AG202MB Jenn-Air Range - Instructions

George from Sacramento, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Had no use for the grill wanted 4 burners

Took out grill grates then took out cartridge ...replaced burner cartridge then attached spill pan then burner grates.... super easy
Note:.. center fan will go off AFTER you put drip pan in

Parts Used:

Michelle from CAMBRIA, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

One 25 yr-old burner was beginning to leak gas because of corrossion. Decided to replace all 4 burners.

Remove grates and pan. unscrew each burner from the metal cross mount bar, keeping in mind, the position of the cross mount bar.(Mine was not reversible.) Reverse the procedure with the new burners.
Adjust the air opening to eliminate any yellow flame. The air opening is located immediately adjacent to where the burner pipe goes into the cooktop. (Near the front of the cooktop in my case.)

Biggest problem was making sure the correct parts were ordered.

Parts Used:

Ronald from Poulsbo, WA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

1 person found this instruction helpful.

Was this instruction helpful to you?

Burners would not light. Grates were warped

Ordered the part from you and received it on the third day. Simply unplugged the old assembly and plugged in the new one. Turned the control and the burners lit immediately. It was a piece of cake. The best part was a saving of near 100 dollars. I am extremely pleased.
Thank you,
Gene Guthan
Santee, SC

Parts Used:

Jean from Santee, SC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

tube was rusted out

just removed two screws - took old unit out - put new unit in.

Parts Used:

Barbara from Whitefield, ME
Difficulty Level:
Difficult
Total Repair Time:
Less than 15 mins
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Old burners were worn out and wouldn't light with the ignitor

Removed two screws and replaced burners and placed the unit back into position and the burners worked perfectly. Very easy. I think anyone could do this task.

Parts Used:

Charles from Bangor, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

I wanted to replace my grill/griddle attachment with 2 burners

Ordering was a snap, and I received the part only a couple of days after I ordered it.

This was easier than installing a lightbulb! All I did was take the part out of the packaging and plug the gas burner assembley in, add the cover to the burners and add the iron burners plates on top. The entire thing took less than 5 minutes!!

Parts Used:

karen from Haymarket, AL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

it was painless

just as stated before. Remove old burners from plate and reattach new burners.

Parts Used:

judy from clifton park, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

simple swapping of parts

Undid the bad part and installed the new one

Parts Used:

lenny from east freetown, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Burner wouldn't light.

Took out a couple of screws and put in the new part. PartSelect was fast and efficient. Highly recommended.

Parts Used:

Clark from Tifton, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Burnner rusty and will not start with electric start.

Removed and installed burners in less than 15 min with just a nut driver. Replacing the burn ere did not fix the starting problem, but replacing them did improve the hurried flame.

Parts Used:

Robert from Mary Esther, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

The stove top parts were stained and unsightly. I did not realize but the burners did not light correctly--i just adjusted. I was about to have an appliance person come fix the burners I use most. The burners came with the tray and grates.

I removed the old burner assembly and replaced it with the new one. No tools necessary. The stove looks brand new.

Parts Used:

MODULE

Marilyn from South Freeport, ME
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Needed to convert Jenn-air grill to burner.

This is a Jenn-air burner replacement or converter kit for the grill. It was basically a take out, put in scenario. It was quick and easy.

Parts Used:

MODULE

Caroline from Portland, OR
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

128 of 1633 people found this instruction helpful.

Was this instruction helpful to you?

12 yr old Jenn Air range top was awful

Took out old burner assembly and replaced with new parts. All done by hand and took about 3 min. Perfectly working old range looks new. Wonderful!

Parts Used:

Sara from Charleston, SC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

111 of 2453 people found this instruction helpful.

Was this instruction helpful to you?

Burners would not light - rusted

New front burners fit well, but back ones had just enough variance in tne angle of the gas-supply tube that it would not fit the mounting bracket holding both burners in place. I had to grind a small flange off of the bracket so the gas tube would clear. Once that was done the burners worked well.

Parts Used: