8361RV Magic Chef Cooktop - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broke the insulator on the ignitor while cleaning the cooktop.
Unscrew the bottom cover, remove the old ignitor. Reverse the process to install. Hardest part was getting the bottom cover screws out because of rust. Otherwise, very simple.
Parts Used:
-
David from Shelley, ID
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Missing regulator when floor model gas cooktop was purchased
1. Apply gas pipe joint sealer to treaded nipple on bottom of cooktop; 2. Install regulator on nipple with regulator direction arrow pointing to top of cooktop; 3. Tighten but do not overtighten as it may crack the aluminum body regulator; 4. Make sure the face of the regulator with the green painted surface faces the outside of the cabinet; 5. Get a new gas flex hose to connect to gas pipe (got mine at Lowe's - 2 feet long with all the right fittings for about $15). 6. Follow instructions on gas flex hose - make sure you use gas pipe joint sealer only where indicated; 7. Turn gas shutoff valve back on and test for leaks using soapy water; 8. Turn on each cooktop burner to bleed out air.
Parts Used:
-
Jerald from Loveland, OH
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Wrench (Adjustable), Wrench set
Was this instruction helpful to you?
Thank you for voting!
The igniter on my stove wouldn't ignite.
Watched a video on replacing igniter. Removed old igniter and replaced it with new igniter.
Parts Used:
-
keith from massillon, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Burner flame was poor and yellow flames left sute marks on pots and pans
twist old burner and lift out disconnect two wires throw away gasket (if there is one left) connect two wires to new burner set in and twist till tight total time 45 seconds
Parts Used:
-
Jeff from Oconto Falls, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
burner very hard to get out
Used strap wrench to turn out. Rust build up under the burner. Used flat screwdriver to loosen under burner and strap wrench to turn out. Then replaceing the igniter was very easy.
Parts Used:
-
kenneth from brooklyn, NY
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
the top broke away it was corroded
use the pliers. to get. the remaining half off and the screwdriver to cleen the rest of the rust off
Parts Used:
-
Thomas from Floral park, NY
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Gas blowing out from under burners
As the video said, twist burner to the counterclockwise 1/8 turn. Lift the burner straight up. Disconnect the two wires. Remove the burner and reconnect the wires ( they only go one way so they cannot be connected backwards.) Place the burner over the gas fitting and turn the burner clockwise until snug. I turned the power off at the circuit breaker box. The video was extremely helpful.
Parts Used:
-
Dean from Mobile, AL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
Was this instruction helpful to you?
Thank you for voting!
Old burner rusted, flame bypassing
Simply twisted to remove from range top, slipped off igniter wires, attached to new burner, and twisted back into place on range top. Works great,
Parts Used:
-
Pete di from San Diego, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!