25350682000 Kenmore Refrigerator - Instructions

I removed the screws that held the the ice dispencer from the bin. I than removed three screws from the bottom of the bin. I put the new plastic piece on the end of the spiral piece that
pushes the ice. I inserted the spiral piece back into the hole. I than screwed the ice dispencer
to the bin and re-inserted it back in the refr ... Read more igerator.
It took me about 5 to 10 minutes. It's really easy!

The untwisted the water filter took out the old water filter and replaced it with the new one and twisted the cover back on. it was very easy to do and now the water tastes very fresh :) thank you

I replaced the solenoid first because the ice maker was not getting water. After replacing the solenoid valve, I waited about 1/2 an hour, still no water. So, I ordered a replacement ice maker. I then installed the replacement ice maker, waited a 1/2 an hour, still no water. Then, I waited overnight. Yeah, ice! WORD OF ADVICE. WAI ... Read more T OVERNIGHT TO SEE IF THE ICE MAKER CREATES ICE. Not sure how long a cycle takes, but it's longer than you would think. Hope your installation is a success!

Pull out the unit from the wall, Unplugged the frig, removed the lower cover panel. Remove 2 screws holding the water valve from the unit, then removed the 2 connectors that turn on the relays. Connected the connectors to the new valve, then replaced inside of unit and replaced the lower back panel cover, plugged it back in, then tested t ... Read more he water flow at the spout, and waitied for the ice maker to kick in. Worked perfectly.

Unplug fan and remove 3 bolts. I had to bend the fan frame in order to remove fan. Change fan blade and reverse procedure. Fridge is fixed nice and cold

Removed the old fan--three small nuts and snap off connection. Ordered part and received the next day. Your company is great!!

The site offers a video for this part which worked perfectly. In addition to replacing the part, since the cardboard panel was off, we also cleaned all the dust off of the coils which someone recommended to do annually.

Replaced both the thermostat and defrost timer and still froze up and still warm air to the fridge, turned out to be the defrost heater coil. It was cracked in the middle, very easy to test with a multimeter. Replaced the heater coil and all is like new!

Took the ice storage bin out. Took the unit apart,and disamble the augar unit. Ordered parts from manufacture, which arrived in two days. As soon as I got the parts, I reassambled it. Work perfect. Good job!

I had removed the housing that the drum was in and taken the screws out to get to the broken drum. I removed it there was a set of 6 blades that crushed the ice that had to go back on the same order when I removed these I put them on a piece of wire in the order they came off (so I would get them back I the correct order). Then I reversed ... Read more the order and reassembled it in the opposite direction . It was fairly easy to do. I'm a 68 year old disabled woman so if I could do it I'm sure you could to. Good luck. It cost me $14.00 if I had bought the whole assembly it would have been $150.00. So it was well worth my time and effort.

Both water valves on this model have small rubber seals in them. When the seals wear, they stick and do not open, preventing water flow. To replace;
- unplug
- remove back bottom cover
- unplug valve
- remove valve
- detach water inlet and outlet (put a towel under first)
- install new valve in opposite ord ... Read more er

Removed evaporator cover, unplug 2 wires to thermostat, unclipped it from the coil. Installed new themostat back the same way.

Pulled out the ref.from the wall,turned off the water,removed the dual water valve,replaced it with the new one ,turned the water back on,every thing worked greatl,be sure to un plug the appliance while making repairs.

I turned the refrigerator off and took the screws from the inside back panel of the freezer. Then I took two mounting screws from the evaporator letting it pull out at the bottom a few inches. Then I removed the Defrost Heater and installed the new one. Then I put the mounting screws back in and replaced the Thermostat. Then I put the bac ... Read more k panel back on and turned the refrigerator back on. It has been working for now.

I basically followed the instructions offered when i searched for the ice maker. It was relatively easy to do, I undid the 2 screws holding the ice maker to the side of the freezer, the was the tricky part, holding a mirror so i could see the slots of the screws. loosened them, disconnected the electrical connection and reversed the proce ... Read more ss for the install. It took about 25 minutes and i was back making ice.