79043 - Instructions

After two failed attempts to get the 'correct' drip pans for my range from two other supply outlets, Part Select had the proper drip pans for this model. They fit perfectly! Simple installation and threw away those cheap, poorly fitting replacement pans I've put up with for three years! Thanks Part Select for having the correct parts!!

The parts came quickly. I removed old drip pans and snapped the new ones into place. A child could do this. Now my cooktop looks new and I am not ashamed for anyone to see it.

The hardest part of the job was cleaning under the old rings. Cook top looks new again!

Very easy to remove the old drip bowl and replace with new ones.

Just put the drip plates in stovetop and worked perfectly

After removing pots / pans in cabinet below cook top and turning off the power, I was able to remove the panel held by 2 screws. Pulling the old light out was just a little difficult as it came in pieces. New one popped right in, hooked up terminals, replaced the panel and that was it !!

Turned off electric at the main box. Removed glass top. Used a razor knife to pry the connections loose so that the new connections could be slid in. Problem was that the element ordered looked entirely different then the original one. Even the hookup was different. But once the connections were made, the ceramic top placed on top, and the electric restored everything seemed okay. The warmer works and when it heats up the warning light turns on. When the warmer cools the warning light goes off as it should.

Pull range unit from wall. Disconnect power cord. Remove back panel on range(10 Phillips head screws). Pull knob from surface burner switch and remove two screws. Remove and re-connect wires from switch by number on switch. Replace switch and back range panel. Re-connect power cord and re-position range to original spot.

I unplugged the stove. Then I lifted up the top of the stove to expose the burners. I unscrewed the necessary screws and plugs that attached the old burner to the stove. Then I simply put the new one back in it's place. The stove was one of those flat burner stoves, and I was a little concerned that I would be able to do it. The repair man wanted to charge me $150.00 for labor.

Our neighbor, who is an electrician, watched the video on how to install. Since this switch was substituted, he paused the video several times to see how the wires should be attached. It worked.

Reviewed the online repair video a few times then got started. Although only two were bad, I replaced all four terminal blocks. I removed the range top instead of using the built in kick stands. this left me much more room to work and I was able to clean the top of the range really well before getting started. Wires for the back terminals where short and a little difficult to use after cutting off the old terminal blocks. The terminal block mounting option for my style range included with the repair kit would not allow me to utilize the screw for the third wire on the left rear burner. I used a drill to carefully widen the hole in the mount to make the original screw fit as there are no screws included with the kit. This added the extra time to complete the repair. Over all the repair was simple to complete but having to modify the terminal block mount was dissapointing considering the web site selected parts for my specific model number. Still a bargain compared to what a service call or new purchase costs. I will be reparing my ranges from now on.

I previously replaced terminal blocks and elements so the infinite switch was the last stop before new purchase. I reviewed the online repair video. Unplugged the range and removed the three screws from the rear of the control panel. I Removed the knobs then removed two screws to release the front plate behind the knobs. I removed the two screws securing switch #1 and compaired to the new parts before removing wires. Wire locations were labled the same but in different sequence. I located the knob adapter for my knobs and set them asside. At first I thought the rod coming out of the new switch was too long and then figured out that the indentions allong the rod were to be broken off to the correct length. ( re-reading the included instructions was nearly useless - - not in plain language ) I used a pair of vice-grips clamped just below the length of rod I wanted to break off and it snapped off easily and cleanly for the most part. ( A word to the wise, this is some really soft metal at the breaks along the rod. I attempted a second break on one switch after mounting in the control panel and the thing broke off at the short end - - scary ) luckily I was still able to use it with my knobs and adapters. I relocated the switch wires to the new switch one at a time matching label to label ( L1, L2, H1, H2, P) then mounted the new switch into the control panel. I re-assembled the range and it is heating better than ever. Well worth the effort and minimal expense compared to a service call or replacement range.