwave with the 12 screws. It is now as good as new again!! Thank you for locating this hard to find part for me!

took it out of box wooolaaa fixed thanks fast shipping too...

On top front of the microwave are two Philip's head screws holding the rail on. Remove these screws and the rail snap out the old filter (noting the dark side down) then snapping the new filter in. Replace rail. 10 to 15 minute task.

Ordered a new motor. Removed the outside trim of the oven-microwave combo. 2 screws at the bottom of the trim. Removed the screws that held the combination micro and oven unit in place. Removed the top and bottom black plastic grill of the microwave. 3 screws each. Pulled the entire unit out about 1 inch exposing the screws at each side of the microwave that hold it in place.
Snapped off the top control panel which exposed the wiring connecting the control panel.
Unplugged a couple of wire harness units to free the control panel.
Be sure to label the units to know which goes where during reassembly.
Remove the microwave unit from the housing and place it on its side.
Remove the metal plate that houses the motor. 4 screws hold the motor in place. Disconnect the 2 wires from the old motor and you are ready to install the new motor. Be sure to TURN OFF THE POWER to the unit at the breaker box and remove the turntable from inside the microwave.

I removed the microwave to install a back splash and found the support edge on the backplate had broken off and was missing. I searched for parts for the microwave and found them on PartsSelect.com. Easy to order, and was shipped promptly.

Once the part arrived, install was simple, lining up the existing holes. The only hard part was setting the microwave up on the bracket due to the weight and awkwardness of the microwave.

Overall a very simple repair.

After removing the over-the-range unit (no small feat!) I had to figure out how to open the case (good puzzle!). Capacitor had already discharged, so it was very easy to reach in, pop the old fuse and install the new one! As per your advice, I found out I was a "28%-er"! Upon re-installation, the microwave "sprang to life"!! Thanks, "Part Select"!! I was already shopping around for a new machine! (Now if you could only tell me an easier way to re-mount this heavy beast over the stove!!!)

Unscrewed glass panel, removed old bulb, cleaned glass panel and installed new bulb. Screwed panel back into place.

Removed the face plate above the door (2 Phillips screws.) Removed existing filter and replaced with the new one purchased. Reinstalled the face plate.

when I opened the back cover of microwave, the diode was kind of blackish blown, since there was light bulb and fan were still working, i thought it could be problem with any one of the components like; magnatron or capacitor or diode, so first replaced the diode and mica at the end of the magnatron duct, there was problem with door switch as well. i fixed that too. Now it is working. It cooks bit faster, Wondering why?