Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Random clicking noise
3 of 4 peoplefound this instruction helpful.
Mark from SAN DIEGO, CA
Very Easy
15 - 30 mins
Nutdriver
The toughest part was pulling the refrigerator from the wall....After removing the back-bottom access panel the compressor is right there with the Start-Dev and Cap..Took a few min to remove and install new parts....Very Simple and works great...no more clicking..
I first removed the icemaker pump and filler tube fron the back of the refrigerator by using an adjustable wrench and pliers. (very simple connection) I went ahead and replaced both items at that time.
Next I opened the bottom freezer and removed the top wire tray and ice container. I removed the bottom nut from the ice maker
... Read more, pulled the electrical plug lose from the freezer connection. I then just lifted the ice maker upward and off the two screws on the side wall and out it came!
I had a little trouble with the filler tube as it came into the freezer. I had to go back and forth to the back of the refrigerator and freezer a couple of times adjusting the tube, so it woiuld clear the inside freezer wall.
This was a very minor problem. I feel like if I had followed the instructions and made sure the tube came through before attaching the icemaker it would have worked like a charm!
What I really liked, was everything was in the box for the job.
Read less
Was this helpful?
Thank you for voting!
Water not draining to pan. It caused an ice build up under the freezer draw
3 of 4 peoplefound this instruction helpful.
Rich from WINSTED, CT
Very Easy
Less than 15 mins
Nutdriver, Pliers, Screw drivers
Remove the grate at the back of the refrigerator. Remove the existing drawn tube. Replace the exiting drain tube with the updated drain tube. Check to see if water was draining properly. Replace the grate. Sit back and have a beer.
Was this helpful?
Thank you for voting!
did not have a ice maker
5 of 10 peoplefound this instruction helpful.
Ralph from Argenta, IL
Really Easy
More than 2 hours
Nutdriver, Pliers, Screw drivers, Wrench set
remove parts that were not need installed water valve , ice maker unit and hooked up water supply tested and it works fine. got the parts really quick Thank You
Was this helpful?
Thank you for voting!
peg that swings the pantry door open and closed was broken off
2 of 2 peoplefound this instruction helpful.
Dalton from BEAUFORT, NC
Really Easy
1- 2 hours
Nutdriver, Screw drivers
watched partsselect video and simply followed the directions
Was this helpful?
Thank you for voting!
Freezer cold ; fridge warm . Freezer not defrosting.
2 of 2 peoplefound this instruction helpful.
Tim from Oxford, MA
Really Easy
1- 2 hours
Screw drivers
Unplugged fridge Pulled light cover off Used screwdrivers to press in on tabs holding control board cover. Unplug wiring harnesses. Snapped board in two. Install in cover Reattach wires Done
Was this helpful?
Thank you for voting!
ICE BUILD UP AT BOTTOM OF FREEZER
3 of 5 peoplefound this instruction helpful.
Gerald from COLORADO SPGS, CO
Really Easy
30 - 60 mins
DEFROSTED REFRIGERATOR COILS, BUT DIDN'T REPLACE THE GROMMET.
Was this helpful?
Thank you for voting!
The old shelf shattered when we tried to clean it
2 of 2 peoplefound this instruction helpful.
Michael from COAL VALLEY, IL
Easy
30 - 60 mins
Just slipped it in. I think it's a very poor design.
Was this helpful?
Thank you for voting!
Freezer not defrosting and making fridge run warm.
2 of 2 peoplefound this instruction helpful.
Brent from PRESCOTT, AZ
Really Easy
30 - 60 mins
Nutdriver
Super simple following the instruction video you posted. Thanks!
Was this helpful?
Thank you for voting!
Vertical mullion rail broken
2 of 2 peoplefound this instruction helpful.
David from Massena, NY
Very Easy
Less than 15 mins
Nutdriver, Screw drivers
backout one screw, push mullion up and free from upper and lower slotted tabs, disconnect one electrical connector. Reverse the steps to reinstall. Literally took 2 minutes.
Killed the power to the fridge. Then, used a small, thin screwdriver to depress the clip on the bottom of the switch and wriggled the old switch out. The two wires easily came off the contacts with pliers. Connected the wires to the new switch and snapped it into the hole--clip facing down and contacts facing up. Turned the power back
... Read more on and checked the switch. Worked perfectly! Easy job.
Read less
Was this helpful?
Thank you for voting!
The vertical mullion rail went bad
2 of 2 peoplefound this instruction helpful.
Ed from OCEAN CITY, NJ
Very Easy
Less than 15 mins
Nutdriver
I left this broken rail hang off my refrigerator for almost a year I finally decided to investigate the possibility of ordering the part on line. I found the part on line in minutes and when I received the part it literally took me 3 minutes to install.
My Orders
