1544 - Instructions

1. remove 2 screws holding element in place
2. unscrew the wires from the old element
3. the connectors on the new element was different from the old one
4. cut old connectors from wires
5. prepare wires for new connectors
6. install new connectors
7. connect the new element to the wires
8. replace the 2 ... Read more screws removed in step 1
9. test the repair
10 it worked great.

First, I removed the 2 screws holding the element in place. Next, I pulled the element out abotu 4 inches and disconnected the wires attached to the element. I was able to do one by hand, but the other required needle nosed pliers. (be careful not to pinch the connecting wire). Then I attached the wires to the new element. Lastly, I ... Read more replaced the 2 screws to hold the new element in place.

Inspect new part; collect tools; TURN OFF BREAKER; remove two screws holding defective element (KEEP!); install new element using saved screws; turn power back on; test; celebrate!

removed old burner. 2 screws. disconnected connectors and reconnected new burner screwed back in place. turned on stove worked first time. perfect fit. 15 minutes total repair time. item arrived promptly and at half the price of the Whirlpool website.

very easy remove the bad bulb install the new one

First I turned off the circuit breaker...just to be safe. I removed the two screws that hold the element in place. I was surprised you didn't went new screws, but that was OK. I pulled out the old one, and pulled out the two wires. It was tricky, for me, to pull apart the old wires. Luckily, a friend was braver than I, and just pulle ... Read more d them apart using a little muscle, and easily connected the new wires. I screwed it back in, and it was done! I was really impressed with how quickly it arrived at my door, too.

To replace the light bulb, I removed the screw and the cover, unscrewed the old bulb, replaced with the new bulb and replaced the cover, securing it with the small screw. It worked appropriately with normal use for a few days and then I noticed the light was not coming on when I opened the door.

I removed the cover and pulled ... Read more out the bulb to find that the filaments inside are dangling and burned through. I need them replaced, please.

Took two screws out of burned out unit. Pulled element forward and pulled off connectors. Replaced new element on connectors and screwed back in. Extremely simple. Less than 10 minutes.

Removed oven door (made sure hinges were locked open and stayed open). Remove part on top of trim, removed rusted trim and replaced with new trim. Replaced part on top of trim and screwed all back together. Put oven door back on and unlocked hinges. It was easier than the trial run (when I hadn't realized that the hinges weren't locked op ... Read more en!)

Your support team helped tremendously in ordering the parts. Parts arrived in only 2 days. Upon taking the door off the oven we had to remove several screws, then more screws. Was able to take it almost fully apart, replace old broken parts with new. Putting it back together was like a puzzle. We did it though and saved money! Thanks

Unscrewed eight screws. Removed rusted part. Cleaned area with Windex. Replaced new part.

Very simple. Lift oven door off brackets and set on floor. Remove sheet metal screws holding on existing trim piece, Clean area beneath trim.
Put new trim piece on, don't tighten any of the screws until all have been started as some adjustment is needed to align the holes for the screws.

remove screws, re-install screws

It was pretty simple. Just remove the door as the bottom piece holds all the parts together. Place on table top and remove old trim. Install new trim and install door. The only difficult part was the trim had a space for the glass door front. I opened up the space so that the glass would seat easier. Went together real easy. Stove ... Read more looks like it's brand new.

Repair went a lot faster and easier than I anticipated. Instructions are similar to those posted by others.
1. Verify that new gasket looks mostly like old gasket as best you can since not all of old gasket is visible.
2. Shut off circuit to oven (optional, but good practice)
3. Remove racks, trays, etc from oven to red ... Read more uce weight at Step 7
4. Remove oven door by partially opening door to broiler position (about 20 degrees). Door should catch and stay open on its own. Slide up and lift off door. The “hinges” are spring loaded so carefully return them to closed position so they won’t snap shut on fingers.
5. Remove Phillips screws, one on each side wall of oven liner.
6. Remove two hex screws and metal gasket-holder on top center of oven liner.
7. Pull and slide oven liner out of oven mainframe about 1/4 “ to 3/8”. This may be the most difficult part of the job.
8. If possible to remove just a couple of inches of one bottom of old gasket (right side is easiest), verify that the cross-section profile of both old and new gaskets are essentially the same. If not, you have the wrong gasket.
9. Pull and remove old gasket. If gasket is dry and cracking, it may be necessary to scrape it out with putty knife, flat-blade screwdriver, etc. if it has fused to metal over the years. Note how it was installed on the metal edge of the oven liner.
10. Locate the mid-point on the new gasket length and begin inserting it at the top-center of the oven liner where you removed the two hex screws. Continue installing along both left and right sides of the liner. Each end of the gasket should extend to just above the respective hinge. No trimming should be necessary. Ensure a snug fit all along each side and top.
11. Push liner back into oven mainframe. Replace Phillips screws, gasket-holder, and hex screws.
11. Pull out each hinge to broiler position.
12. Replace door by sliding down onto hinges. Close door and check for tight fit against gaskets. Gaskets will flatten somewhat over time
13. Restore power, racks, trays, etc.