1985818101 Kenmore Freezer - Instructions

pulled the front panel first, then lifted the top(2bolts in each).
Then unhooked water and unbolted the water inlet valve from the back left corner behind the tub.four wires are connected Pay attenion to where they go, for easy reinstallation.NOTE: watch the clips in the front of the washer they flew off and it took half an hour on t ... Read more he internet finding out how they went back on.

Unplug washing machine.
Disconnect water supply hoses.
Remove valve service panel, 1 screw.
Remove valve from panel with wires attached. 2 screws.
Remove water outlet hose from old valve.
Mount new valve to panel. 2 screws.
Attach water outlet to valve.
Move wires from old valve to new valve.
Dre ... Read more ss wires.
Reinstall valve service panel, 1 screw.
Install new wire braded supply hoses.
Done. Hope to get another 20 years of service.

First let me commend PartSelect for their incredibly fast shipping. Ordered on a Thursday and it arrived on Friday!!

The repair itself was fast and easy and let me add I had never worked on a washing machine before.

1)Unplugged power cord from the wall.
2)Turned off hot and cold water at the shutoff valves.
... Read more >3)Disconnected water lines leading to the washer.
4)Removed 3 screws holding the bracket assembly on the washer.
5)Removed bracket and pulled water inlet valve out a few inches.
6)Held new inlet valve in same orientation as the old one and then one by one removed the four electrical wires from the old solenoids and attached them to the corresponding place on the new inlet valve.
7)Put inlet valve back in place, attached bracket, and secured it with the 3 screws.
8)Attached water lines to inlet valve and plugged power cord back in.
9)Turned water back on at shutoff valve and checked for leaks.

I washed a load of clothes after the repair and am happy to report that the hot water now runs in as fast as it did when the machine was new. This washer may be 30 years old but I think the old gal's got some life left in her yet.

Removed old part, installed new part. tested machine. worked fine.

unplugged electricity from socket, turned water feed off at spigots, put plastic basin to catch water under place where hoses connect to washer, used pliers to turn disconnect hoses from washer and let them drain into basin. unfastened top screw on panel (only one) and tipped the old water inlet valve connections out over basin -- still ... Read more spilled water onto floor, though. unfastened two screws holding old valve assembly to panel, set panel aside. loosened clamp screw on hose, moved hose off old valve -- a little water spilled out. held new assembly in similar position as moved wires one by one. used dry cloth to make sure electrical connections dry, then put hose back on, tightened clamp screw, fastened assembly to panel, fastened panel to washer, fastened hoses to valve, waited a half hour hoping any water on wires had dried, turned on water, washed clothes -- success!

Made sure I had the right part. Inlet Valve looked just like the one on the website. Unpluged washer. Removed screws and water hoses. Disconnected wires from old Inlet valve and reconnected to new Valve. Disconnected water line from Inlet valve to washer tub. Reconnected water lines. Ran a test cycle. Works great. Wife very happy. Therefo ... Read more re, so am I.

I removed the front of the washer then lifted the top up and swiveled it to the right. The solenoid is located in the back left. I remove the solenoid retaining screws from the the back of the washer, pulled the wires form the connectors on the top and bottom solenoids (hot and cold) and removed the defective valve. The new unit fit exact ... Read more ly! the total time to replace the solenoid valve was 25 minutes.

Removed door panel to get to the electric control conponents and noticed a burned wire to one of the door microswitches. Ordered the door switch repair kit from PartSelect. Also, ordered and replaced the thermal fuse at the same time since it was only $12 and didn't know if that blew at the same time the switch cooked. I had the parts com ... Read more ing standard delivery (3-5 days), but they arrived the very next day. Parts included easy to follow directions.Job went pretty smooth and the dishwasher works again Good experience!

Removed the front of the washing machine. Located & removed the water inlet valve from it's mounting on the back
inside face of machine. Replaced water valve, & restarted machine. Like new again!

Can't say enough about the speed of parts delivery & professionalism and accuracy recieved from the team at Parts ... Read more Select. Thanx again,

Greg W.

Shut off water supply, unplugged washer power, removed supply hoses from old washer valve assembly, removed valve mounting plate and removed old valve assembly from mounting plate, diagrammed and disconnected hot and cold solenoid valve wiring and removed valve assembly outlet hose. Installed and connected new valve, performing the prece ... Read more ding steps in reverse order. pressurized new valve, verified valve function and checked for leaks and placed washer back in service.

Took out 2 5/16" screws and loosened top and took off two ground wires and 2 hot wires for cold & hot water solenoids and removed & replaced solenoid wires and fill hose. Also Had fantastic delivery of parts.

Diagnosed the problem and ordered the part online in about 15 minutes. Part arrived about 3 days later. I followed the directions that came with the part and VOILA! washing amchine fixed. I unplugged the washing machine. I unscrewed the the screws at the back of the machine. Pulled out the faulty part and disconnected the electrical w ... Read more ires. Connected the electrical wires to the new part, and screwed it back in. In less than 30 minutes, I was done.

First, I opened up the back of the machine to see the way the water got into the tub. I turned off the water at the pipes, unplugged the machine, and disconnected the hoses from back. There were no leaks with the hoses, so I looked at the part that managed the water flow when operating and went on line to find the part.
I found it ... Read more and then ordered it from partselect.com. I got it two days later. I looked at how the other part was connected to the hoses and reused a clamp. I recommend getting a new hose clamp to make fitting it faster. I felt great after I got it to work, so that we didn't have to buy a new washer (the part was only $26). I think that Repair should be added to Reduce, Reuse, and Recycle.

open top of washer
remove two screws that hold water inlet valve
disconnect four wires and hose;replace new water inlet valve and reversed operation
everything went well

Washer is enclosed in a walled partition. I spent more time moving the washer out so I could get to the back of the machine. Due to Maytag's design of a removal sheet metal panel holding the valve the entire water valve replacement was performed outside of the machine. The replacement valve was an exact duplicate and made it a simple ... Read more swap out. More time was spent removing inlet hoses and outlet hose then in actual valve replacement.