119749 Kenmore - Instructions

All Instructions for the 119749
121 - 135 of 227

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
My oven would glow, but wouldn't heat.
0 of 1 people found this instruction helpful.
  • Steve from Macomb, MI
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers, Socket set
I first removed the 2 screws that held the oven floor in place. Once removed, I remove the cover plate that covered the ignitor.

In order to get to the ignitor wires, I had to remove the drawer. Once the drawer was removed, I marked which wire went to which spot on the ignitor, then cut the wires. I then removed the old ignitor by removing 2 screws. I then attached the new ignitor with the 2 screws and attached the wires using the enclose wire nuts.

The complete process was very easy, taking less than half an hour. The part with shipping was just over $50. If I paid someone to fix my problem it would have cost at least $200. I'm sure galad I found this web site.
Was this helpful?
Thank you for voting!
Oven igniter failure
0 of 1 people found this instruction helpful.
  • Brett from Morgantown, IN
  • Really Easy
  • 15 - 30 mins
  • Socket set
Unplug electicity, Take out all inside pans, unscrew the burner arm, disconnect white power wires to the igniter. remover gas buner, detach the igniter and attach the new igniter to the burner arm. re assemble the burner arm, connenct the white wires to the white wires from the oven just below the igniter. Put all pans and guards back in oven, plug in and test.
Was this helpful?
Thank you for voting!
Oven not igniting
0 of 1 people found this instruction helpful.
  • Kirk from Saint Paul, MN
  • Easy
  • 15 - 30 mins
  • Wrench set
Unplug electric , remove old igniter, cut wires, shorten new igniter wires, strip insulation, wire nut together, attach new igniter, plug in electric, fire it up. Worked great.
Was this helpful?
Thank you for voting!
oven stopped lighting!!
0 of 1 people found this instruction helpful.
  • crystal from philadelphia, PA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Wrench set
wonderful went perfect!!!
Was this helpful?
Thank you for voting!
no flame
0 of 1 people found this instruction helpful.
  • joe from newport beach, CA
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
removed the old igniter, installed the new one. 15 minutes, piece o cake!
Was this helpful?
Thank you for voting!
Had a problem igniting the gas.
0 of 1 people found this instruction helpful.
  • Danny from Bremerton, WA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
took the old igniter out and swapped the connectors onto the new one. Kept the connectors close to the connector end to prevent them from being to close to the ovens heat.
Was this helpful?
Thank you for voting!
glo plug wouldn/t ignite
0 of 1 people found this instruction helpful.
  • William from Smyrna, DE
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
took out the old (2 screws) put clip on wires and put the new part in. Simple
Was this helpful?
Thank you for voting!
oven taking long time to start and shutting down while baking
0 of 1 people found this instruction helpful.
  • Merle from Monticello, IN
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Screw drivers
The oven igniter was working, the Sears repairman said by the phone the igniter was probley weak and not geting hot enough. Remove door ( 4 screws) Remove oven pan (4 Screws) remove burner sheld. remove lighter and cut wires. Install new. Remove storage drawer and splice new wires to the old at the back.
Was this helpful?
Thank you for voting!
oven would not heat up smell of gas
0 of 1 people found this instruction helpful.
  • peter from bronx, NY
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
i followed some of the tips provided, and added a few of my own. unplug stove from electric outlet. open oven door, remove wire trays. remove the two flathead screws, holding down the oven pan, it should slide out easily. remove oven burner(looks like wings)only one nut holding it in place with 1/4"nutdriver. remove igniter, 2 nuts as wel l with 1/4" nutdriver. cut wires, leave a good length, and strip(2 wires). install new igniter, strip the 2 wires as well, trim to size, and with the two wire caps provided, make wire connections. tuck any excess length of wires away from igniter. re-install all parts the were orginally removed. plug oven back into outlet. turn on oven, and presto, oven worked good as new. saved a couple of hundred dollars doing the repair myself
Was this helpful?
Thank you for voting!
Top part of stove worked but not the oven
0 of 1 people found this instruction helpful.
  • PAULA from AUSTIN, TX
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Wrench set
I googled most of the problem I was having. When I would turn on the oven I would have the orange glow from the igniter but I would never get heat. I ordered the part off this website...it arrived the very next day!!! 7 months pregnant I fixed the problem!!! My oven works beautifuly!! Just in time for the holidays! I saved so so muc h money doing it myself. U to can do it, good luck!!
Was this helpful?
Thank you for voting!
oven would not ignite
0 of 1 people found this instruction helpful.
  • Derrick from Houston, TX
  • Really Easy
  • 15 - 30 mins
  • Socket set
after reading other replies i was 100 percent sure that my igniter was the problem . just as others said it had a veryh dem glow . once i changed it the oven lit in about 5 seconds .very easy to install and saved at lease $ 400 on not needing a new stove. thanks parts select . com
Was this helpful?
Thank you for voting!
Oven would not come on
0 of 1 people found this instruction helpful.
  • Jim from Merced, CA
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
From the front I cut the wires going to the old igniter and removed it. Then I stripped insulation back 3/8 of an inch. Using the ceramic wire nuts that came with the new igniter, I connected the new wires to the existing. Then I installed the new igniter and the job was done. I turned on the thermostat and the oven ignited quicker than i t had for some time.
Was this helpful?
Thank you for voting!
The oven igniter would glow but the oven wouldn`t lite
0 of 1 people found this instruction helpful.
  • James from Circleville, OH
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
After finding your page and using your trouble shooting guide, it was easy getting the right part and the video helped a lot. Removed the over rack- removed two screws to remove the bottom- two screws to remove the burner. Clipped the two wires to the old igniter and removed the burner from the oven,removed the two screws holding the igni ter and installed new one. clipped the wires to length and renistalled the burner. Using the two wire nuts supplied put the wires togather and reinstalled the bottom. Everything went well lite first try with no poof sound. Just in time for Thanksgiving cooking. Got fast delivery of parts. Will uas again. Thanks Partselect.
Was this helpful?
Thank you for voting!
oven would not heat up.
0 of 1 people found this instruction helpful.
  • Paul from Warwick, RI
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
could not determine what part failed.Found Part Select on line useing Bing search.Using virtual repairman and typing in the problem it told me what I needed.Orderd that part on line and reieved it in TWO DAYS,can you believe that! Inatalled that igniter in 15 mins. and now it works like new. Thank You Part Select!!!!!!
Was this helpful?
Thank you for voting!
oven wouldn't light
0 of 1 people found this instruction helpful.
  • matthew from Plainfield, IL
  • Easy
  • 15 - 30 mins
  • Screw drivers
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I made sure I memorized just how the wires would re-connect with the wirenuts. I then re-assembled everything. Be sure to read all the instructions, especially how to properly install wirenuts. I was able to access the wire connections below the oven chamber through the drawer at the bottom of the range. This is an important detail.
Was this helpful?
Thank you for voting!
All Instructions for the 119749
121 - 135 of 227