36262 Kenmore Range - Instructions

I UNPLUGGED THE WIRE, ASSEMBLE THE BURNER ELEMENT KITS
LIFTED UP THE SURFACE BURNER PANEL,
OPENED THE BACK RANGE COVER,
UNSCREW THE NUT HOLDING THE BURNER CONNECTOR, DISCONNECT THE REPLACEMENT WIRES ON THE BACK PANEL
TRACE THE NEW WIRES CLIPS TO THE BACK PANEL & TIGHTEN THEM WITH EXISTING NUTS
SCREW THE OTHER EN ... Read more DS BACK WITH NUT HOLDING THE BURNER CONNECTOR

I unhooked the main power cord, unhooked the worn out block terminal cut the tape that was holding all the wires together. Removed the back panel and followed the wires unhooked the 2 wires and installed the new block terminal. Tied all the wires back, attached the back panel and plugged the power cord back into the outlet. i tested the b ... Read more urner to see if it was working. The burner is working great, instructions were easy to follow and my wife is happy. Thank you

Pull out stove. Unscrew wiring from burner holes. On the back take off lower panel. Take off upper panel. Unscrew end caps from control panel. Take off all knobs. Carefully lift panel up and over the top to expose pivot pin. Unscrew pin from stove top. Remove stove top. Reinstall new one in reverse steps.

First and foremost I read each of the blogs from your site from other people who have repaired this part. It was great.
First I unplugged the stove. Removed the back plate of the stove by unscrewing 6 screws. Removed the heating element & drip pan. I lifted up the stove top to examine the receptable, and removed the receptable hel ... Read more d in place by a single screw using the nutdriver.
Once it was removed, I cut the wires attached to the receptacle with pliers. I screwed on the new receptacle, and taped the new wires to the old ones which led back to the back panel where they were attached to the switch.

By doing so, I was able to easily lead the new wires to the back side of the stove panel. I removed each old terminal wire and replaced it with the new one. (I had read in a previous blog that the polarity of the new wires didn't matter). I replaced the drip pan, and heating element, turned the switch and everything was working just great! I replaced the back panel, and that was it!
As you probably can guess I have never attempted to repair any type of appliance...ever! But your website and the people who shared their stories empowered me to do the job. Thanks so much!

Since we got the stove,this is the second time we've repaired these connectors. The first time the connectors came with pre-stripped wires, wire nuts and heat shrink tubing. This set came with pre-attached spade terminals, so I had to crimp the mate to the wires in the stove then put heat shrink tubing on the splices. I also had to bend ... Read more the part of the connector that mounts onto the stovetop. These had a horizontal tab for the mounting screw rather than the vertical design that our ranges uses. If the connectors designed for the earlier model were available, it would simplify installation since shrink wrap and wire wraps came in that kit and the mounting bracket would fit correctly.

Unplug the range before opening the back panel and removed the wiring connection and replaced with the new one

First I found the model number, but it's parts were under a different number. So I ordered what I thought was the right oven element, but it wasnt right . My husband couldnt get it to fit . Well he finaly found the right part number so we could order the right part. We returned the wrong part and got the right element. It went in per ... Read more fectly and the oven is working just fine now. Remember to always look up the part number you need and then order it.

Removed burners and existing drip bowls and installed new drip bowls and existing burners took approximately 15 minutes

Just have to remove the old kit and replace it with the new one. No tool required.

Move range out from wall,unplug power supply,remove two screws from back wall of lower oven element unplug two wires,discard burned element.Install new element,plug two wires in,fasten two screws. Done

just lift the cover and put it on.less than 1 minute.

First I removed the burners and pulled the stove out to get the back cover off. Removed the back cover after main power was shut off. Removed old burner terminal blocks and replaced with new ones. Replaced back cover and pushed stove back into place. Turned on main power to stove checked burners and they worked. DO NOT REPLACE OR DO ... Read more ANY ELECTRICAL WORK ON ANY MAJOR APPLIANCE WITH OUT FIRST TURNING OFF THE MAIN POWER SOURCE.

I just lifted the old part and dropped the new one in. Everything fits perfectly. The new flame is a beautiful blue color.

pull out, push in

after removing element.I order part. part was inserted without problems . It was correct fit. I am now baking again. Thank you the quick services on the order.