1199028 Kenmore - Instructions

All Instructions for the 1199028
91 - 103 of 103

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
burner would not heat up the connection was bad
  • Earl from Union Mills, NC
  • Really Easy
  • Less than 15 mins
  • Screw drivers
loosened the screw holding the block pulled it out toget to wire cut it about 4 inches long followed the inst.with block kit and it was a breeze. burner working fine now should have did it sooner.
Was this helpful?
Thank you for voting!
The surface burner socket that the burner plugs into melted.
  • Gary from Chesapeake, VA
  • Easy
  • Less than 15 mins
  • Screw drivers
Cut the old wires off, removed the screw holding the clamp, installed the new parts. Problems I encountered were the wire nuts. They were too small for the wire gage of the replacement part and the original oven. I had larger wire nuts in my workshop. Also, why so many extra parts like the shrink wrap tubing, two metal clamps to hold t he socket, etc.
Was this helpful?
Thank you for voting!
Burner keep coming on and going off had a short in burner plug-in block.
  • Judith from Staunton, IL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Turned off stove breaker. Unscrewed burner from stove top, took out burner and spill pan. Lifted top of stove, cut the wire as instructed and put all parts together as instructed. Placed everything back together as instructed. I did it myself!
Was this helpful?
Thank you for voting!
Replaced burner block
  • Glenn from Fossil, OR
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Looked at the instructions and cut the wires, put the new wires in the block, attached the block to the range, put the new wires to the range wires using the wire nuts. I plugged the element into the block turned on the power, tried the element and it worked. It was really a easy repair.
Was this helpful?
Thank you for voting!
Drip Bowl Replacement
  • Jennifer from Arena, WI
  • Really Easy
  • Less than 15 mins
I could not find the larger size universal drip bowl to fit the 8" burners on my stove. This product replacement is perfect.
Was this helpful?
Thank you for voting!
Surface burner block corroded
  • Teresa from Kasson, MN
  • Really Easy
  • Less than 15 mins
  • Screw drivers
It was a very easy fix. I followed the instructions that came with the kit and cut the original cable. Everything you need is in the kit; very few parts. Piece of cake and saved a lot of money an appliance repair person would have charged. This burner works better than the rest. I'm seriously considering replacing the other three blocks.
Was this helpful?
Thank you for voting!
Blocks were broken
  • James J from Sweet Grass, MT
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
The four kits arrived, use of a pliers and shink wrap and side cutters...strip wires, twist wires connect wire ties, shrink wrap...little fire, plug the elements...done...four in about ten minutes...Instructions in each package...no problem...very easy...saved twice the money or more...Thanks for the parts...recommend this site purchase.. .parts arrived very timely...J. Iriwn
Was this helpful?
Thank you for voting!
Surface Burner not working
  • Cody from Abilene, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I lifted the stove top and cut the two wire connected to the block. Attached the new wire connectors, new block and checked to make sure it was working. The part that took the longest was getting the screw out of the mounting brracked(it was corroded on). I sprayed some WD40 and waited 5 minuts, it came loose. Then i mounted the new b racket and installed the burner. double checked everything and lowered the top. Done
Was this helpful?
Thank you for voting!
electric surface unit not working
  • vincent from Martinsville, VA
  • Easy
  • 30 - 60 mins
  • Screw drivers
After turning off circuit breaker to the stove, I removed all surface units , removed the 4 screws holding the top and lifted up. The plug in was burned out (the wire was burned). Look at the old plug-in so as to be able to match the new one and insert the pre- crimped end of wires into the block and the block into the metal holder that matches your old one. (The kit comes with 2 different metal holders)After this, cut out the old wires and wire nut the new wires with the stove wires. Put shrink wrap protector on the wire nuts and heat to shrink it tight.attach the block to the stove top and wa la its done. Very easy.
Was this helpful?
Thank you for voting!
one burner that would not heat and others that would not out out much heat
  • Charles from Villa Ridge, MO
  • Easy
  • 30 - 60 mins
  • Screw drivers
I noticed that one of the burner blocks was completely burned and the others were corroded. I ordered blocks for all four burners. Installation was easy except for one block. The screw holding the bracket to the range top was completely corroded in place. I used a correct size easy-out, which is a left hand tap and drill, to remove th e screw. That took about five minutes, including tracking the easy-out down in one of my many toolboxes. The entire replacement of four blocks took about one and a half hours. Stove top cooks like new on all burners! The part kit had all the right parts and they fit like a glove!
Was this helpful?
Thank you for voting!
Oven door hinges broken on range
  • Ross from Bridge Hampton, NY
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
First off I want to thank Parts Select for getting the parts to me with-in 24 hours. This is incredible, I effected the repairs with-in 45 minutes thanks to the instructions I found on your site. As a result of Parts Selects web site I think I can handle any appliance repair going forward. Many thanks Ross,
Was this helpful?
Thank you for voting!
Electric Range Element's Not Heating
  • Robert from Waldorf, MD
  • Easy
  • 1- 2 hours
  • Screw drivers
Reviewed the online repair video a few times then got started. Although only two were bad, I replaced all four terminal blocks. I removed the range top instead of using the built in kick stands. this left me much more room to work and I was able to clean the top of the range really well before getting started. Wires for the back terminals where short and a little difficult to use after cutting off the old terminal blocks. The terminal block mounting option for my style range included with the repair kit would not allow me to utilize the screw for the third wire on the left rear burner. I used a drill to carefully widen the hole in the mount to make the original screw fit as there are no screws included with the kit. This added the extra time to complete the repair. Over all the repair was simple to complete but having to modify the terminal block mount was dissapointing considering the web site selected parts for my specific model number. Still a bargain compared to what a service call or new purchase costs. I will be reparing my ranges from now on.
Was this helpful?
Thank you for voting!
Surface Indicator Light flickers and Element low heat
  • Robert from Waldorf, MD
  • Easy
  • 1- 2 hours
  • Pliers, Screw drivers
I previously replaced terminal blocks and elements so the infinite switch was the last stop before new purchase. I reviewed the online repair video. Unplugged the range and removed the three screws from the rear of the control panel. I Removed the knobs then removed two screws to release the front plate behind the knobs. I removed the two screws securing switch #1 and compaired to the new parts before removing wires. Wire locations were labled the same but in different sequence. I located the knob adapter for my knobs and set them asside. At first I thought the rod coming out of the new switch was too long and then figured out that the indentions allong the rod were to be broken off to the correct length. ( re-reading the included instructions was nearly useless - - not in plain language ) I used a pair of vice-grips clamped just below the length of rod I wanted to break off and it snapped off easily and cleanly for the most part. ( A word to the wise, this is some really soft metal at the breaks along the rod. I attempted a second break on one switch after mounting in the control panel and the thing broke off at the short end - - scary ) luckily I was still able to use it with my knobs and adapters. I relocated the switch wires to the new switch one at a time matching label to label ( L1, L2, H1, H2, P) then mounted the new switch into the control panel. I re-assembled the range and it is heating better than ever. Well worth the effort and minimal expense compared to a service call or replacement range.
Was this helpful?
Thank you for voting!
All Instructions for the 1199028
91 - 103 of 103