Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
someone sat on cooktop and dented it
3 of 5 peoplefound this instruction helpful.
Daniel from Osseo, MN
Easy
15 - 30 mins
Nutdriver, Screw drivers
took off burners, removed screws one at a time, only tough part was getting to grounding screw so i took off back plate (easy) to get to grounding screw. i recommend doing it all at once with no break so you remember where screw went, or mark them with sharpie. it was fun once i got started. good experience and now it looks like new. plus
... Read more i didn't have to clean the old one.
Read less
Was this helpful?
Thank you for voting!
The burner would not turn off and I or my wife would have to turn the breaker off.
2 of 2 peoplefound this instruction helpful.
Mark from WOOSTER, OH
Really Easy
15 - 30 mins
Nutdriver, Screw drivers
I simply turned the power off and slide the stove forward to give myself room to get behind it and just unscrewed the cover behind the burner switchers and pulled the switch knob off then I removed the two small screws that hold the burner switch to the control panel and go to the back and pull the wires carefully and replace them on the
... Read morenew switch one by one and screw the new switch to the control panel and replace the back panel and done!
Read less
Was this helpful?
Thank you for voting!
Broken drawer glider
2 of 2 peoplefound this instruction helpful.
James from RANCHO MIRAGE, CA
Very Easy
Less than 15 mins
Screw drivers
Took off broken part and replaced it with the new part by removing a Phillips head screw, the broken part, replace with new and reinstalling the same screw.
Took it out of the box, lifted the stove lid and replaced the part, no tools required. Very satisfied with the shipping and the part, great service. Thanks!
Was this helpful?
Thank you for voting!
Needed New Burner Bowls
2 of 4 peoplefound this instruction helpful.
Carolyn from Garden City, ID
Really Easy
Less than 15 mins
Removed the old burner bowls, replacing them with the new ones.
All I did was remove the old burner and put the other one on. Took less than a minute.
Was this helpful?
Thank you for voting!
Burners were old and dirty
1 personfound this instruction helpful.
Chris from MUNDELEIN, IL
Very Easy
Less than 15 mins
Simply removed old burners. Placed leveling nuts in place. Replaced new burners in place.
Was this helpful?
Thank you for voting!
Wanted new burners for 24 year old gas range.
1 personfound this instruction helpful.
Victor from LIMA, OH
Very Easy
Less than 15 mins
Simply took out old burners replaced them with new burners, no tools needed.
Was this helpful?
Thank you for voting!
oven racks old and ugly
1 personfound this instruction helpful.
Claudene from ORCUTT, CA
Very Easy
Less than 15 mins
1. Open oven door 2. insert oven racks (perfect fit) 3. close oven door. Done and finished - man am I tired
Was this helpful?
Thank you for voting!
The lower,BAKE, element had burned in half almost causing a fire.
1 personfound this instruction helpful.
Joseph from DIAMOND SPGS, CA
Very Easy
15 - 30 mins
Nutdriver, Pliers
Slide the rang out to access the 240V plug & unplugging it. Removed the sheetmetal cover from the rear of the range to access the slip on wire plugs to prevent damaging the insulation. The insulation would be damaged if pulling them through the opening in the oven wall with the plugs attached to the element. Removed the racks from the o
... Read moreven. Unscrewed the retaining screws holding the element to the rear wall of the oven, lifted damaged element out and reversed the process for instillation. Perfect opportunity to clean underneath and behind the range.
Read less
Was this helpful?
Thank you for voting!
Burner could not be cleaned any more.
1 personfound this instruction helpful.
Sherri from MORGANTOWN, WV
Very Easy
15 - 30 mins
Just lifted off the old burners set on the new ones.
Was this helpful?
Thank you for voting!
burner was not heating
1 personfound this instruction helpful.
lucille from HAPPY CAMP, CA
Very Easy
15 - 30 mins
Screw drivers
unplug it and plug the new one in
Was this helpful?
Thank you for voting!
Oven would not heat up
1 personfound this instruction helpful.
MICHAEL from MORROW, GA
Really Easy
Less than 15 mins
Nutdriver
I removed the rear lower cover. Disconnected the terminals from the heating element. Removed 2 screws from the heating element from inside the oven. Removed the heating element. Reinstalled everything in reverse order.
Was this helpful?
Thank you for voting!
Old drip bowls were badly tarnished . . . shine could not be restored.
1 personfound this instruction helpful.
Paul from PROVO, UT
Really Easy
Less than 15 mins
1) Make sure unit switches are turned off. 2) Lift Calrod unit up and pull it from electrical receptacle. 3) Withdraw Calrod unit from old bowl. 4) Insert Calrod unit through large hole in new bowl. 5) Push Calrod electrical connectors into receptacle under range top. 6) Seat Calrod unit on bowl rim and insert the assembled Calrod un
... Read moreit and bowl into the hole in the range top.
My Orders
