40-690 (Type 1) Delta Scroll Saw - Parts

This is a genuine OEM sourced component, it is specially designed for use with DeWALT and Delta scroll saws. It is an identical replacement for a missing or damaged control knob that originally came installed on a new unit. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this...Read more hardware. Keep in mind this high-quality part is made of durable plastic material and is sold individually.

This is an authentic OEM replacement part, guaranteed to fit the scroll saws listed below. This adjustable air nozzle/hose is used as a dust blower. It is connected to the bellows via the metal air pump cap. Nozzle attaches over the air pump cap's ball end. When installing this part it is recommended to heat the nozzle's connecting end un...Read moretil soft. Then just ease into place. This item is sold individually. A Torx screwdriver is used to remove the air pump cap for easier installation.

This is an authentic OEM part for use in saws made by DeWALT and Delta. The housing attaches to the control knob and the switch. During the installation process, an allen wrench might be needed to replace this part. It will need to be replaced if it becomes broken. This is made of plastic and is sold individually.

This is a genuine replacement part manufactured for use with scroll saws. The screw has a hex socket head and is typically used to secure the foot to the table. The screw is sold individually, please see model diagram for additional parts.

O-rings are made to contain thousands of PSI pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-Ring failure. The most common among power tools are: • Extrusion and Nibbling - The O-ring has ragged, tattered edges. ...Read moreThese are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • Abrasion - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that is too rough, contains grit or is too smooth to allow lubrication. • Over Compression - The O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • Heat Hardening - The O-ring has a pitted or cracked surface, and is often flattened on both sides. Caused by temperature exceeding o-ring capacity. • Weather/Ozone Cracking - The O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching (greater that 5%) causes similar cracking.

This is a genuine OEM sourced clamp that it is specially made for use with DeWALT and Delta scroll saws. It is a standard hardware which has multiple applications based on the model of your unit, please make sure to refer to the appropriate diagrams of your model for the correct location and use of this item. This high-quality clamp is ma...Read morede of durable metal and is sold individually. Keep in mind the screw is sold separately.

This fuse is a high quality part sourced from the original manufacturer for DeWalt and Delta scroll saws. The fuse is a safety feature to prevent an electric surge from overloading the motor. Once the fuse is tripped it will burn itself out, and will need to be replaced. This part is sold individually, keep in mind the fuse cap is sold separately.

Genuine DeWalt replacement part Includes 1 Carbon Brush with wire lead and brush spring attached. • Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power ...Read moretool components. • Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. • Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. • A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. • When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.

This item has been sourced from the original manufacturer to be used with scroll saws from DeWalt and Delta. The washer is used to provide spacing between the bolt and the blade chuck. This item helps keep the bolt fastened and to the chuck. The washer is sold individually, please note two may be needed.