36314475792 Kenmore Dishwasher - Instructions

The lower dishrack just lifted out and the new one placed in. The upper rack had stops at the end of the slides which could be removed with the help of a flat blade screw driver, old rack slipped out, new rack slipped in and the stops replaced on the end of the slide which keeps that upper rack from coming al the way out of the dishwasher ... Read more . There was a link to a "how to do video" on the email order confirmation. It just gave me reassurance that I could easily do the job.

Ordered rubber connector and it arrived the next day. Shut off main power and water. Disconnected water supply and pulled unit out from under counter. Flipped unit over on it's side. Disconnected wiring, drain hose, clamps and completely removed motor/pump. Rubber connector would not unscrew by hand so I found a drinking glass slightly sm ... Read more aller in diameter than the connector inner diameter. Inserted glass in connector and proceeded to unscrew connector by turning connector and glass together. After removing old connector I cleaned the mating part after removing it from inside the washer and removed all the build-up. Replaced everything back in same order.

Unplugged unit, unscrewed screws on top of dishwasher attached to countertop, undid water supply and drain hose that goes into tee with garbage disposal. Using crescent wrench turned front leveling screws up all the way and slid/rocked dishwasher out from under the counter - I had no problem leaving back leveling screws down. Turned dishw ... Read more asher over on some towels (it WILL leak some water so spread out some towels!) so it was oriented like the directions that came with pump and motor. The directions were good, although color or a picture might have been more helpful. CHECK the new pump/ motor unit CAREFULLY for any loose debris from packing etc. I had a small piece of plastic that was in the top of the motor that goes in the dishwasher bottom that rattled around after I installed everything and put it back. I was able to get to it from the drain assembly in the tub but it made a heck of a racket at first. All in all, I had a great experience. I'm glad I ordered the pump and motor even though I only thought I needed the drain solenoid because when I took the old unit out, the prop on the old impeller was almost gone. Easy to order, good customer service (I called with a question and talked to a wonderful customer service representative!), good directions and easy to do. I'd say a 4 out of 10 in terms of difficulty. Thanks PartSelect!

I disconnected the electrical wires. Then disconnected the support strut and the two hose clamps. I was then able to remove the motor /pump assy where I completed the disassembly of the solenoid linkage and pump assy. I removed the solenoid shaft seal. I disassembled the impella parts & the motor shaft seal. I reassembled using new se ... Read more als, impeller, and grader nut. The only tricky step was waking up to the fact of a left handed thread on the grader nut. I re-installed the motor/pump unit, tightened the hose clamps, connected the electrical wires, & support strut.

Inserted wheels on socket and then into the dishwasher rack.

Removed old rack replaced with new one which was an exact duplicate. Mama's happy; everybody's happy.

We knew roughly how we needed to put the cap on the rail, but our technique of simply forcing it in the end of the rail wasn't working. The trick is to bend the moveable part of the plastic cap inward while you're sliding it in, and it clicks right into place.

The location of the cap we were replacing was the upper back left, w ... Read more hich made it a little tricky to reach back there and insert it, especially for a bigger guy like myself. We took the bottom rack out and my smaller wife was more easily able to lean in the dishwasher and reach back there to insert it.

First I opened the package and screwed the new dispenser cap into place.

installed part on inside end of rail. no tools needed. original part wouldn't stay on rail. finished in 2 minutes
wife happy

Removed the lower rack and installed new wheels with clips

The newly purchased wheels have a little different design and could be installed in a matter of few seconds.

first I used a shop vac to clean any excess water left behind, removed the sump housing from the motor, removed the sump housing from the body of dishwasher, replaced the old housing for the new one and reversed my steps to remove old one,

Disconnect water line and screws (2) holding dishwasher under cabinet, and clamp for wastewater line. Pulled dishwasher out, turned on its side, and removed pump. Disassembled pump per instructions (great instructions) and installed new parts. Reversed to reassemble and except for a loose clamp that leaked (I tightened) it went well. ... Read more Just under 1 hour.

Just put the part on.

Remove two front mount screws from counter top
Lower dishwasher floor feets
Pulled electric leads cover and disconnect electric leads
Pulled dishwasher out and leaned on it's back
Sorry missed a step turn off breaker to dishwasher
Removed water line and drain hose
Removed motor/pump using only a socket setup ... Read more and cross tip screw driver
Installed new motor/pump using same tools as removal
Stand dishwasher back up push back into space and reconnect all item mention in removal
Turn back on breaker
Ops check dishwasher
Done.