1938 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Kickplate clip broke off
2 of 4 people
found this instruction helpful.
-
Paul from Fort Wayne, IN
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
Reattaching the kickplate clip was easy, but the tab that holds in place was broken. It would slide back when the kickplate was installed. I fashioned a replacement tab out of a piece of 3/32 aluminum bent into a U with the hammer. To hold it in place I drilled and tapped one hole and used a 6-32 machine screw.
Was this helpful?
Thank you for voting!
Condenser fan motor froze up
2 of 4 people
found this instruction helpful.
-
Douglas from Mesa, AZ
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers
Unplug fridge, unpluged fan motor from plug socket, removed bracket screws, removed fan retainer clip from shaft. removed screws holding fan to bracket
Was this helpful?
Thank you for voting!
Ice maker wasn't getting water
1 person
found this instruction helpful.
-
Jimmy from LIBERTY, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Wrench set
Removed old water valve on bottom right back side of fridge installed new one which actually took less work
Was this helpful?
Thank you for voting!
The old ice maker water valve washer in the water inlet port went bad and was leaking. Lasted for 35 years,
1 person
found this instruction helpful.
-
Edwin from Mount Washington, KY
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
The Whirlpool water inlet valve was better design than the original. All I had to do was drill 2 holes to mount it since it didn't mount in the same location as the old one. I liked the push in connection for the water outlet to the ice maker better than the original plastic screw connection.
Was this helpful?
Thank you for voting!
Condenser fan making noise
2 of 4 people
found this instruction helpful.
-
Richard from North Easton, MA
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Wrench set
I removed 7 screws hold the heavy cardboard cover on the rear of the fridge. The dificult part was taking the screws that hold the 3 fan motor braces on the fan out. After that it was a matter of making the wire conections and putting it back in. I did not have enough room to laydown to do the work, If i had it would have been a lot easi
... Read more
er to see the screws that had to be removed. All in all an easy job, and the part was a perfect fit.
Read less
Was this helpful?
Thank you for voting!
Ice maker was not working.
1 person
found this instruction helpful.
-
GREGG from WEST CHESTER, PA
- Really Easy
- 30 - 60 mins
-
Nutdriver
Ordered new single outlet water valve, received in less than two days. Removed old one, and the repair pretty much feel in place. Instructions were there as a backup. ........ Just curious if the connection from the water source to the valve outlet connection could b a quick connect just the like the water line going directly to the ice
... Read more
maker. Gregg in PA.
Read less
Was this helpful?
Thank you for voting!
THE LOWER RACK WAS CORRODING IN SPOTS AND WAS RUSTING
1 person
found this instruction helpful.
-
JOHN from JUPITER, FL
- Easy
- 30 - 60 mins
THERE WERE NO INSTRUCTIONS INCLUDED, COULDN'T FIGURE 0UT HOW TO INSTALL THE NEW ROLLERS ON THE NEW RACK FINALLY INSTALLED THE OLD ROLLERS ON THE NEW RACK AND THEY WERE MUCH EASIER TO INSTALL I DONT UNDERSTAND
WHY THE NEW ROLLERS WERE THE SAME AS THE OLD ROLLERS
EXCEPT FOR THE COST.
WHY THE NEW ROLLERS WERE THE SAME AS THE OLD ROLLERS
EXCEPT FOR THE COST.
Was this helpful?
Thank you for voting!
Bottom tray wheels would catch on old door gasket making it difficult to remove and insert.
2 of 4 people
found this instruction helpful.
-
charles from sacramento, CA
- Really Easy
- 30 - 60 mins
-
Socket set
Followed the exellent instructions, the flange kit really solves the problem of lower rack wheel catching on the seal. Superior replacement parts compared to previouse repair two years ago.
Was this helpful?
Thank you for voting!
water leaks. ordered the door gasket
1 person
found this instruction helpful.
-
William from VALPARAISO, FL
- A Bit Difficult
- More than 2 hours
-
Screw drivers, Socket set
when removing all the screws from the door gasket the dishwasher door and frame separates making reassembly not possible. you have to leave at least one screw on bottom half on each side, After all that the door would not close. I had to remove the new gasket and put the old one back on.
I need to return the gasket for credit
I need to return the gasket for credit
Was this helpful?
Thank you for voting!
original motor stopped
2 of 4 people
found this instruction helpful.
-
Paul from Lowell, MI
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Socket set
removed old and instaslled new. biggest problem was getting to one of the screws.
Was this helpful?
Thank you for voting!
Lack of assembly instructions
1 person
found this instruction helpful.
-
Ray from Lufkin, TX
- Easy
- 1- 2 hours
-
Screw drivers
YouTube was very helpful
New racks works better that way expected. Rearrange ment maximized loading
New racks works better that way expected. Rearrange ment maximized loading
Other Parts Used:
Was this helpful?
Thank you for voting!
my old lower dishwasher rack was rusted out and some parts broken.
1 person
found this instruction helpful.
-
Kathy from ELGIN, IL
- Really Easy
- 30 - 60 mins
-
Pliers
Snapped on the rollers, removed the center part from the old rack that sprays the water and snapped it on the new one. We then bent the back row down so it would acomodate my larger items. My old rack had that feature. You could either have the rack up or down. Now l
ooks beautiful and works perfectly.
Could have used some di ... Read more rections though.
ooks beautiful and works perfectly.
Could have used some di ... Read more rections though.
Read less
Was this helpful?
Thank you for voting!
soap dish door does not always pop open
7 of 20 people
found this instruction helpful.
-
John from Dubuque, IA
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers
the plastic pin that retains the spring has a head on one end that hits a plastic stop on the door to keep it from coming out. I used a small grinder and made a flat spot on the head diameter to make it easy to slide out. This is easier than trying to pry the door off the pin at the two retaing snaps. I was conderned these pin retainer
... Read more
clips were brittle and would break off.
Once the pin is slid out, it is a matter to hold the new spring holes in line with the pin. rotate pin so flat side you ground is turned up, so pin will not move out that way. Tiij about an hour
Once the pin is slid out, it is a matter to hold the new spring holes in line with the pin. rotate pin so flat side you ground is turned up, so pin will not move out that way. Tiij about an hour
Read less
Was this helpful?
Thank you for voting!
fan motor had gone bad
1 of 2 people
found this instruction helpful.
-
william from whitwell, TN
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set, Wrench set
I removed the nuts that held the motor mount, then removed fan blade, cut the wires, and slid the motor pass the mounts and the coil shroud, Installed motor in reverse order. worked out ok.
Was this helpful?
Thank you for voting!
freezer and food section too warm
1 of 2 people
found this instruction helpful.
-
William from Milford, MA
- Easy
- 30 - 60 mins
-
Socket set
removed lower back cover. diconnected fan ass'y electrical connection, removed fan housing (3 screws). removed fan motor from housing. cut old connector from fan and installed on new fan with wire nuts included. re-installed new fan to housing and re-installed housing to frame.
Was this helpful?
Thank you for voting!