ADE7005AKW Admiral Dryer - Instructions

No problem

Ordered the part, you made it so easy. Received it in two days, very fast, by regular mail. Perfect fit. Pulled out the old broken one and put in the new one!

After watching the great install video, I followed his lead and within 20 min had my dryer door fixed. This dryer was bought in 1986 and I really thought I was looking at buying a new dryer. How wonderful that I could fix it for less than $11. Easy to find web site, easy to find part, great instructions and fast delivery!

Very simple repair. Remove front panel, door, drum etc. Try to keep everything seperated, screws etc. I put lockjaws on the back to get the nut off the front. Make sure to check the housing for "melted on" blower wheel residue. Easy enough to remove. I checked with my local parts dealer he wanted twice the price and needed to order it (at least a days wait). PartSelect sent the exact same part in a day and a half. Put everything back the same way I removed. Hardest part is the drum and belt. While you have everything apart don't forget to clean the thermastats etc. PartsSelect was quicker and cheaper.

Opened top cover at corners to access screws on each side of front. After removing screws from inside of front door, lift the door and panel off of retainer clipson the bottom front corners. Thermal fuse is located at the back left side mounted on the heating element cover. Can be checked for contunity if open. Next to it is the thermaostat limit control. Both should be replaced, even if just the fuse is open. Why? The dryer took long to dry since it was new. This not only corrected the starting problem, but it now dryes faster. Apparently a defective thermostat limit when it was new.

Idler was the noise source. Drum support rollers were failing also. I almost spent $500.00 on a new dryer, glad I replaced the parts instead. Sounds and works like new. Watch the video,its very helpful. Thanks Parts Select. You should advertise your services on TV or radio. I am glad I found you.

Make sure to unplug the power cord.Pry the front,top of the dryer up with a screw driver. Carefully disconnect 3 wires and remember where they go, top right. Remove 1 top bolt on each side of the front cover, inside.Pull up slightly and towards towards you to remove the front cover. Disconnect the light wires if applicable and remember where they go from the front drum support. Remove 4 bolts on the front drum mount cover; the lint catcher will come off with it. If needed, pull up and towards you on the drum to lower the it off of the guide rollers to allow slack in the belt. Reach under the drum, raise the idler lever, slide belt from under the idler lever pulley, remove the belt from the the motor shaft. Carefully remove the drum. A 7/16 wrench and ratchet can be used to remove the idler lever from the mount. Remove idler lever from the spring. Reverse these steps for installation of the new idler lever. For installing the belt, actually fold the belt and put it under the idler pulley and back onto the motor shaft. The idler lever should sit on top of the belt when on properly. Make sure the belt is lined with the wear area of the dryer drum. Roll the drum manually, counter clockwise several times to help insure belt alignment before reconnecting the wires and re-installing the front cover and top. A belt replacement will not require removal of the drum.

I pretty much followed a lot of the earlier postings on partselect.com that provided encouragement to pursue replacing this part on my 17 year old dryer (sorry, money is tight these days and I prefer repair to $800 replacement).

I'd like to add that I borrowed a pair of snap-ring pliers from work which made removal and later securing of roller onto shaft much easier and probably avoided a lot of knuckle bruising and cursing.

I erred though in a couple of places during the replacement. Disassembly took about 20 minutes. However, when I re-assembled I had mistakenly already put the roller onto the shaft before trying to put the drum back in. That isn't possible so I had to remove (an initial groan but only a few extra minutes in the end) the roller from the shaft, then reposition the drum and then the roller back on the shaft.

I also decided to replace the belt while I was in there and I should have taken a picture or made a drawing of the belt route before I took it off since I was later left pondering how the heck to snake the belt onto the shaft and also the tensioner. A quick trip to the internet though showed me a similar route and reminded me how to route it.

I'd also like to add to be cognizant of the wires on the door and front panel when disassembling.

Anyone with any sense of mechanical ability and a little common sense ought to be able to do this repiar.

Thanks Part Select!

Used spackle knife to pop clips on top of dryer. Raised lid of dryer to expose belt. Next used nut driver to disassembly screws from front door and then base ( bag them. Labeled bag and marked inside of dryer with corresponding number to match hardware) disassembled dryer door latch switch and marked red + and white no marking. ( Middle connection not used) removed dryer clean out screen and then removed dryer face next removed dryer blower cover no hardware ( just lift upwards see side clips) opened up side of dryer to gain more access (spread apart manually) removed belt and marked where belt was on tumbler postion with permanent marker used 2 car hold down cords to hold drum in place with back of dryer next removed belt from idler (note to make a drawing so that you know how to wrap this around the idler otherwise the belt will appear to be too large. Remember to reconnect spring. Next step was to removed drum rollers. . . This required a retaining ring pliers cost about $15. I replaced the snap retaining rings. This was easy but requires that you pull the drum forward about 4 inches to position. Next replaced belt and reassembled. Project was a success and runs like new. . . . Saved me $129 service call plus $65 parts without maytag mark-up plus additional labor for the job $130. My cost $65 + $15 tool (retaining ring pliers) $80 versus $259 + ( $65 *50%)ark up on parts) $80 versus $356 -- thanks parts select for saving me $276 during the christmas holiday.

How to take apart a dryer:
The first way:
1) Remove front lower panel (2 screws on bottom).
2) Remove the front black plastic air duct.
3) If you have long arms, or an extention socket wrench, you might be able to reach the heating unit, otherwise use the Second way:

The second way:
1) Remove front lower panel, as this will expose the screws to the dry door unit.
2) Remove dryer door unit (2 screws on bottom, 2 spring clips on top), and disconnect assoc wires.
3) Remove dryer lid:
3.1) Remove 2 screws on front (previously hidden by door unit
3.2) Remove 2 clip hooks on back of dryer
3.3) Lift lid rear above center guides, and wiggle away from front spring clips
4) Lay dryer on back, as this will allow easier removal of the drum
5) Remove screws securing the heater control unit.

Attempt 1: Disconnected heating element and saw that the heating coils were broken. Ordered new heating coil and new belt.
Attempt 2: 3 weeks after installing new heating element, my wife informed me that the unit was no longer putting out heat!!! So, I ordered the Thermostat and Thermal Fuse. Put dryer back together.
Attempt 3: Turned it on - absolutely nothing - dead, dead, dead. Discussed purchasing new $600+ dryer. Started taking it apart again, and discovered that door wire was never reattached. Meaning the dryer thought the door was wide open.
Attempt 4: Now the dryer squeaks. Took dryer partially apart and added white grease to wheels that support the drum. Currently, all is well with the world.

Moral of the story: Replace the entire heating unit, check belt for cracks and grease the wheels if you get a chance.

The repair looked simple enough until it came time to take the out wheel off. Because you can not hold the motor shaft(and the wheel screws on) it was necessary to remove the whole motor assembly and then grind the out shaft down, then use a small screwdriver to take the remaining shaft off.
I must say it was nice to recieve the part in as fast as I did we live in a very rural area and things like that are very hard to find

Being my lousy Maytag washer died THE PREVIOUS DAY, spewing water, etc. and I had rushed out and bought a new washer, I was determined not to replace the dryer (though I now am a serious NON_FAN of Maytag).

I disassembled the whole dryer and finally got to the blower wheel which was broken lose from the molded nut. I supposed something like a dime or penny got in there to shred it.

PartSelect's website allowed me to find the part in 5 minutes. It was on my doorstep the next afternoon.

Installation was straightforward BECAUSE I stacked all the screws and and labeled them appropriately. It took about 30 minutes to reassemble and the toughest bit was getting the drum in with the belt positioned properly.

Removed front panels and swiveled lid upwards. Loosened tensioner, removing belt and then carefully extracting the drum. Replaced 2 drum glides on underside of front panel. Next 2 rollers, which appear to unscrew, but do not do so. You must remove the retaining ring (surprise! ...and 2 screw drivers later). This was the longest and most frustrating part of the whole ordeal. Then just reverse the process for reassembly. This was my first electric dryer repair and it really wasn't too bad. Online docs I found were somewhat helpful, but really luck and perseverance. I did save probably $300 in replacement costs, which is quite satisfying. .

I first removed the front panel and door on the dryer using a 5/16th nut driver. I needed to disconnect the light and switch to remove the door. I raised the top lid of the dryer to expose the drum. I rmover the fan schroud and lint filter by removing 4 5/16 screws with the nut driver. I disconnected the belt from the idle tension pully and removed the drum. The drum support rollers were visible on the back frame of the dryer. I removed the bad roller using snap ring pliers. After cleaning the roller support shaft and lubricating the shaft with grease I replaced the drum support roller and secured it with the snap ring. I also replaced the dryer belt although it was still workiing. I reasembled the dryer after giving the inside a cleaning with the shop vac. The hardest part was getting the belt secured with the tension idle pulley. When assemblying the fan schroud make sure it is snug against the fan so it doesn't leak. Replace the top and front door and cover connecting the switch and light. If you get the switch wires correct the dryer will run with the door shut otherwise reverse the wires.

Had to lay dryer on back. Cause it didn't have a back cover had to take the front door off and go in thru the front. Had to take the vent off. Had to use scotch tape to hold the belt in place while I got it on. It would have been a lot easier if they had a back cover. I only hope I don't have to do it again as it squells a bit on start up. Bill