59667253602 Kenmore Refrigerator - Instructions

The part just snapped in. super easy.

Pulled out broken parts and snapped/ pushed into place new ladder hooks 15 min max

Complete replacement of the plastic drawer.

Lifted up the refrigerator to level it.

Remove light lens by pushing straight back (needs some oomph, but not too much). Remove control housing by prying spring clips in back of housing with thin screwdriver or knife. Remove old control board by releasing plastic clips on both sections and removing 2 wiring plugs. Be careful snapping new control board in ; the alignment of the 4 switches and the 2 readouts is critical - easy to hang up a switch. Snap the control housing back into place, making sure that it is all the way in. Position the light lens so that it is lined up and about 1/2" back and then slide it forward (toward you) into place. The instruction sheet calls the refrigerator section the "fresh food" section. There are 2 light switches, one for each door. Both have to held down to get light to go out and enter programming mode. Easiest to close the right door, then push left door switch and quickly push the freezer DOWN button 3 times. Follow the instructions to set the program on the display and then push AND HOLD the freezer DOWN button until the display starts flashing. Release the freezer DOWN button, close the doors, open the doors to check. Display will indicate two 4s. (that was what mine indicated). Done.

Just slipped it in. I think it's a very poor design.

DEFROSTED REFRIGERATOR COILS, BUT DIDN'T REPLACE THE GROMMET.

Icemaker quit working, so replaced ice maker...was still not working, so realized it was the water inlet valve. Pulled fridge away from the wall, unplugged electrical, removed one screw from old water inlet valve, removed it, unplugged electrical connector, cut one inch of tubing going into inlet of new valve (per instructions). Put back in place, plugged in, and now making ice again. VERY EASY!

I replaced the Control Board...
the two boards need to be installed first . than plug in the connectors
(refrigerator was unplugged of course.!) i plugged in the connectors first. and had to disconnect them. install the boards first. than plug in the electrical connectors.. strange for a day or two it still did not work properly and than one day. it started working ok 7 on the freezer and 3 on the refrigerator. I do not know why..

Super simple following the instruction video you posted. Thanks!

I looked at a video on YouTube that described how to check if the water inlet valve was working. By using an ohm meter, it indicated the water valve was bad. I could hear the ice maker trying to make ice. I ordered the part; it was shipped that day. The email confirmation also had a video on how to change. I watched and changed it out quickly. The valve is easy to take out by disconnecting the water line and quick disconnect electrical line. (Turn off water and unplug unit). I took pictures of my steps so I could remember the valve orientation. The new valve went in the same way in just 2 minutes. I needed a 1/4 inch nut driver.

We had a full ice tray in 24 hours.

Our freezer door handle popped off and I learned how to put it back by watching a YouTube video.

I am not handy at this type of repair but this was a great experience. Thank you!!

I came across this site and looked at the diagrams. Instead of buying a new crisper bin frame, I noticed that the crisper bin frame was missing the frame brace. I purchased the frame brace and installed it in the crisper frame, which was easy to push into the slot. This solved my problem. No more sag!!

Unplugged refrigerator,cleaned out freezer.Removed shelves in freezer compartment(that took some figuring to unlock sliding sheves)Our freezer is on the bottom.Removed four screws from back cover to expose fan,removed screws and attached wires.Carefully opened plastic clips after pulling fan off shaft.Replaced old motor after reattaching rubber seals.Closed clips to hold motor and placed fan back on shaft.Reattach wires and screws. Put cover back and replaced shelves.Plugged in refrigerator and wallah refrigerator part was cold again!

Unplugged fridge
Pulled light cover off
Used screwdrivers to press in on tabs holding control board cover.
Unplug wiring harnesses.
Snapped board in two.
Install in cover
Reattach wires
Done

I followed the video provided by PartsSelect and it was very good with almost every step you take. Pay particular attention to how the demonstrator stands relative to the frame and things will go a bit easier. There is one thing the video fails to do well and that is show you how the metal U-shaped rod is extracted. At best, the close-up gives you a clue rather than a sense of what is done and the verbal explanation of what it is you are trying to do with the screwdriver blade is unfortunately not detailed enough. I experimented as best I could with varying degrees of force and various positions but was taken by surprise when the rod suddenly was free and slid half-way out of the old frame. I still am not clear in my own mind what I did to free it, though I have my suspicions ;). Other than that step, the video took me through everything smoothly. One key - save everything from your old frame, you'll need it all!