79071363708 Kenmore Range - Instructions

Oven ignitor is on the bottom gas unit. Ignitor is in oven and plug is in warmer oven on left wall at very back of warmer oven. It has duel function to light both upper and lower gas burners (in oven). Wires of new plug that I received were shorter than existing wires and would not reach the plug from ignitors center mount location to plug at far back of warming unit on left wall. Even if the wires would have been long enough, I couldn't figure out how to "release" the existing plug. Easy solution: Cut old wires at junction of old ignitor (leaving wires as long as possible). Cut new wired as close to new male plug as possible (leaving wires as long as possible on new ignitor). Strip ends of old and new wires and wire nut with porcelin wire nuts (hardest part of job was locating porcelin wire nuts)! After placing wires out of the way of burner and ignitor, reassemble stove parts. AVOID touching new element as oil from hands will decrease the life of the element. Good Luck..

I "You Tubed" disassembly and commenced by disconnecting electric power. Removed door via You Tube instruction, removed back panels of unit, and replaced the oven temp probe. Easy Peasy. Then removed bottom of oven, next level above the burner and started to remove the igniter. One nut refused to be removed so I removed the burner and cut the nut and drilled it out. I reinstalled the new igniter with a metal screw from the rear panel and reinstalled the burner. Through the tiny hatchway I reconnected the new igniter and reassembled the oven to test. Just fine heated to 350 in 7 minutes. Awesome. Then, I called my brother, Pat, to give his imprimatur to the hillbilly nut switch. He said ok, I am done.

To any reading this, I would order the igniter and the burner at the same time. That tough nut cost my one extra hour.

Removed grates and range cover, unscrewed all sheet metal screws and removed cover plate. Disconnect electrical connector and then removed old ignitor/orifice ass and replaced it with the new one. Replaced all screws in cover plate and then reattached range cover and grates. Turned on the gas and it lit after a few sparks took place.

Tore the oven apart and replaced the igniter, then put the oven back together. Perhaps if Frigidaire manufactured an appliance that lasted longer than three years this wouldn't have been necessary. This is the second Frigidaire range that only lasted three years. Believe, the next stove we buy will definitely not be a Fridgidaire!

Simple: remove the element by hand and replace new one.

I can't believe how quickly I received my new part -literally next day.

Twisted replacement bulb into place easily. Let there be light!

Wife was cooking our thanks giving turkey, when an oder of burning was noticed. I walked over to the oven and smelled the area of oven light, it was bad. I turned off and unpluged oven. Got a screw driver, unscrewed 4 screws then noticed the burned switch from under the oven top. removed 3 wires, covered w/ elec. tape, and pulled oven light switch out front. looked at part number and ordered online. We were able to cook our turkey and enjoyed our meal.

Unplug oven to prevent shore. Make sure to purchase ceramic wire nuts to complete repair. No access to able to plug in the plug. Need to unscrew the plates in the bottom of the oven to get to the igniter. Cut the plugs off and use the ceramic wire nuts to connect the wires. Put make together. It took a Month for the part to arrive.

Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

The range top had to be taken off along with the front panel to get access to the place the burner pipe connects. It took more time to unassemble and assemble the range than repacing the burner. The only issue was that the burner was sent without the bolts that will hold it in place so I had to go to local hardware store to get appropriate bolts.

I couldn't unscrew the leveling foot because it was rusted and corroded. The bracket holding it was easy to remove so I took the bracket with the corroded foot off and replaced it with the new foot and bracket. Very simple. I made sure I oiled it so it wouldn't rust again.

took the two screws out by hand, slipped out the ruined panel, slid the new one in place, replaced the two screws...simple as that

When the part arrived, I open the box. Cut off my breaker to the range. Pulled back the stove and unscrewed the back. Located the probe, unscrewed the one screw that held it in. I then unclamped the white connectors, remove the old probe, replaced it with the new one reclamped the connectors. Screwed it back into the range. Replaced the back and screwed that back together. It was so easy I was very proud of my self. I cut the breaker back on and cooked a can of biscuits just to see if it really worked. And it did. My bread was not burned, it was cooked to perfection.

Watched the repair video on your web site. Used the video as a step by step guide in the actual repair.