1259 - Instructions

No problem installing oven sensor, but I diagnose the problem wrong, I need to change(ERC-11)control p/n wb27k5140

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appl ... Read more iance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

Shut down breaker; remove stove back cover plate (8 screws); remove the control knob; remove knob screws (2); simply remove one wire at a time and replace the coresponding wire to the new control unit; remove the snap ring on the knob bar and snap off to fit the proper length; place the control unit in position and reinstall the 2 screws; ... Read more reinstall the back panel; position stove and turn throw the stove breaker on; test the burner control.

First I Pulled the oven away from the wall and turned off the gas and unplugged the oven. I then removed the bottom drawer and the oven door to get easy access to the ignitor location. I then removed the oven racks and the 2 shields which cover the ignitor with a screw driver. I then removed & unplugged the ignitor and 2 screws holding ... Read more the ignitor in place. This all took about 15 minutes. I then reversed the process and installed and assembled the oven. It only took about 25 min in total time and low and behold the oven worked again. Amazing the technology stuff. My wife things I am a genius...again. Not!!!

Ordered a new switch and replaced the old one with it.

I removed the oven door by unlocking the hinges and pulling out. Set on workbench (with towel/pad) and removed handle, four screws, then bottom and inside panel screws, then one nut to finally be able to get at the inner glass insert. Removed insulation and then took an extra hour to really clean all surfaces (middle glass was quite gre ... Read more asy due to inner glass being broken for a while. Reassembly wasn't bad, but took a while to figure out that the two thin 2" red spacers belonged around the two handle screws. This was tough to figure out as they come off when taking the handle off, but you can't see them, so didn't know where they came from! Anyway, if you're just a bit handy, you can do this job.

As a former appliance repairman, the installation went just like the repair instruction video.
Just use care not to scratch anything and clean behind the appliance and cabinet walls, etc. It's worth a hug and a piece of pie!

Unpluged range for safety (power earlier removed by circuit breaker turnoff).
Removed two screws from front switch cover.
Removed knob from effected switch and removed the wires on the back of the switch.
Removed two screws holding switch and removed switch.
Reversed the process to install new switch.
The entire ... Read more project took about ten minutes.

I just removed the range elements and old bowls, placed the new bowls into the range top, and inserted the heating elements. What surprised me was the quickness in filling the order. I had the new parts the next day! Great!

1. Pull range out from wall
2. Unplug range
3. Remove back cover using drill and screwdriver bit
4. Remove dial handle on affected burner dial
5. Remove two screws to unattach broken infinite switch
6. Disconnect wires from broken infinite switch
7. Reconnect wires to new infinite switch
8. Attach new in ... Read more finite switch using two screws
9. Use pliers to snap off end of post to fit your burner dial, if necessary. It was on ours.
10. Reconnnect dial handle.
11. Reattach back cover using drill and screwdriver bit.
12. Plug range back in
13. Relocate stove against wall

I unplugged the burner, lifted the old drip pan out, put new drip pan in, plugged burner in. The stove looks brand new and it took less than 2 minutes.

Removed oven door (made sure hinges were locked open and stayed open). Remove part on top of trim, removed rusted trim and replaced with new trim. Replaced part on top of trim and screwed all back together. Put oven door back on and unlocked hinges. It was easier than the trial run (when I hadn't realized that the hinges weren't locked op ... Read more en!)

turner off circuit breakers for range, i rolled the range out from between counter tops so i could see the burner sw. using a flash light read all the numbers on the switch to my wife who wrote then down, knowing what the switch looked like i could find could find correct instruction video on parts select & check the switch numbers & or ... Read more dered it. replacing- made myself a drawing of the wiring connections, replacing switch-power off, unscrewed mounting bracket, removed switch, removed ONE WIRE AT A TIME & CONNECTED IT TO SAME TERMINAL ON THE NEW SWITCH, remounted the switch & turner on circuit breakers

I pretty much followed the youtube video posted under the part that I needed. Turned off electricity to that area of the house. Unplugged stove. Took out the old sensor, pushed new sensor cord through the back hole. I did put a small amount of tape,so I could pull it through from the back better. It was impossible to get the clip discon ... Read more nected in the back and the new clip didn't match up correctly anyway. Ended up having to cut the wires and strip them. I twisted them together and put on the ceramic wire nuts on. Reversed ever thing I did and F3 appeared. Looked that code up on internet. It was from an open or shorted oven. Suggested I check the connections. Pulled stove out again, unscrewed caps on wires and noticed the sensor's wire had another cloth type coating on it. I gentle cut that off, twisted and capped wires again. Plugged in oven, turn on electricity, and tried out stove. Everything is working just fine. Everything took a little longer because this was first time doing this type of repair.

I read some of question & answer to the problem I was having with the oven. When I saw do-it-yourself that all I need to know. Repair man quote me for 100.00 dollar he will do it plus part. So I save 100.00 dollar and done it myself. Thank to partselect for fast and quick delivery service. It was only 2 screws holding the element and th ... Read more e connector was a just plug it into the other plug very easy to do. I will always come back partselect for answer and help and buy the part from them. YOU ROCK PARTSELECT