Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Broke the Rocker Switch in Fridge side
4 of 6 peoplefound this instruction helpful.
Sung-Su from BISMARCK, ND
Very Easy
Less than 15 mins
Popped out with butter knife and unplugged 3 prong connector and reversed with anew switch.
But, unfortunately it got broken again exactly same way as before. So, I ordered same switch again for 2nd time.
Maytag should recall that Rocker Switch and build with better materials.
Was this helpful?
Thank you for voting!
Center Crisper Rail Broke Off At One End--Drawers Would Not Slide And Hang Right.
4 of 6 peoplefound this instruction helpful.
DANA from ASHTABULA, OH
Really Easy
Less than 15 mins
Very easily removed top shel glass above crisper--removed old rail by lifting up--and place new one in slots provided---simple!! Part was delivered in less than 3 days-------very fast and cheap !!!
Was this helpful?
Thank you for voting!
One of the plastic fasteners had broken so the entire part needed replacing.
3 of 3 peoplefound this instruction helpful.
lane from EVERETT, WA
Very Easy
Less than 15 mins
Socket set
Turned off power, Removed screw, disconnected wire harness and removed old rail from door, Connected new wire harness and attached new rail to door, replaced screw. Restored power. Done.
Was this helpful?
Thank you for voting!
Freezer freezing up. Frost everywhere.
3 of 3 peoplefound this instruction helpful.
Daniel from LAKE CITY, FL
Very Easy
Less than 15 mins
Old gasket pulled of easily with no tools. New gasket was placed on floor and heated with blow dryer to straighten. Then installed new gasket by pressing in with my hands. Noticed that the old gasket was hard and not flexible. All was great. Fit perfectly. No frost after a week. Happy.
Was this helpful?
Thank you for voting!
Broken center crisper rail
3 of 3 peoplefound this instruction helpful.
Allan from Tucson, AZ
Very Easy
Less than 15 mins
Total time 10 minutes. 9 minutes to clear out the food and 1 minute to install the part. Installation was self evident and could have been done blindfolded. Part just snapped in.
Was this helpful?
Thank you for voting!
Door Gasket had a tear in it.
3 of 3 peoplefound this instruction helpful.
Ida Mae from MEDLEY, FL
Very Easy
15 - 30 mins
Screw drivers
To repair the problem,I ordered a new gasket. Once I received the gasket, I laid it flat on the floors and hot the blow dryer and blow out the creases in the gasket. I then took off the door by removing the four screws from the door and rest the door on the table. I then removed the old gasket and replaced it with the new one. It took a
... Read morebout 15 minutes. My frig. Stop freezing up.
Read less
Was this helpful?
Thank you for voting!
Refrigerator freezer stopped cooling
3 of 3 peoplefound this instruction helpful.
Robert from COALINGA, CA
Really Easy
15 - 30 mins
Nutdriver
Prior to ordering I removed freezer panel and checked for ice build up and fan functionality. Then removed rear panel cleaned lint from everything pulled front panel vacuumed out the condenser. Plugged back in and all seems to work with the exception of compressor. I have a little experience so googled in model number and your site popped
... Read more up. I looked up part and the site gave me a percentage loved that. I ordered wish I would have rushed shipping as took about 10 days. Installed in less than 30 minutes and all runs great ??
Switched the drain out using the video tutorial Fixed the problem Have had no more drain issues
Was this helpful?
Thank you for voting!
Broken clips on old part
3 of 3 peoplefound this instruction helpful.
Rose from OCOEE, FL
Really Easy
Less than 15 mins
Snapped in new part
Was this helpful?
Thank you for voting!
Right door seal was torn at top of door
3 of 3 peoplefound this instruction helpful.
Richard from MIDDLETOWN, MD
Really Easy
Less than 15 mins
I followed the remove and replace instructions in the Part Sect video when I ordered the seal. Pulled out the old seal by hand and installed the new seal. No tools needed, very easy. Took 10 minutes at most.
Was this helpful?
Thank you for voting!
Center Crisper rail
3 of 4 peoplefound this instruction helpful.
Richard from PASADENA, CA
Really Easy
Less than 15 mins
Take everything off the top self, lift the self install the new part ,put self back in place and then install the drawers again. Took minutes.
Was this helpful?
Thank you for voting!
I purchased a display model that was missing a part.
3 of 4 peoplefound this instruction helpful.
Monte from Longview, WA
Really Easy
Less than 15 mins
Snapped on the new toe grille.
Was this helpful?
Thank you for voting!
broke my original Kickplate Grille
3 of 4 peoplefound this instruction helpful.
Daniel from GEORGETOWN, TX
Really Easy
Less than 15 mins
knelt down, positioned replacement kickplate; popped into place, stood up!
took longer to open the box and peel bubble wrap off item than to replace it!
Was this helpful?
Thank you for voting!
I had a loose fitting old condensor fan blade on my new motor.
3 of 4 peoplefound this instruction helpful.
Roger from SMITHFIELD, RI
Very Easy
Less than 15 mins
Nutdriver
I made a temporary repair by drilling the old blade plastic hub and put a small screw in it to hold it on to the shaft until the new blade arrived. The new blade came in within the two days I needed before Thanksgiving. I removed the old and pushed on the new. There were 8 screws on the back guard and two to hold the motor on. It was a
... Read moresnap. Thank you PartSelect.com The wife is very, very happy now, we had 51 coming over for Thanksgiving. :)
My Orders
