Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
freezer quit working
1 personfound this instruction helpful.
Anthony from CIRCLEVILLE, OH
Really Easy
Less than 15 mins
Pliers
replaced relay switch when I finally got started to do the repair it took 15 minutes my biggest delay was no instructions were sent with the part and it took time to get some
Was this helpful?
Thank you for voting!
Defrost timer was not working
2 of 4 peoplefound this instruction helpful.
Harold from Grants, NM
Really Easy
Less than 15 mins
Screw drivers
Found the part on this site ordered and received part in 3 days. Took approx. 10 min to replace. Thanks for the quick service.
Was this helpful?
Thank you for voting!
Broken Water Nozzle at Door
1 personfound this instruction helpful.
Chris from Brentwood, TN
Easy
15 - 30 mins
Pliers, Screw drivers
(1) Ordered PS371704 from PartSelect! Best advice EVER! (2) Unplugged refrigerator (since the water solenoid on the back of the refrigerator is powered to switch ON the water, you NEVER have to turn off the water!) (3) Pull off the refrigerator's bottom grill. (4) With a small saucer under the fittings, unscrew the black and white tube fi
... Read moretting. There is only one nut to remove on the white tubing side. You'll need to undo the compression fitting on the black tubing and slide off the compression nut. You'll need to MAKE SURE you keep these nuts and replace onto the black and white tubing the SAME WAY you took them off. You'll NOT need to use nut drivers as finger tight is the key. Too hard and you'll ruin these plastic nuts. You should get only about 1/8 cup or less of water during this whole exercise. (5) Cut off the old, broken water nozzle. (4) Find a screw of the appropriate size to fit tightly 1/2 way inside the new tubing (this is to ensure your old and new tubing are connected to feed through the door). If screw is not tight within the tubing, wrap part of a plastic (thin) sack around this screw a couple of times and force into the tubing. You'll, of course, then need to use the hacksaw to cut the head off the screw as you'll be forcing the other half of the screw into the old cut tubing (6) Chase the dog out of the kitchen and cajole your wife (significant other) to push the newly joined tubes through the top of the dispenser, through the door and out the bottom as you will be gently PULLING on this old tubing from the bottom until the new tubing pops through the doors bottom. (7) Once this new tubing is out, you will separate the old tubing and, using the nuts in the proper sequence, connect this new tubing to the white tubing. (8) Plug the refrigerator back in and test flow the water. Check to ensure the plastic nuts have no leakage ... button up the bottom grill ... and enjoy the fresh water! PS> Don't forget to praise the wife (significant other) and give the dog a treat for staying out of your face!!
Read less
Was this helpful?
Thank you for voting!
Temperature in both freezer and fridge sections to warm!
2 of 4 peoplefound this instruction helpful.
Thomas from Spokane, WA
Easy
30 - 60 mins
Nutdriver, Screw drivers
Dear Part-select, I had a fridge that was not working food was melting in the freezer, Beer was warm. You get the picture anyway using your site I found the parts needed to to fix the issue in fact I ordered two parts one fixed the issue 50% and the other like 30% of the time! both parts with overnight shipping were cheaper than 1 pa
... Read morert if purchased at our local appliance part outlet:) not to mention the cost of a repair person. Thanks again! . Keep up the good work
Ordered a new defroster timer and replace old one. It works just fine. A $35 repair vs a $500 new appliance. Cool. GWE
Was this helpful?
Thank you for voting!
Refer iced up and would not keep the bottom cool. It was 70 Farenheit inside.
2 of 5 peoplefound this instruction helpful.
Larry from Newton, KS
Really Easy
15 - 30 mins
Screw drivers, Socket set
I simply removed 4 screws holding the casing and then 2 more holding the timer. It was very easy. I then replaced the timer by unplugging and plugged the new one in. I replaced all the screws and the job was done. Less than 30 minutes. I was very impressed with the shipping time. When I ordered the part, I had it the next day.
Was this helpful?
Thank you for voting!
Refrigerator keeps frosting up and not cooling
1 of 2 peoplefound this instruction helpful.
Marvin from Pima, AZ
Really Easy
15 - 30 mins
Nutdriver
Refrigerator started frosting up and running all the time.I'd defrost it and it would frost up again in about a week.The timer seems to be work so I just guest it mite be the Defrost Thermostat.I removed the duck in the center and back panel in the freezer compartment defrosted it and switched Thermostats and replaced panel and duck, goi
... Read moreng to lower compartment of the refrigerator.So far it seems to be working a little more time while tell.
Read less
Was this helpful?
Thank you for voting!
No freezing or cold in either freezer or refridgerator - compressor did not run.
1 of 2 peoplefound this instruction helpful.
George from Sunnyvale, CA
Really Easy
15 - 30 mins
Nutdriver, Screw drivers
Traced issue to defrost timer ( burned compressor & element contacts). This unit is mounted next to the temperature adjustment control in the refridgerator area - right in front. Removal of plastic cover provided easy access to the timer. Unit unscrews from the mounting then unplugs. Installation is reverse of removal.
Was this helpful?
Thank you for voting!
light bilb went out
2 of 6 peoplefound this instruction helpful.
Denise from Landover, MD
Really Easy
Less than 15 mins
replaced it
Was this helpful?
Thank you for voting!
frezzer iceing over and not cooling the refrigerator
1 of 4 peoplefound this instruction helpful.
Marcus from Pine Hill, AL
Really Easy
Less than 15 mins
Just removed the two screws and unpluged it. Then I pluged the new one in and replaced the screws. It runs like a brand new reffrigerator. Thanks for the fast delevery. Will do busness with you in the future.
Was this helpful?
Thank you for voting!
Freezer built ice, fridge not cold enough and running constantly.
1 of 4 peoplefound this instruction helpful.
LUIS from CENTENNIAL, CO
Really Easy
Less than 15 mins
Screw drivers
Removed front low grill, removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the wires. Reversed process to install new timer.
Was this helpful?
Thank you for voting!
freezer worked frig was warm. Ice maker is still not working
0 of 1 peoplefound this instruction helpful.
steve from Kirkland, WA
Really Easy
15 - 30 mins
Screw drivers
Removed two screws to get to defrost time pull panel down remove two screws holding time and reinstall
Was this helpful?
Thank you for voting!
Freezer okay, but fridge was warm
0 of 1 peoplefound this instruction helpful.
brad from minneapolis, MN
Easy
30 - 60 mins
Nutdriver, Screw drivers
Website was great!
The defrost timer was right in front. 2 minutes and a screwdriver and I had it replaced.
To replace the thermostat, I had to take out the back panel, defrost it and then install the new part. the only problem was that the heatshrink tubing they sent was too large. Otherwise, it worked great.
My Orders
