2671532210 Washer Dryer Combo - Instructions

The bracket on the part supplied was different than the original. The wire connector was also different. The bracket had to be drilled for a hole to match the original. The connector had to be cut off and the wires soldered together, then tied off to the frame to keep them away from the flame. The repair works like new but not the simple plug and play I was expecting. In all fairness the exact model number was not available, probably since the appliance was 24 years old, so I chose the closest model number with the picture that looked like what I had. Problem solved.

Took the top of the dryer off by removing two philips screws in front. Removed two screws holding the front of the dryer on. Pulled the front out enough to reveal the worn drum slides. Replaced them. Reassembled.

When I first ordered the part, I did not know I needed 4 slides for the bearing. 2 of my slides had disintegrated. Make sure you have 2 good white slides, and 2 good blue slides, or order them with the bearing, or you will pay another $7.50 for shipping.
Once I got all of the parts and put it together using only common sense, I found it was binding tight. So I realigned the back of the drum that I had messed up while I was trying to diagnose the problem.
Parts Select definitely helped with diagnosis, through this comment section.
Thanks!

First I removed the front and top panel to the dryer. I then popped of the drum bearing, popped the new one on, added slides and put the top and sides back on. Turned on the dryer and it works just like new. All for less than a repair man would come out on a call for.

I removed the 2 screws that held the top on. They are located inside the door on the upper lip. I then removed the 2 screws that held the front of the dryer in place. From there I leaned the front against my leg and the drum bearing just snapped off and the new one snapped into place. I replaced the front drum slides easily. They just slip into place. I put everything back together and it is now quiet. Very easy.

took off top of dryer, took out 2 screws so front of dryer could be removed, replaced bearing,slides and felt seal

I removed the two screws inside the door and popped the top loose. I took the top off to see and have access to the interior. I leaned the front out and inserted the belt around the drum (with my wife's help), replaced the screws and laid the dryer on it's face on a rolled up blanket and proceeded to run the belt around the pulleys (two). The drive pulley was easy but the idler pulley, not so easy. I had to figure out how the pulley arm was supposed to provide tension on the belt. I figured it out by looking at the diagram. It was then I found the idler pulley was broken and fell apart in my hand. I advise that a new pulley be installed at the same time as the belt. Everything I read on your web site helped.

Open up the unit's lid first and then removed the front panel. Then I removed the broken belt and then routed the new belt around drum, through the belt tensioner, and onto to the motor pulley. I checked to make sure the belt was securely in place and if it would rotate the drum. Once I was positive it was in place I put the dryer panels back together, plug in the dryer, and tested operation. The only thing that was difficult was trying to figure out the routing of the belt through the tensioner because the old belt wasn't in place anymore. In all it was a 45 minute job.

I removed the front cover and top of the dryer by removing screws visible from opening the dryer door. I then had to figure out exactly how the belt was set around the drum and other pulleys. With the belt around the drum and around the motor rotor, the other pulley had to be very forcibly pushed towards the drum in order to get the belt seated correctly. This being my first dryer repair, I was unsure of how the belt was needed to placed. But eventually figured it out using pictures from the internet. The second pulley required a lot of force and I had to squeeze my hand and arm under the drum of the dryer in order to make the belt fit correctly with enough slack to reach around the second pulley.

Removed top cover by removing 2 screws in front door opening. Then removed front door removing 2 screws, one on each inner side of the front door.
Removed 2 screws on side doors located about 9 inches from bottom of dryer to permit taking off drum. Slip off belt and remove drum.
Thinking I had a bad bearing, I decided to turn the dryer on and found out I had a bad motor-still functional but noisy. I had difficulty installing the new belt since there was not access panel (which was mentioned in the service manual), so I decided to take off the left side panel-about 8 screws. With the left side panel off, it was a lot easier to install a new belt and install the new front bearings. I actually did not fix the noise, since I need to replace the motor ($$$). When it goes really bad, I can order it then, and it should not take me long to replace it.

First I removed the two screws on the underneath side in the door at the top and removed the old drum bearing and installed new one with the 2 new plastic slide bearing. It was easy and I will tell all of my friends and family about the website. Service was fast and simple to order the right part. Thank you.......Linda

First I unplugged the dryer then removed the two screws just inside the door along the upper edge. Top comes right off then there is a screw holding the front on at each side. Removed the front, popped off the old drum bearing, put on the new one. The four drum slides, which you need all four are placed at the top edge of the bearing two on each upper side. Vacuumed out the inside of the dryer, reassembled and runs like new!

This dryer uses pieces of slippery plastic on a plastic support attached to the dryer front as a drum bearing. Over time the slippery plastic wears out and the underlying support will wear through like mine did.
To replace this, first unplug the dryer and then remove the two screws inside the top edge of the door opening to free the top of the dryer cabinet. You may want to remove the door first for easier handling. Next lift up the cabinet top and pull it free to expose the drum and bearings. The front of the dryer is held on with two screws at the top front corners, remove these and tilt the front forward to expose the drum bearings. remove any remaining plastic sliders and pull the old bearing support free, stating at the top and watching out for the light bulb if present. Then install the new bearing support and replace the sliders. Now tilt the front panel back into place, guiding the bearings into the drum and lining up the tabs and slots. Replace the screws, this requires some fiddling to get the alignment right, then work the top panel back into place, reinstall the screws in the door opening and replace the door if it was removed.

pulled off the top, pulled off the front then replaced the plastic that was supporting the front side of the drum. fairly easy to replace although the little plastic 'slides' (you need 4 of them)

opened the dryer door,removed the two screws under the top and removed the top. then removed the two screws that held the front panel on, removed the drum top bearing which only snapped into place chaned the 4 drum slides, whuch were old and very worn down snapped back into place ,vaccumed the lint out and then put the drum on the bearing tested it and the noise was gone ,then i put the front plate back on the the top total time was 20 minutes .and has been quiet ever since. i ordered the part online and it was here in two days . i am very happy because its the first time i ever attemted to fix an apliance on my own.