ALW450QAC Amana Washer - Instructions

thought wire between hot and cold valve was to short but after many phone calls found out valve could be ajusted by prying carefully up clips and moving valve closer not in directions

Removed old hose, drained the water from the hose. Put new hose on.

The hardest part was removing the tub from washer by myself. I simply removed the bolts holding the sides to the bottom of the unit and lifted it straight off. Be careful when you remove the springs from the drum so they don't spring back and puncture the drain line. Thank you RTV gasket maker. Once the drum was free from the base, i tilted the drum back exposing the pump housing. I used a pair of pliers to remove both drain lines then removed the 3 hex screws freeing the pump. I had no problem removing it from the motor shaft, it slipped right off. I put everything back together as easily as it came apart.

Removed the tension spring from the belt retention belt, removed the belt from the large pulley in the back of the washer, removed the 4 bolts holding in the motor and washer pump, removed wiring harness, disconnected the inlet and outlet hoses from the pump and pulled out the motor and the washer pump. Turned the motor over and using the Torx driver (#20) removed the 3 bolts holding on the pump. Gently wiggled and pried the washer pump off of the motor, replaced the pump and tightened down the Torx bolts carefully so the pump didn't crack or break it is just plastic, but had to be sure the pump was seated tightly so the pump would fit back into place and also so it wouldn't leak, after making sure it was tightly attached I reversed the process to put it back together.

Although the Maytag website no longer had a repair manual in their database, I was able to locate one fairly easily online. After removing the motor/washer pump, it was easy to remove the 3 screws holding the washer pump to the motor. Unfortunately, it turned out the motor hub shaft had corroded and removing the pump needed some ... persuasion. Patience and a rubber mallet eventually separated the water pump from the motor. Re-installing went quickly and, so far, no leaks and the washing machine has not started walking across the floor.

knife to losen top, remove rear tabs securing top, unplug electical from timer and switches, unplug front door wiring, 2 bolts remove front, lift front pannel to remove. tape belt on drum on top. under drum you can see the belt around worn pulley. lift idler pulley assembly, remove belt from pulley, snap ring holds pulley in place remove woren pulley, install new, replace snap ring, restring belt. remove tape. spin drum to assure alignment. reassemble.

Pretty easy repair ... especially after reading previous owners instructions and experiences. After unplugging unit from power and shutting off water supply - 1) Remove front panel. 2) Remove small tensioner spring. 3) Disconnect power connector to motor. 4) Disconnect two water hoses from pump (place towel underneath to catch water). 5) Remove 4 large bolts holding motor assembly to frame. 6) Slide off spin belt from tub pulley. 7) Remove motor assembly. Pump and belt are attached. 8) Take to workbench. Note orientation of belt wrt pump. 9) Loosen and remove 3 star head screws (I used a drill bit and drill). 10) Slide pump off motor shaft. Mine came off clean and easy. 11) Remove belt. It's good to order the belt with the pump and replace them both. My belt was pretty chewed up and I'm glad I had a replacement. 12) Attach new belt and pump, being mindful of belt route. 13) Re-attach motor assembly, threading belt around large pulley. 14) Attach water hoses and motor connector. 15) Attach belt tensioner spring. Test on a short cycle....if all is well, close it up and you're done. Took me about 45 minutes.

Removed lower front cover--two screws. Removed motor/pump assembly after disconnecting electric and water hoses. Seperated pump from motor. Installed belt, then reconnected pump to motor. Reinstalled motor/pump assembly, while rotating belt onto drum pulley. Reinstalled eclectric and water hoses. Buttoned front cover back up. Done.

After pulling front lower panel off, disconnected idler pulley spring and left side tub stabilizer spring to allow room to get motor out the front. Took belt off transmision pulley, unbolted 4 motor mount bolts, dropped the motor/pump assembly down and disconnected the electrical plug (motor). Took motor/pump assembly out, flipped it over, unbolted 3 pump bolts to remove old pump, which came right off. Then reversed the whole process. Pretty straightforward, just time.

Repair went well using posted instructions. My advice is always replace pump as you will damage seal when pulling pump off shaft.