2DWTW4845EW0 Whirlpool Washer - Instructions

I was able to look up the issue on Youtube and watched a few videos and was able to complete the repair with help of my daughter. It was little hard to do but you do need gloves with a good grip when taking the rods out of the washer, but putting the new ones in was very easy.

Once I replaced the suspension rods, there was a little shaking but not like before. Very quiet now, no crazy loud banging

the first order was ordered wrong for me and the part was to big so I had to send it back and order another. The second dispenser was the right one and went on well to the machine. Just had to put it on the machine by hand.

The installation was very easy and took me 45 minutes to complete by myself. I put the washer on two cinder blocks and then removed the lid. I started with the suspension rods that were closest to me and they were really easy to exchange. When I got to the rods in the back they were a little more difficult because there was more tension with the new rods installed. I used the old rods to hook and pull the new rods into place and it was overall very easy.

Youtube has videos. It's very simple just replace one at a time.

I did the repair just as the video showed, and had no problems at all.
the hardest thing I had to do was to move the washer out to where I could get to the back of the machine.
Due to the help of the sales rep and the video the repair was very easy

Thanks
Louis

unscrewed a bolt, pulled top agitator out and replaced parts and reinstalled.

I unscrewed the top panel of the washer. I lifted up the top and used the pint scrapper to loosen up the lid switch and slid it out. I pulled the switch wiring harness out of the rear top of the washer. I slid the new lid switch and wiring harness back through the opening and secured the switch in place. Screwed it back in place. Took less than 15 minutes. I followed the instructions on the video, easy peasy lemon squeezy.

Watched video from partselect and it was on the money. Removed a few screws and tilted the lid. (after unplugging). Pulled it out from wall and tilted machine to have access to bottom. Had grandson reach from underneath and pull the rods out and inserted the new ones. Work great now. My wife is happy and I saved about $600 because I didn't have to buy a new one.

Used your exploded view of the area to determine the problem-found the broken part and reassembled following the drawing. I felt like a pro after a test and kept my wife happy. [only lost a few days waiting for the parts which arrived as expected]

Nothing to it. Just remember to put the insert in the knob, NOT on the selector stem. Line up the flat part of the insert with the flat part of the stem and push the knob in place.

Don NOT ram it on the selector stem. When it's seated, don't push any more. That's all there is to it. It works. If the pointer on the knob indicates the selector is lined up correctly, but it isn't, the problem is the selector, not the knob.

I removed dispenser for softener, then pulled cap inside upper agitator, I was able to get my fingers in the grips and pull firmly to unseat it. (disgard o-ring it comes with the repair kit). I then removed the bolt from center and grabbed the bottom of the lower agitator and gave it a good tug to release the whole unit. If that don't work you can get a flat tip screwdriver between the two sections and pry up slightly. Once it was all loose I removed the upper assembly taking care to to remember how all the pieces were assembled. replaced everything in the same order and when it came time to reinstall the inner cap and seal I made sure I put the cap in straight. Also if the seal doesn't cooperate you can use a little liquid soap to lubricate it. you dont want to use grease because it could possibly get on the clothes (the softener sits in there)! You can use the tip of the screwdriver to tuck the oring in if that doesn't work but be very careful

Removed bolt holding top of agitator, removed top of agitator. Replaced parts. Reinstalled agitator. An old machine now works like a new model.

After disconnecting water lines and power, tip machine onto its back. The actuator is located under the drum. Remove the cover over the motor/ drive belt. Actuator is located by the transmission and held on by several screws. Unplug the wiring harness and remove three screws with Phillips screwdriver. Install new actuator..

I watched the PartsSelect video. I was hoping for the tub with the slots in the tub mounts, but mine didn't have them, so I had to lay it down on its back. The only thing I did that was not in the video was I placed a 2" thick closed cell foam knee pad I had on hand between the tub and the back of the housing. When I laid it down, the tub was elevated by 2". This made reaching the two rear rods a little easy. It seems that there would be a more robust way to achieve the dampening affect, but I guess this is cost effective.

It's strange that I searched for my issue several times and only saw recommendations to level the washer. It was level. Then one day I ran across the suspension rod resolution. It didn't do it on every load, but after a year of my wife nagging me and threatening to get a new washer, I finally fixed it. The biggest issue is just logistics in a condo hallway and a little leaking water. I also replaced my hoses. Should be in good shape until the next thing.....

Exactly as shown in your video