36314475792 Kenmore Dishwasher - Instructions

Remove two front mount screws from counter top
Lower dishwasher floor feets
Pulled electric leads cover and disconnect electric leads
Pulled dishwasher out and leaned on it's back
Sorry missed a step turn off breaker to dishwasher
Removed water line and drain hose
Removed motor/pump using only a socket setup ... Read more and cross tip screw driver
Installed new motor/pump using same tools as removal
Stand dishwasher back up push back into space and reconnect all item mention in removal
Turn back on breaker
Ops check dishwasher
Done.

Only getting "humming" sound from dishwasher. Although water had filled the dishwasher tub, pump/motor would not operate. After some research, figured the motor had siezed and I had to replace the pump/motor assembly as mentioned on this site. The kit came in a couple days and I reserved a Sunday afternoon for the repair which I had neve ... Read more r done before. Hardest part of repair was unhooking and removing dishwasher from under counter and then getting it back in proper place. I would suggest providing some instruction within the repair instructions showing how the dishwasher is installed or how to remove it as I had never installed one so I was not quite sure what screws etc I needed to remove on the dishwasher itself to start to remove it? I was able to find the original installation instruction for the dishwasher and found that all you had to do was remove two screws from the inside top of the dishwasher which were securing it to the bottom side of the kitchen counter and then the whole thing just slides out. Once removed, turned dishwasher over to access bottom where pump/motor is located. After determining which diagram to use with the instructions, proceeded to replace the motor/pump assembly. It came out easily after wrestling with some corroded bolts/nuts and the existing pump inlet and outlet hose clamps. Mine were old and worthless and no new ones (3-4") are supplied with the kit. Had to run to hardware store to get new hose clamps for the inlet/outlet of the pump before intalling new one. Suggest new hose clamps be provided with the kit. Only thing that was not too clear in instructions was when reconnecting power wiring harness to motor. By looking closely at the instruction diagram I was able to locate what looked to be the right power extension harness from the bag of parts and attach it to the existing power wire harness and the new motor. Suggest also that you somehow better distinguish or identify the proper way the power wire harness should be fastned to the motor? The existing power wires were both the same color and both the female and male connections for the power at the new motor were identical leaving you to guess which wire goes to which connection. After re-installing dishwasher, put about a gallon of water in bottom of unit prior to starting and then put it through a few cycles. It has been working just like new. Suggest having a helper when removing and re-installing dishwasher from under kitchen counter to assist with the power cord, water line, drain line, and help to turn the dishwasher upside down and right side up again.

Simply screwed in new cap

Removed dishwasher, took off motor, and ordered part. It was delivered in a timely fashion (3 days). Determined which directions to follow. Used screwdriver to hook up motor. Put dishwasher back into cabinet area, made sure there were no leaks before fastening the dishwasher in place. Took about 1/2 hour to complete process. Very satisfie ... Read more d.

I just plugged in the model number and a screen came up that showed all the part numbers that made up the model. picked out the parts that we needed and ordered it and within 2 day we had the new basket that we needed for our dish washer.
the service and ease was better that going to the appliance store and picking up the basket.
... Read more />I was very happy the the service.
Donald Brown

Very simple. By hand, I unscrewed the old spray arm and screwed in the new one. One brief hangup. The old spray arm was very hard to unscrew. Rather than seeming to force it, I called the PartsSelect 800 number and got advice. The tech reassured me that all I had to to was unscrew it and put in new one. So I applied more force and old ... Read more one came out. A breeze.

Use screw driver for leveage, righty tighty, lefty loosie, easy as that, and thanks to Parts Select, ordered my part on Thursday by dinner time Friday had part, install no washing dishies by hand, Thanks guys

Brian Souza
Vacaville, CA

Replaced lower rack with new. Upper rack removed front stoppers, removed old rack, slit new rack in and replaced stoppers. Total time about 15 mins.

Read directions. They were poorly drawn. Set them aside. Opened up unit on December 26th. I made careful observation of the wiring, two hoses, one metal bracket, the hose two clamps, and then proceeded. Instructions said 1 to 2 hours, to complete. Ha Ha, perhaps if you've done it before. It was actually really closer to four hours. ... Read more When done, it worked perfectly. The best part, my wife said: "This was the best Christmas present ever!" That made my day! Dishes are clean again, just like new! Thank you: www.PartsSelect.com.

Ordered the new motor/pump here at parts select and with the easy directions I replaced in no time flat. Saved me $300.00 for a replacement.

Pop the end caps off the slides by pushing the lock tab in with a medium flat screwdriver, through the square hole in the side of the slide. Pull the rack out and set it on the counter. Pop the axles off, with the rollers, with your fingers. They are just clipped on to the rack wire. Pop the new ones on 4 places, fingers only needed to cl ... Read more ip them to the wire. Put the rack back in the dishwasher by aligning the rollers in the metal slides and pushing it in like normal. Pop the rack slide end caps in by just pushing them in. If you're smart you bought new ones, they're cheap insurance. Save any good used parts in your kitchen junk drawer for the next time you treat it rough. Less than 5 minutes to fix. So easy a caveman could do it. One just did!

I first made a bad assumption that the leaking dishwasher was from the gasket. I replaced the gasket and it still leaked. To find the leak, I took the body off of the dishwasher and ran it to find the leak. It was from the solonoid connection. I took photos of the leaking motor unit and very easily replaced the new motor unit by matching ... Read more the placement from the photos. The hardest part is tipping the dishwasher on its side and mopping up the water.
It was very easy. All you need is a nut driver and a Phillips screwdriver. Even an over-domesticated, non- tool user can do it.

over time the upper rack axles broke so the rack would just come out of the rollers. I ordered the parts from here and had to youtube how to get the stops out so I didn't have to unscrew the metal guides out making an easy job into a hard one. all you have to do is with a flat head screw driver is slightly bend the plastic end part of t ... Read more he stop which is in the metal guide that stops the wheels from coming out of the guides. once you bend out the plastic end you then turn the stop to get it out of the metal guides. if you youtube it its very easy. just be easy when you bend the plastic piece because I can see it breaking. I didn't break mine so the job was very very easy and took all of about 5 to 10 minutes to complete the entire job. I love this site it had real life info to help out when you need to do a job and trouble shoot your appliance.

Determined not to call a repairman for such a simple problem, I watched your extremely helpful video. The ordered parts came right away and all it took was a screw driver and 30 minutes to take off and replace four rollers. So easy, this 75 year-old grandma could do it!

According to instructions with part