AEE953 Speed Queen Dryer - Instructions

Installed the new part. Worked great!

I unscrewed the door catch and pried out with some resistance the strike part. Screwed in the catch and pushed in the strike. Closed door. Voila!! Back in business with assurance.

I began by removing the two screws at the lower part of the front panel. After removing the panel I was able to access and remove the broken switch which was located on the front panel. I popped out the old switch and replaced it with the new one, reattached the wires and put the front panel on and the jod was done.

Unplug dryer. Remove lower panel.Remove dryer lent duct. Remove Thermostat fm fan housing. Remove Fan.Remove Fan housing. Remove Motor assy by sliding out, wires lay toward front, allowing room to replace idler pulley and spring. Use lock ring pliers to remove pulley from shaft. Grease pulley/shaft w/high temp grease [I used ultra-hi temp ceramic brake grease-can get in small packets at auto stores].Noise/slippage has all but stopped. Lesson: replace rear rollers and front felt/glides. Belt looseness also caused by worn rear rollers [smaller overall diameter from age]-even though they spin freely

Unplugged dryer removed the front, removed & marked the wires. Removed the drum & drive belt. Removed the snap ring on front of roller with a pgtai awl.Removed the wheel & worn washers, removed the nut on the back of the roller shaft. reppaced it all in reversed proceedure. Other than a few little scrapes on the knuckles it was Quite easy.

I tested all the thermostats and fuses and the heating element with a VOM. I found that the thermal fuse was bad and replaced that and it heats fine. The hard part was reaching everything from the front of the dryer. Poor design for access. Also replaced the door switch while I had it apart.

The repair went very well. The parts were a perfect fit and arrived earlier than expected.It took a little longer than it should have to do the repair because of my recent surgery I had my 11 year old grandson operating the nut driver taking the dryer apart install the parts then reassemble under my watch full eye. You could say it went so easy a fifth grader could do it.

Disconnect power. First, remove the lower front panel, then the upper front panel (disconnect door switch wiring). Remove two screws holding the top panel to the left and right side panels. Remove wiring connections to light and humidity sensor. Remove four screws to front drum support assembly, lift up to disengage tangs, and remove assembly. Reach in and find the idler assembly for the drum drive belt, and unwrap the belt to loosen it, also removing the belt from the motor pulley.. Slide the drum out the front of the dryer along with the drive belt. Remove the snap ring (using snap ring pliers) and washer holding the idler pulley on to the idler assembly. Remove the idler pulley. Polish the shaft with fine steel wool to get rid of dirt. Clean thoroughly, leaving no steel wool residue. Install replacement pulley, washer, and snap ring. Reinstall drum, taking care to feed belt back into place as the drum is reinstalled. Reach in and wrap the belt around the motor pulley and the idler pulley. Reinstall the front drum support by lifting the drum slightly to allow the support to engage with the drum, and then drop it down to re-engage the tabs into the left and right side panels while reseating it into the blower intake. Install the four screws to hold it in place, and reinstall the wiring for the light and the humidity sensor. Attach the top panel to the left and right side panels with one screw for each side. Reinstall the upper front panel, including reattaching the wiring to the door switch, with two screws. Finally, reinstall the lower front panel. Reconnect to the power source, and you should be good to go.

disassembled the entire dryer drum and front bulkhead plate. Installed belt and replaced drum on rollers and positioned idler pulley .Video was very helpful in positioning drum and belt onto idler pulley. More trouble with the existing dryer vent replacement after repairs were complete

Went to YouTube and put in good.. did not fix the problem with the dryer but it has a new belt on it now!

Removed lower front panel.

Removed door assembly* making note of the wire positions on the door switch
* When removing the door assembly DO NOT LET IT DROP DOWN! Doing so will destroy the door switch. Swing the door assembly upward from the bottom toward you as high as it will go then pull it free.

Removed the drum and belt assembly.

Removed the idler pulley and idler pully spring.

Vacuumed up the interior dryer floor and blew out the motor w/ comp air. Also cleaned the ribbed motor pulley with a nylon brush and brake cleaner sprayed on a shop towel.

Removed the drum tires and cleaned their shafts and internal bearing sleeves with brake cleaner sprayed on a shop towel.

Reinstalled the drum tires after lubricating their shafts with a very light coat of general purpose grease.

Replaced the idler pulley and idler pulley spring after cleaning and lubing shaft and pulley bearing as done on the drum tires.

Reinstalled the drum with the new belt (ribbed side down) roughly in place.

Reinstalled the front door assembly after reconnecting it's wiring making sure to insert it's top locking tabs with the bottom of the door held up high then swung down into place

Tensioned the belt by positioning the flat side of the belt that comes down the right side of the drum over the idler pulley flat side down and then the ribbed side of the belt over the motor shaft. You will have to move the idler pulley arm to apply full tension against the spring in order to have the slack to get it around the motor shaft.

Reinstalled the lower front panel.

Checked dryer operation OK.

This repair was rated a bit difficult because I didn't know the trick for removing/installing the door assembly and destroyed the switch. Furthermore, putting the belt back on is a somewhat difficult challenge because you have to do it mostly by feel

Disconnected dryer from vent and power receptacle, placed dryer on its back and remove the front panel by removing screws along the bottom of the panel and pulling down on the panel. Below the drum the element mounting plate was visible so I removed the sensor and element wires, removed the element mounting screws and pulled the element down and out of its "duct". I installed the new element and replaced the wires and front panel. That's all folks!

The front of the dryer needed to be taken off, the drum needed to be taken out and the belt installed on the wheel structure.
I was very pleased at how fast I received the part after ordering it! I will definitely use this site again when ordering replacement parts!

I followed the online video on PartSelect website. No other instruction necessary.

My husband pulled drum out of dryer and replaced the idler pulley wheel and decided to replace the belt while he was in there. It's good to have a snap ring tool as it's a pain to replace the snap ring without this tool. Goes alot quicker!