59677533702 Kenmore Refrigerator - Instructions

Removed glass shelf and inserted plastic running bar for drawers

Checked compressor with amp meter, and found it was not running, found Overload Switch bad.
When removing old switch watch carefully which lug you move wires from, so you will know which
lug to put the new switch on.

BE SURE YOU KNOW SOMETHING ABOUT
ELECTRICITY!!

last time i tried it right away after removing from shipping box.. relaxing with with hot air gun... was not to easy... this time i allowed gaskets to relax for a week on a flat surface. in a warm room.... took less than 5 minutes per door.... no hot air needed.... VERY easy.

I replaced both side. The left side I very easy to replace. It has 2 screws holding the end cap in place and the tracking has 2 screws holding it in. Undo the 4 screws and put the track on the new end cap and then you are good to go to install the new end cap on the left side. Now for the right side is easy, but you now have to also undo ... Read more 2 screws and other 2 for the track just like left side but also you are going to have to undo the humidity control stuff and put it on the new end cap.

It took longer to empty the items off the shelf than it did to do the repair. Slid the veg, drawers out, set them aside.Took glass shelf out set it aside. removed three screws with 1/4in socket. Removed end cap. replaced with new end cap, replaced screws, cleaned and replaced shelf and drawers. Was a very easy task. these pegs break very ... Read more easy, this is the second time I have had to replace the end cap, both times it was the left size. problem is you have to buy both the left and the right side together,

This grille just snapped into place without the use of tools. Couldn't have been easier. And the delivery was super fast; I ordered online one day and the item arrived the very next day.

The broken one just popped out and the new one popped right in! This company shipped out the part I needed immediately I had it in two days!! I highly recommend them!!

took out the drawers and glass shelf and unscrewed the sides took parts for drawer glide off put them on the new part reinstallled saved $110 service cll and $20 on the part!

Removing the old pieces & figuring out how to separate the front trim so it could be reinstalled on the new frame took the longest! (released the securing tabs with a screw driver). Reinstalling the new parts were straight forward, "no problem". (epg)

followed instructions and used common sense and the salesman was very helpful and knowledgeable and he contributed a lot of help in finding the right parts that fit

Two phillips head screws out to remove drawer slide. Three screws to remove right side drawer support. New support placed, new lid snapped into place. The right side has an adjustment lever. Re-routing that took the longest. The arm had to be removed and twisted to get the adjustment knob off and on.

****Make are you order Capacitor & Starter relay too (we ordered separtely so had to pay shipping twice)**** Super easy just open access panel on back near compressor and remove retention clip with fingers, remove & replace both capacitor & starter, put clip and acce ... Read more ss panel back on, plug in and allow 8 hours to cool! Works like new again! Hope it goes another 10 years

I ordered the part and it arrived in about 5 days. I removed the two lower crisper drawers and the glass shelf seperating these from the Wide-N-Fresh compartment, to give me room to work. I removed the two screws holding the right side endcap in place. The temperature adjustment mechanism was a bit tricky to remove from the broken endca ... Read more p and replacing it on the new endcap. Once that was figured out everything fell into place and the lid was snapped into place and worked properly

Receive part in two days. Super fast.
Repair was very easy. Whirlpool designs so even the "average joe" can fix it. Took abour 20 minutes to repair. Even with no directions.

this pantry lid was warped when the fridge was new. tolerated it for a while finally it cracked then worked pretty well for a couple years until the RH hinge pin (part of a support for the pantry door)broke. I had never bought parts from partselect.com before, but I have in the past bought repair parts from other sites. Partselect.com ... Read more had drawings of the refrigerator parts that although were a little hard to see were adequate to tell what parts I should order. I ordered the parts, they came in after an acceptable wait. The parts were literally perfect, went right in, and everything is working quite nicely. I am happy with Partselect.com and will probbly go to them first in the future. I actually like the refrigerator a little more now than I did when it was new.