119905 Kenmore - Instructions

All Instructions for the 119905
76 - 90 of 155

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Three of four electric coils won't turn on
1 of 2 people found this instruction helpful.
  • Arsenio from Beaverton, OR
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
I took out the coils manually by pulling them out with slight pressure. Then I lift the hood by first unscrewing the four screws. I have never done anything like this before just intuitive sense to locate the screws that needed to be loosened. Afterwards I remember placing something underneath like a piece of 2x4 wood block to act as supp ort to hold the hood open so I can work on the coils. The parts I got are exactly the same as those I am replacing so I just copied the connection and voila my electric range is working like new. Well of course before I touched anything, I made sure I turned off the main switch and that nobody switches it back on without my knowledge. Thanks for providing the parts, I just saved myself from buying a $600 electric range.
Was this helpful?
Thank you for voting!
The Problem Was That The Plug Was Gone It Fell Down Out Of The Bracket
1 of 2 people found this instruction helpful.
  • Elnora from Brundidge, AL
  • Easy
  • 15 - 30 mins
  • Screw drivers
I took the old wires and plug off and replaced it with the new block it works fine
Was this helpful?
Thank you for voting!
Broken hinge
2 of 5 people found this instruction helpful.
  • MICHAEL from MAY'S LANDING, NJ
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Replaced same very simple.
Was this helpful?
Thank you for voting!
Burner will not cool down. I have to switch all the way off.
1 of 2 people found this instruction helpful.
  • Bennie from Kite, GA
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
First unplug the electricity from the stove. Replacement terminals on back of switch are set different than the originals. So, I took notes (purple wire =P, Black wire=L1, two yellow wires = H1 & H2, and orange wire=L2). Your stove might be different in the color coding. Just take notes. First I unscrewed the screws on the top back plate of the stove. Removed the back plate. Took notes on where the wires went. Removed the wires going to the five terminals. Unscrewed the two screws on front panel of the stove holding the old switch in place. Removed the old switch. Put in the new switch through the back of stove. Determined the length of the control shaft. Take the switch back out. With two pliers on the control shaft, holding the pliers closer to the switch firmly, use the second pliers just past the predetermined breaking point. With the second pliers snap off the control shaft. Be careful not to snap off two much. Place the switch in the proper place and mount to the stove. You may need some parts in the assembly parts package for this. I did not. Inside of the parts package is a set of plastic parts. I selected the part I needed to insert into the control knob for a bushing just to take up space. I placed that part inside of the control knob. I then placed it onto the control shaft. Plug back the wire going to the electric outlet. Instead of unplugging and plugging, you might want to switch off the circuit breaker and switch back on when the job is done. It works!
Was this helpful?
Thank you for voting!
Sockets burnt out.
1 of 2 people found this instruction helpful.
  • James from Bear, DE
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Repair was very east. The suppliers package had all of the necessary parts ceramic wire nuts wire Ect. Excellent.
Will buy from Part Select Appliance again.
Was this helpful?
Thank you for voting!
Heating coils stop heating
1 of 2 people found this instruction helpful.
  • Sharon from TEMPLE, GA
  • Very Easy
  • 15 - 30 mins
  • Screw drivers
Remove heating coils raise stove top unsrew terminal blocks cut wires assemble terminals strip wires twist wires together install wire nuts apply heat shrink lower stove top plug in stove repair complete.Thanks.
Was this helpful?
Thank you for voting!
Pulled the heating element on each burner installed the drip pans.
1 of 2 people found this instruction helpful.
  • Sharon from AURORA, MO
  • Very Easy
  • Less than 15 mins
They fit perfectly for this stove. I had bought some drip pans but definitely not the correct pan. Saved time and about same at stores price. Great service thank you will order elements next. Pull heating elements remove drip pans and replace with new pans ,replace heating element. Done
Was this helpful?
Thank you for voting!
2 burner elements not heating
1 of 2 people found this instruction helpful.
  • Brian from MENASHA, WI
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Simple: Snip old terminal block off. Strip wires. Connect new Terminal block using twist-on wire caps (provided in kit). Mount to stove top with existing screw. TIP: Make sure you insert the wire lead into the terminal block the right way (not upside down). Otherwise burner element will not insert into terminal block properly.
Was this helpful?
Thank you for voting!
Stove Burner wouldn't heat up
1 of 2 people found this instruction helpful.
  • Donna from Sandwich, MA
  • Really Easy
  • Less than 15 mins
Someone did the repair for me.
Was this helpful?
Thank you for voting!
old drip bowls
1 of 2 people found this instruction helpful.
  • Vera from Snow Camp, NC
  • Very Easy
  • Less than 15 mins
replaced old drip bowls with new ones
Was this helpful?
Thank you for voting!
Pitted, Eroded Drip Pans
1 of 3 people found this instruction helpful.
  • Josephine from Malden, MA
  • Really Easy
  • Less than 15 mins
1. First I pulled out the heating element from stovetop and removed old pan (no screws) very simple. 2. Put new pan in and inserted the heating element back in place.
Was this helpful?
Thank you for voting!
No Power to the Oven
1 of 3 people found this instruction helpful.
  • Tony from Hartford, CT
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Watching the video showed an easy, unscrew and screw back on process while connecting the wires back. It was really that simple. Once it was complete (not even 10mins), plugged it back in, and its been working great since.
Was this helpful?
Thank you for voting!
light bilb went out
2 of 6 people found this instruction helpful.
  • Denise from Landover, MD
  • Really Easy
  • Less than 15 mins
replaced it
Was this helpful?
Thank you for voting!
Left rear burner had a damaged burner prong.
1 of 3 people found this instruction helpful.
  • Jackie from Charlotte, NC
  • Really Easy
  • Less than 15 mins
I just had to plug the new burner plate in the receptical
and it works again very well.
Was this helpful?
Thank you for voting!
This is for a basic four-burner electric stove:One element was bent so I replaced it and all of the drips bowls needed replacing.
1 of 3 people found this instruction helpful.
  • Olivia from FAIRLEE, VT
  • Really Easy
  • Less than 15 mins
The element pulls out easily and slides right back in and the drip bowls just lift in and out. TaDa !!
Was this helpful?
Thank you for voting!
All Instructions for the 119905
76 - 90 of 155