ALW450QAC Amana Washer - Instructions

Basically you have to remove the drive motor and pump (in that order). This allows you to get the belt around the drive motor pully wheel. It took me a few tries to get the belt routed right. I assume that if you know what you are doing you can complete this in under an hour. It took me about 4 hours, though - cause I didn't know what I was doing at first. Hehe.

Hope this helps.

Replaced the mixing value using the kit purchased from PartSelect. The instructions with the kit plus the installation tips found on their WEB Page were extremely helpful. Everything went as predicted except I had to cut and insert a new piece of wire on the white wire between the hot and cold electrical connections. I used two crimp connectors to lengthen the wire. This was a very simple job for a 73 year old man like me. Thank you for the tips and quick delivery of the mixer value kit.

removed both hot and cold fill lines and front of washer panel. removed screw holding mix valve plate t the back of the washer . Unpluged connections to mix valve and replaced valve. ( note removing the top of the washer is needed and can only be done by first removing the front by sliding a thin screw driver between the top and front panel to release the clips at the ends.)

Removed spring, then hoses and then belts. When all was removed we loosen the old washer pump and installed the new pump. Everything was re-installed and was put to wash. At first it leaked water that was already sitting there, but then it work like new. Oh I also read the instruction on this website, I recommend the site to everyone!!

Followed video on PartsSelect website, they made it real easy.

Removed old hose by sqeezing clamps and sliding off of fittings. Placed clamps on new hose. Slid hose on fittings. Repositioned clamps over end of hose. Job done.

Removed front lower panel, removed 4 bolts holding motor, removed water hoses draining water into a pot, unplugged electrical connector on motor, removed motor, removed water pump from motor (torex bit), separated pump from motor. installed belt reassembled washer in reverse order. To my surprise, it worked and was easy.

We promptly received the part and easily installed it with no tools. We had an excellent experience. We found the old fabric softener dispenser after installing the new one. Now, we have two.

First, I removed the screws, then removed the pump. I, then, installed a new pump.

I ordered my part on Monday. It was delivered on Tuesday, and by four o'clock we were in business. I highly reccomend PartSelect.

disconnected valve replaced with new, real easy. I removed motor and belt ,4 bolts, than removed 3 star screws from pump, replaced pump and replaced unit. Worked great!!!
Delivery of parts was faster than promised, standard shipping.

tilt the washer back removed bottom panal .removed bracket holding motor took motor out removed 3 scewer holding pump. took belt off put new one on. about 45 mins pretty easy job

Remove 3 screws on Washer control top. Then 3 screws holding clear cover and removed. Remove 3 phillips screws holding face of panel on and tilted panel to get at wires. Marked the wire colors on eace of 4 terminals and removed them. Used plires to push the top on the switch near the knob and turned the switch counterclockwise. When the lugs lined up the switch slid out the back. Just reversed the above to reinstall following the proper colors on the wires to reinstall. Washer works fine now.

Unpluged washer, turned off water supply, removed front covers, removed spring on right side to allow drum to lean over, removed the 2 hoses from pump, removed motor (4 bolts), removed 3 screws holding pump. Installed a new belt and replaced the pump. I replaced the hoses on the pump, replaced the spring, and turned on the water, plugged in the washer, turned it on and hoped for the best. Worked fine, no leaks or problems.

I seemed to have a more difficult time changing the pump out than others who had left their instructions on line prior to me.
What I has to do is remove the 4 bolts that secured the motor & mount to the frame. I then unplugged the wire harness from the motor leads.
I removed the belt tensioning spring & removed the belt.
I then removed the motor, motor mount and pump assembly. Turned it upside down & removed the pump. When installing the new pump you will need to remember how the belt was routed. A local parts house actually gave me a xeroxed schematic that showed me how to route it. A real life saver.
After that I turned the assembly right side up, bolted the mount into place, installed the new belt onto the large flywheel, attached the belt tension spring, plugged in the wiring harness and ran a rinse cycle. No leaks. Good as new.
Yes. It took a little longer than expected. But it was alot cheaper than having a service man do it.