58714013400 Kenmore Dishwasher - Instructions

I took out the four screws that hold the front plate on and removed the latch/switch combo. Two screws hold that on, so i removed them and disconnected tthe wires. Put new assembly in place, reconnected the wires and put it all back together. Case, and door, closed. By the way, getting my part from PartSelect was very easy.

took the door off after several failed attempts, which is easy to do - 2 scews. Then it was easier to find the channel the gasket fits into.

For all Frigidaire diswasher owners, after taking the door off, I realized it was the seal around the soap dispenser that was leaking, due to stripped screws, not the gasket. I rigged it w ... Read more ith silicone caulk, but may have to replace that - looks easy, .

Removed screws and put new bottom gasket in old one just fell out.

Snapped the new one on

Old pump impeller (internal to pump/motor part) snapped into place, but snapped out of place after warranty.

Disconnected power. Removed bottom spray arm and strainer. Siphoned out remaining water. Removed hoses and two mounting screws on pump. Removed wires. Removed pump.

Installed pump in reverse steps.

pulled the old part off (no tools required) and snappen on new spray arm

Remove old spray arm and pressed the new part into place. Let the dishwasher run and the load came out very clean. Overall very pleased.

PartSelect provided the perfect place to order the parts I needed. Illustrated parts breakdown on PartSelect was excellent and the correct part(s) were identified and ordered with no difficulty. I would recommend PartSelect to anyone.

Found your website, red the reviews, followed the simple instructions provided by others that had had the same problem and repair was complete in less than a minute. No tools needed. I am a handy girl and tackle a lot of repairs/projects, this is the first time that the job was actually easier than stated. Thanks for providing a good p ... Read more orduct, at a decent price WITH LAYMAN INSTRUCTIONS!!!

I foloowed the others who repared the same item. I really appreciated their help and input. The only thing I would add is when they said that you only have to remove the bottom 2 screws on the inside of the dishwasher door they are absolutely correct. But don't look on the very bottom of the door like I did. They are on the inside of the ... Read more door, facing inside. The bottom screw on each side. Thanks for all the help.

It is rather easy to repair. After you remove the screws that secure the top of the dishwasher to the countertop you can slide the disherwasher out far enough to gain access to the hose. The hose pulls off after you slide the spring clips down the hose far enough so they no longer grab. Then simply reverse the order and you're done. Less ... Read more than 30 minutes and you should no longer have to hand wash your dishes!

#1 rule, make sure you valve off the water before removing any hoses. Remove wire trays inside dishwasher and then pull out dishwasher far enough to disconnect water line and power cord. Remove center piece and screen covering sump inside the dishwasher. Turn dishwasher on its side and remove hoses to sump and pump. Disconnect power to su ... Read more mp pump. Loosen retaining nuts that secure the sump and remove. Replace old gasket on sump with new. Turn dishwasher upright. Be careful with placement of new gasket when reinserting sump so that the gasket doesn't come out of position and the sump is centered properly. Secure with retaining nuts from bottom. Reconnect power connector and hoses to sump. Pour enough water into the dishwasher to verify gasket doesn't leak... look with flashlight under dishwasher for signs of water dripping from sump. Reinstall screen and centerpiece in sump inside the dishwasher. Reconnect water line and power cord. Run through wash cycle while monitoring for leaks under dishwasher. Reinstall wire trays.

Piece of cake as long as you get the gasket installed properly and the sump centered correctly... do not overtighten the retaining nuts or it may force the gasket out of position when the screen is secure with the center locking piece over the sump.

I went to your website found part# and parts diagram and ordered parts . I picked standard shipping . That evening e-mailed me they were instock and shipped also gave tracking # thet parts were here the next day.I removed the front dec panel then the 4 nut& bolts holding door to hinges(with door in closed position).Then I removed the 2 s ... Read more crews holding the hinges to the frame/axle. Replaced hinges with new ones .Put screws back in frame/axle . Put 4 nut and bolts back to secure door to hinges . Then i reinstalled under counter put new wheels on lower rack . I then filled it with dishes and ran a long cycle checked for leaks THEIR WERE NONE!!! THANK GOD !! Job complete, Thanks parts direct for a well designed website and detailed pics and parts#. TIM

The repair went very easy. Just opened the door , and pulled out the worn seal. Lined up the new seal and carefullly pushed new seal into place. Seal pushed in very smooth.

I pulled out the internal filter and assorted washer parts. All in good shape. I bailed out the washer and removed the pump assembly from under the washer. I pulled it apart to inspect impeller. all looked fine. Plugged pump in and turned on pump cycle. Pump did not operate as it should have and I ordered new pump. My daughter put it bac ... Read more k together and all is working well now!