66513023K111 Kenmore Dishwasher - Instructions

I opened the dishwasher door, removed the old tired seal in a manner of seconds. I measured the old seal against the new, same length, so no cutting. I started on one side pushing the seal in to the groove, made sure the seal was centered in the door. (not too long on one side or the other) It took less than 5 minutes to place the seal ... Read more and check that it was all the way in, all around the door. I wiped the door down with some cleaner, where it contacts the seal. The door was harder to close, but I expected that until it breaks in. I ran a short load in the dishwasher with no leaks. :)

took the end off and replaced it with the new one

I had a common issue on many dishwashers, the final drain cycle was not draining but the pump was trying to turn. Also, the drain pipe was clean. This issue caused a burning smell, like a circuit board heating up. Half plastic smell, half electrical. I bought a replacement pump, followed the pump replacement video instructions from PartsS ... Read more elect, and it was replaced in under 15 minutes without any tools.

The air just unscrews with one twist and the new arm twist right back on. No tools needs. Saved me $100 service call.

removed kick panel with screwdriver, 90 degree turn of screw. Put towel under drain pump. Disconnect drain hose by loosening spring clip with pliers to provide access to pump. released spring clip on old motor while turning counterclockwise to separate pump from drain reservoir. inspect drain reservoir from inside machine to remove any fo ... Read more reign objects. Installed new pump by indexing attachment flanges to notches in reservoir and turning pump clockwise until locking tab makes audible click. reattach drain hose insuring hose is contacting "stop" ribs on drain hose pipe. Run wash cycle on machine to insure there are no leaks. Re-attached kick panel.

Pull dishwasher out a few inches. Disconnect spring from plastic connector with long nose pliers. Remove connector. Replace friction sleeve. Replace connector.Reconnect spring to plastic connector. This completes repair.

Ordered a new pump (after a online diagnosis). Followed the instruction video on the website...also took the time to replace the discharge hose due to residue buildup...tested dishwasher (one cycle). Slide dishwasher back into opening....DONE. Works perfectly. THANKS

Following the video was quick and easy. Without the video it would have been slow and painful.

The old filter simply unscrews and the new one screws in.

Followed directions from YouTube video.

I took the valve off and actually hooked 110 volts to the vale and tried to blow through it and it would not let air pass through it. I replaced the the new valve in about 15 minutes and it works fine

The repair was straightforward. The hardest parts were pulling the dishwasher out from the counter and keeping the dishwasher from falling forward when I needed to reach inside. The instructions in the video were accurate. I was very glad I bought the rubber washers, because I could not reuse the washers from the original heating element. ... Read more Easy enough repair to do on your own.

Pulled washer out far enough to put 2x4’s under front feet. Removed front panel, I clipped wire connector and unplugged it. Pushed plastic locking lever in and twisted unit counterclockwise. Wiped inner rim and reversed above procedure to assemble.

I broke it accidentally while trying to get it off and it would either not spin or fall off. I simply removed it out of the box and put it on. 2 turns to the right and I was done!

Rubber friction sleeves on each side of the door provide resistance to prevent the door from quickly opening when unlatched. Over time the friction sleeve may crack and fail. Two friction sleeves are required for repair. Install a new sleeve on each side of the dishwasher door near the spring connector at the bottom.

Open dishw ... Read more asher door.

Remove the screw from the left and right bracket at top of dishwasher door opening. Brackets secure the dishwasher to the countertop.

Gently pull the dishwasher forward to expose the door spring on each side of door at bottom.

Unhook the plastic spring connector from the left door spring hook by pulling the connector slightly forward and lifting from the door spring hook. Remove the old friction sleeve if still in place by sliding over the door connection hook. Discard the old sleeve.

Insert the new friction sleeve over the door spring connector hook and push until the friction sleeve is in position completely past the spring hook. Reconnect the plastic spring connector to the door hook.

Repeat for right side of door.

Close and latch the dishwasher door. Unlatch the door. The door should remain in the nearly closed position held in place by the friction sleeves.

Slide the dishwasher back to the original position under the counter top.

Insert the screws in the top brackets to secure the dishwasher.