57441DCWW General Electric Washer - Instructions

On Friday the 13th, after spilling my coffee all over the table, I put the tablecloth in to wash. When I pulled the tablecloth out of the washer & put it into the dryer, I must have been angry at myself because I wrenched the dryer "Start" knob too hard & broke the knob off! I spent a few minutes looking for the part, and found that PartSelect had exactly what I needed at a very reasonable price. Once ordered, I received order confirmation, and, amazingly, the part arrived at my home in less than 24 hours after I broke the knob! Thanks, PartSelect!

Only took 2 days to ship. Took the screws out of the bottom rear panel to gain access to bottom of tub. Next pushed the two hidden tabs with flat screwdriver in the front to gain access to the top of tub, they are located straight inline with each side of the washer lid in seam between the top panel and the front side panel of washer. Then installed the new suspension rod and reassembled. You can find online videos that show how to disassemble appliances if you're not sure how to get them apart for repair. My first appliance repair was easy to do and saved a lot of $$$ vs paying for repair or purchasing a new unit.

Basically, I just followed the instructions in the video that is posted on this sight. It went off without a hitch. Removed the screws from the control panel, lifted it up and out of the way. Then I used the putty knife to release the clips that hold the front panel in place and then removed the top of the washer. Pretty easy from there to swap out the dampening straps and reassemble the washer. Saved a lot of money doing it myself.

Drain tub. remove 2 hose clamps and hoses. R&R 2 screws that hold pump.

Reviewed your website for problem symptoms for top loading washers not agitating and possible solutions. Purchased the lid switch wiring harness. All I needed was a painters 1" putty knife, wire cutters, Philips head screwdriver, (2) electrical connectors (crimping type), crimping tool, and electrical tape. Very easy installation and problem was solved. Recommendation, the wiring harness should come with electrical connectors (crimping type). The installation video on your website was a big plus in making this small project a success

The cap just removed by tapping a few times with a screw driver and hammer. then pulling upward it came off and I placed the new dispenser on. a couple minutes saved me from running up and down to add softener and it was very inexpensive.Thanks alot PARTS SELECT.

Took front panel off the washer and found the pump working but no water drained from the tub. Took the motor off the washer by removing the two 10mm screws and attaching hoses. Decided to take the motor apart and found the propeller shaft has broken off inside the pump. Ordered new motor from Partselect and replaced it. Washer is working fine now.

It was almost a complete tear down. Most difficult part was discivering how to remove the front panel. Slip a putty knife between the top and front covers. push and depress the spring tab on each side. The left hand nut on the hub was difficult. I had to get a neighbor to hold a large pair of pliers while I put a pipe wrench on the nut and hit it with a 2 lb. hammer in order to break it loose. Puting it back together do not forget to reconnect the level sensing hose to the level selector, I did. Machine will not perform without it. You can do it! I did.

pulled off cup on top of agataor. scrwed off nut. pulled off agatator. flipted up side down. took off agatator bell wich is on the bottom of the agator. sliped on bell. put agatator back on and scrwed on nut. dont reamber the size of the nut.sorry. put cap on and your done.

First off, the repair part arrived in only two days. The schematic was very detailed and accurate on your web site. Once the part arrived and removed from the bag, it was a snap to install with just a needle nosed pliers. Total time was less than 5 minutes. This was the first time I had used PartSelect and you can bet I'll be back. Thanks again. Gary K. in IN.

Remove four screws which held the front cover of the washer. Dropped the cover down to expose the temp. switch. Turned the switch 1/8 turn counterclockwise which removed the switch from the cover. Pulled of the four pigtail wire leads and then installed the new switch in reverse order. Very easy!!

Worse machine ever made. Installed all parts per videos .they helped a lot. Inner tub went on crooked and first wash ruined inner/outer tubs top piece. Took to dump.

The hose has a tapered end that fits in a tapered hole in the back of the washing machine.When insalled the first time,the joint leaked badly.My solution was to coat the hose end and the interior of the hole in the back of the washing machine with silicon sealant;let it set up for a few minutes and install the new hose.This solved the leak and the hose seems to be working fine now.

turned off the water and removed the hoses. Then removed the screws that held the back plate (that contains the knobs). removed the two screws holding the water valves and the hose to the washer. replaced the valve and then reassembled the rest.

removed washer front panel, top panel to access the water fill spout and hose. Disconnected and replaced.
personnel at part select were very knowledgable about detailed part and the overnight service was right on time.
I would recommend part select for your next appliance parts needs.