9875XYB Magic Chef Wall Oven - Instructions

After removing two screws, I pulled the bake element free from the oven's female electrical connections---only to find the new element had female connectors, too. Nevertheless, I cut the male connectors off the old bake element and used them as a splice (of sorts). Then installing the new bake element was a piece of cake, which I can make now thanks to PartSelect.com.

A web search led me to Parts Select. Two days later my bake element was installed and my oven was again in bake mode.I'm a 75 yr. old grandmother and installed it myself so that should tell one how easy it is.

the heating element burnt out the Monday of Thanksgiving week. I received the part on Tues and we repaired the stove on Wednesday. Since this was the second time we had to replace the heating element, it was much easier the second time around. We removed the old element and installed the new one in less than 30 minutes. It was an easy fix. The new element evenly bakes the food now.

Removed the oven from the wall. Removed back cover and unplugged sensor from the harness. Remove and replace sensor from inside the oven. Reconnect harness and reinstall back cover. Secure oven back into the wall.

Replaced the long Oven Sensor but have not resolved the root problem. Oven still will not reach required temperature. Bottom element becomes red hot, but turns off and will not start again.

Had to remove oven from mounting cabinet to get to the back since the wire lenght to the conector was to short to come through the mounting hole.
Other than that the repair was straight forward. 4 screws to dismount the Oven from cabinet, 2 screws to remove Sensor and 3 srews to open the back of the oven once out in the open. New cable adapter that came with the new sensor was needed in my case.

Flipped off breaker and removed oven door and pulled built in stove out so the back panel could be removed. Unplugged the sensor then removed the two screws securing the old sensor inside the oven and installed new sensor. Put stove back together and installed back into counter top, re-installed oven door, flipped on the breaker and oven works like new.

After trying to set the bake temp after the self cleaning, it would not heat up. I Googled the model number,selected your link because it mentioned my symptom,and said usually it is the temp sensor in the oven that gets damaged by the high self cleaning heat. Your site had a place to enter my model number. You provided a great exploded view of the parts, showing me my sensor,then you provided the part number of the kit i needed,and filled out the order form with payment method. Less than a week later I got my part with instructions. Your video showed me the two screws I remove from the front ,and I pulled the old part out and uplugged it's connector. Replacement was easy, and oven was fixed! Thank you for a great site! You held my hand through it all!

Easy in and out, just two screws and two wires. Only additional work was that my oven had female spades on the wires and so did the new element. Took a couple of extra minutes to change out the spades on the oven connections. Then it was slide the connectors together, re-attach the two holding screws and the oven was fully functional.

First replacement element came in bent, Parts Select shipped and replaced it immediately!

Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All checked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.

easily pulled old seal out and push new seal in place simple and quick.

Once I saw the spring clips on the new door seal, it was easy to understadn how to remove the old seal and install the new one. Looks nice !

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

Removed screws on each end of element, pulled off spade connectors, did everything in reverse for new element.

The only notable fact was that the old element was hot, as in carrying AC current, despite the stove being off and it being broken, and I found out the usual way.

Control panel was responsive however oven would not heat up. I Replaced sensor with one of the adapters and oven is now working again.