ADB1500AWS2 Amana Dishwasher - Instructions

I would not have figured it out had I not viewed the video on installing the latch assembly. The latch must be in the LOCK POSITION before installing. It would help if the latch was in the LOCKED position before shipment.

remove 11 screws, remove old latch after disconnecting electrical wires, connect wires to new latch assembly, and replace 11 door screws. Easy breezy.

Remove all interior door panel screws with a torx head screwdriver (drill). Pull the interior panel up from the door far enough to access the switch assembly. Pull it out and remove the 2 electrical connectors from the old switch (using a small screw driver as a pry bar if needed). Remove the old switch and handle (that may be broken off and still in the door). Push the electrical connectors onto the new switch assembly, making sure the handle is down toward the opening and the connectors are on the same side as they came off of the old switch. Align the mounting screw holes of the switch with the threaded holes on either side of the switch. Push the interior panel back together and align the two holes with the switch holes (those 2 screws go through the door panel and the switch assembly). Replace the remaining interior panel screws. Done!

Unscrewed dishwasher from counter and pulled it out from under the counter a few inches. Looked at the side of the dishwasher with the remaining good spring and saw how it was attached: One end was hooked to a little tether strung around a pulley, the other to one of a few steel slots. Copied that side for the new spring and works fine now.

The original piece is 100% plastic (with metal shields only to prevent burning). The bushing of the arm was badly worn out in one side. The arm was no turning properly or at the end no turning at all. I decide to drill the new part in order to fit a brass bushing inside (1/4" ID, 5/16" OD, about 2" long). I expect it will last considerable longer. I would say this is a typical "defective by design" problem.

from inside the door remove torx screws down each side and top , pull panel back , removed 6 screws from back of dispenser ,unplug 1 wire connection ,reverse procedure , real easy repair.

I remove the inner door panel, disconnected two quick release connectors, unscrewed the old part from the inner panel and installed the new one.

The new part arrived quickly and was the perfect match.

The repair was much simpler than I had anticipated. I just started removing screws, remembering what screws went where, and carefully removed the parts I needed to until I could get to and remove the filter unit. Installing the new unit was a snap, then it was just a matter of putting everything back together.

Wanted to change our dishwasher to a stainless steel appearance. When the panel was delivered in 1 day I might add it was flawless. I removed the old panel and the new panel attached to the dishwasher perfectly with the screw holes exactly lining up. The most inexpensive way to turn a kitchen into a stainless steel appliance look.

1.Disconnected the electricty 2. pulled the dishwasher from under the cabinet 3. tilted the washer on it's face (water supply was long enough and did not need to disconnected.)4. unscrerwed the 2 plastic nuts that hold the heating eliment in place. 5. tilted the dishwasher back upright and removed the old heating element. 6.put the new part in place had a helper tilt the washer forward while i tightened up the two plastic nuts to hold the part in place.7 reattached the elecrtic conectors to the heating element. 8. pushed the dishwasher back in place. 9 hook the electricity back up. During step 4 i had to remove the electric connectors from the old heating element.

By reading online about some similar problems, I discovered that the accumulator did, in fact, have some holes worn through the screen and was leaking sediment back into the rinse water. After waiting for 2-3 months because the apart was on back-order at the factory, it took me less that 1 hour to remember how the unit went together (reviewed the parts diagram online) and connect everything up. On the first rinse, the dishes were really clean - well worth the wait. Doing dished by hand reminded me of the old days....

Snapped the old part out and snapped the new part in.
It was a piece of cake.

Repair was fairly easy. There are 11 screws You have to remove then simply unplug the electrical connection from the door latch/switch and plug in the new one line up the screw holes tighten them down and your in business.

Turn off the DW power (pull the fuse or turn off the circuit breaker) Open the dishwasher door. Remove the torx screws around the periphery of the door inner panel. Lift up the inner panel far enough to get at the door latch. Lift out the entire door latch assembly. There are two wiring connectors attached to microswitches on the latch assemby. Remove the connectors. The connectors were pretty tight, so I needed pliers to pull the connectors off the switches. Discard the old latch. Get the new latch, and plug in the connectors (keep track of which wires go on which side). Lay the latch down in the door so it lines up with the mounting holes. Lay the cover back down, start each of the torx screws into their threaded holes, then tighten them all. Don't over tighten. Turn power back on. Job done. It almost takes as long to type it up as it does to make the repair.

First I removed the torx screws halding the inner door panel on. I then seperated the door panel from the door and removed the latch assembly and disconnected the switches from the latch. After installing the switches on the new latch I replaced it between door and inner panel. Finally I replaced the torx screws and was finished.