14384 - Instructions

All Instructions for the 14384
106 - 120 of 377

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washer would not spin out on rinse cycle
1 person found this instruction helpful.
  • Duane from COTTAGE GROVE, MN
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
used the u-tube video and it worked just as the video described it!!
Was this helpful?
Thank you for voting!
The machine stopped agitating and spinning
1 person found this instruction helpful.
  • David from COLORADO SPGS, CO
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
The shredded rubber under the machine pointed to a drive coupling failure. Unscrew the control panel and type it back. Undo the body clips on either side and tip forward and remove the body..... At least on this model. Lay the machine on it's back and remove two motor clips. Uncouple one hose so that the motor can be removed. This exposes the broken drive coupling. Remove it's remains from the motor shaft and the transmission shaft. Install the new one and reverse the steps. NO BIG DEAL. Up and running in less than one hour. Total fix cost $18.....I'll take that any day.
Was this helpful?
Thank you for voting!
Would not spin
1 person found this instruction helpful.
  • Ricky from Cullman, AL
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
This was not the problem, but the replacement was really simple. The video provided made it a breeze
Was this helpful?
Thank you for voting!
Canister not spinning
1 person found this instruction helpful.
  • Edwin from Mount Vernon, NY
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
Followed the instruction from the video. I am very satisfied with the accuracy of the instructions.
Was this helpful?
Thank you for voting!
Washer will not spin
1 person found this instruction helpful.
  • Bill from EASTLAKE, OH
  • Very Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
I followed the online video. It worked perfectly.
Was this helpful?
Thank you for voting!
Washer filled but did not agitate or spin and was making a loud clicking sound.
1 person found this instruction helpful.
  • Stacy from PRINCETON, NJ
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
I found a YouTube video that was for the drive motor coupling that had the sound the machine was making. Then after ordering the part, I followed the video here. I was able to do the repair without unhooking the water by tilting the washer. Only thing I would like to add is that it took me two tries because the part is newly improved and tighter so I hadn't pushed it on enough. Smelled burning and banging, so I found another video explaining how to use a socket and hammer to gently tap the coupling onto the motor until it is flush with the inside. Put it back together and wallah. Good to go. Done by a 49 year old woman for under $20.
Was this helpful?
Thank you for voting!
Washer wouldn't agitate or spin
1 person found this instruction helpful.
  • Dawnie from Colorado Springs, CO
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
After taking out the agitator to see if the problem was there, we tipped the washer over and started diassembling the major pieces. It was easy to find the broken coupling between the motor and the transmission drive and fairly easy to get it out. The part was here in three days and is a better design than the original one because it has a metal sheathing inside the place where the old part broke. We had the washer up and running in about 30 minutes.
Was this helpful?
Thank you for voting!
Tub Would Not Spin
1 person found this instruction helpful.
  • ERIC from SAN JOSE, CA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Socket set
Unplugged all electrical connectors, removed gear case & motor as one, separated motor from gearcase, replaced coupler, reinstall, was alot easier than it looks, only thing now is it has a clicking noise when spinning, works fine, will wait for something to break and find out what clicking noise is.
Was this helpful?
Thank you for voting!
Agitator would not spin.
1 person found this instruction helpful.
  • Brandon from McHenry, IL
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set, Wrench set
Rested washer against wall so I had access to the motor/gearbox on the bottom. Unclipped motor and starter assembly - removed old coupling and spider, installed new ones and reassembled. The hardest time I had was getting the clips off - I have big hands and little patience. All in all, rather simple, but can be time consuming for wha t it is.
Was this helpful?
Thank you for voting!
Washer stopped spin dry or agitation.
1 person found this instruction helpful.
  • Paul from Draper, UT
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
Watched Youtube video, was similar except screws for topside control panel were in rear. Disasemble was simple and fast. Reassemble was a little tricky as I could only get one clip back on the motor and then the other was not reaching. I had my daughter tilt the washer back so the motor wasn't hanging down and it went together. Washer now runs like new, nice to know that I only had to pay for the part and saved myself $100 bucks! Thanks!
Was this helpful?
Thank you for voting!
Washing machine would not agitate
1 person found this instruction helpful.
  • Chris from North Wildwood, NJ
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set, Wrench set
I first tipped the machine on its side, so that the motor and gearbox would be exposed. I disconnected the hoses from the water mump, and removed it. I then removed the motor by unsnapping the retainer clips. the damaged coupling came off very easily. I just pried it off with a screw driver. I installed the new coupling, and put e verything back in reverse order. The machine works great now.
Was this helpful?
Thank you for voting!
Broken motor coupling
1 person found this instruction helpful.
  • Roger from New City, NY
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Just remove the covers, remove the electric drive motor. Replace the failed coupling with the improved design parts. Reinstall motor and covers. Tested OK. The new part will outlast the rest of the machine!
Was this helpful?
Thank you for voting!
Washer wouldn't spin or agitate
1 person found this instruction helpful.
  • Alfreda from Hempstead, NY
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
1st I took the brackets then water pump off. Then I unscrewed the brackets and took off the motor. Under the motor the coupling just slide off.
Was this helpful?
Thank you for voting!
Washer would not agitate or spin
1 person found this instruction helpful.
  • Scott from Indian Harbour Beach, FL
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
First I removed the center cover of the tub, then removed the bolt that was underneath it.
I then tipped the washer back far enough that it wouldn't fall forward.

Next I removed the two hoses connected to the motor/gearbox assembly.
I then removed three bolts that hold the gearbox/motor assembly to the bottom of the t ub and slid it down.
The next step is to separate the gearbox from the motor. To do this I removed the spring clips that hold the water pump to the motor, and then the spring clips that hold the gearbox to the motor.
The broken coupling between motor and the gearbox was then removed and replaced with the new one.
Next, put every thing back together.
Was this helpful?
Thank you for voting!
washer quit wash & spin functions motor runs
1 person found this instruction helpful.
  • william from newport, VT
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
completely remove and disconnect pull out remove hoses from back drain hose move to where i had room to lay down on back (after i drained the full machine out) removed water pump and motor clips removed both uncliped wire harness from motor so i could sand off shafts etc replaced coupler with the new one which has a metal inse rt replaced parts and reinstalled. aligning coupler to motor and gear case takes a little extra work and luck put back in sevice
Was this helpful?
Thank you for voting!
All Instructions for the 14384
106 - 120 of 377