9875XYB Magic Chef Wall Oven - Instructions

Screwed in light bulb and glass protector

Removed two screws, unplugged the old unit, plugged in the new, screwed the new in. Job done. Would have been less than five minutes if I hadn't kept dropping the screws.

Removed frame to cabinet lag screws
Slid oven out of cabinet (required because wire harness could not be pulled through inside of oven)
Removed two screws holding attaching sensor inside oven
Uncoupled wire harness
Installed new sensor in reverse order

Unfortunately, neither the new bake element or sensor fi ... Read more xed the problem, so I just ordered the more expensive control board -- hope that does it.

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

This was a very easy repair and the website helped greatly. my husband simply pulled old element out and pluged the new one in. Excellent website, saved us a lot of money.

Turned off power at breaker box. Removed two screws from the old bake element on rear of oven wall. Pulled out bake element from back of oven so wires were exposed (about 3-4 inches). By hand, removed the wire connector from each side of the element (wiggle it loose).

The part I purchased was exactly as described on the PartS ... Read more elect website (i.e., it had the correct connections - female - on the bake element). The part arrived in 2 days in perfect condition. I definitely will use PartSelect again.

Installed new thermostat. Went well. Now the oven comes on and it takes 2.5 hours to come up to 250 degrees. Help!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. That is when I notice that the new element had a female connector and so did my wires comeing out of the stove. I took the old elements male end off (with a grinder). The mail end was long enough to u ... Read more se it connect both female end.

We took the back off the stove and unscrewed the two screws from the inside holding the sensor on and pulled it through and plugged it in and then replaced the screws. Very easy. We are still having trouble as the display does not read the same as the tempature is in the oven.

Followed video

The hardest part was deciding if this part would fix the problem. The upper oven became unusable. Both elements worked fine until reaching temperature. The oven would not come back on after that. I took two screws out. Then I pulled the wires out and unsnapped the coupling. The install was reverse. I just snapped the coupling in pla ... Read more ce and replaced the two screws. All works fine now. Saved a couple thousand as wife was prepared to buy a new one.

Replace the oven sensor per the excelent easy video you provided

removed 2 screws in probe and pulled it out.had to take back off as wire was tangled from factory and couldn't do quick repair

There are five Phillips head screws to remove from the door (2 top, 3 bottom); the only touch part is that there are no screws on the sides, but instead plastic tabs on each side that "latch" inside the door frame; you have to use a flat blade screwdriver to work each tab and press on the door frame to unlatch each tab (yup I broke one, n ... Read more ot knowing the setup the first time, but it went back together OK anyway). Once the tabs are unlatched from the frame, the entire front or the door will come off (be ready for this); then, just a few screws to take off the 2nd inner door glass frame (remove second glass carefully), and your to the inner glass, which just fits within the frame. Then, carefully backwards and the door is together again (once again, provide support as you take the last tab/screw off the outside of the front door, or you'll have more broken parts).

I watched the video, which was very helpful...the temperature sensor was hard to pull through the small opening in the upper back left oven corner. On the back wall of the oven was a large removable circle, so I unscrewed that piece and was able to gain access to the wires attached to the temperature sensor and push it through the small ... Read more opening. I used one of the new connectors, pushed it back through the small opening, screwed it back onto the oven wall, replaced the circle opening and tried the oven again...unfortunately, there was no improvement in oven temperature! My JennAir wall oven is about 17 years old, and I thought I would try this $30 repair prior to purchasing a new wall oven, but it looks like I will have to do some overtime and buy a new oven. Any other suggestions would be welcome.