119749 Kenmore - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Igniter would glow but no gas would turn on
0 of 1 people
found this instruction helpful.
-
Ronald from brockton, MA
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Removed 2 screws to oven bottom
Remove one nut that holds gas rail deflector
Removed 2 screws that held Igniterto the fuel rail
Cut 2 wires to the Igniter
attached 2 wires from new Igniter using ceramic wire nuts (Suplied with new part)
Install same as removal
Remove one nut that holds gas rail deflector
Removed 2 screws that held Igniterto the fuel rail
Cut 2 wires to the Igniter
attached 2 wires from new Igniter using ceramic wire nuts (Suplied with new part)
Install same as removal
Was this helpful?
Thank you for voting!
oven would glow but would take a long time to light, and you could smell gas
0 of 1 people
found this instruction helpful.
-
patricia from mayport, PA
- Easy
- Less than 15 mins
-
Wrench (Adjustable)
the igniter is real easy to put in
Was this helpful?
Thank you for voting!
Oven would not light
0 of 1 people
found this instruction helpful.
-
Christy from North East, PA
- Really Easy
- Less than 15 mins
It was pretty much a plug in. My husband had it done in a few minutes. I want to thank you for your great service with receiving the part.
The oven is working great and now I am back to baking.
Thanks for everything
Christy
The oven is working great and now I am back to baking.
Thanks for everything
Christy
Was this helpful?
Thank you for voting!
Igniter would glow but no gas would come out
0 of 1 people
found this instruction helpful.
-
Cornelius from Chicago, IL
- Easy
- Less than 15 mins
-
Nutdriver, Pliers, Screw drivers
First I removed the bottom plate of the oven to get a better view. I then removed the burner plate and the burner. Disconnected the igniter and put in new one it was real simple.
Was this helpful?
Thank you for voting!
No heat, gas smell in oven
0 of 1 people
found this instruction helpful.
-
David from Los Angeles, CA
- Really Easy
- Less than 15 mins
-
Nutdriver
Unplugged the oven
Removed racks and bottom plate
Removed two 1/4" fasteners on ignitor
Installed new ignitor with two 1/4" fasteners
Cut each wire on old ignitor one at a time and hook up using included wire nuts
Plug in oven
Test oven
If it works, put it back together
Removed racks and bottom plate
Removed two 1/4" fasteners on ignitor
Installed new ignitor with two 1/4" fasteners
Cut each wire on old ignitor one at a time and hook up using included wire nuts
Plug in oven
Test oven
If it works, put it back together
Was this helpful?
Thank you for voting!
There was a glow in the oven but the oven wouldn't heat up
0 of 1 people
found this instruction helpful.
-
sean from spring grove, IL
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
First I removed the two screws that held the element in place. I then pulled the element out about 3 inches and disconected the two wires. Take the old element out, and attach the new one. Assemble in reverse order.
Was this helpful?
Thank you for voting!
Lens cover for oven light broke.
0 of 1 people
found this instruction helpful.
-
Amy from Corona, CA
- Really Easy
- Less than 15 mins
Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.
Was this helpful?
Thank you for voting!
Oven would not heat up
0 of 1 people
found this instruction helpful.
-
Steve from Canton, IL
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Checked voltage supply to oven igniter, had 120 v
to oven igniter, but igniter was not glowing.
to oven igniter, but igniter was not glowing.
Was this helpful?
Thank you for voting!
wouldn't light.
0 of 1 people
found this instruction helpful.
-
brett from newbury pk, CA
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
First, I read all the instrutions that came with my replacement part from Parts Select thoroughly (twice) then follewed them like an experienced surgeon. I removed the lower drawr after turning off the gas and unplugging the stove and then took out the bottom panels inside the oven to expose the screws holding the ignitor coil. Removed it
... Read more
, then cnnected the new one to the existing wires as they were in the stove and the drawing in the instructions, then replaced everything in the reverse of them coming apart. Plugged it back in, turned the gas back on and now it,ll bake things again. YEAH!! Parts Select!!!
Read less
Was this helpful?
Thank you for voting!
Oven would not light; gas odor
0 of 1 people
found this instruction helpful.
-
Emily from Conneaut, OH
- Really Easy
- 15 - 30 mins
-
Wrench (Adjustable)
This was a very easy project.
-First, I removed the two bolts holding the old igniter. Second, I clipped the wires then stripped them. Next, I connected the wires with the wire nuts. Finally, I attached the igniter with the old bolts. I plugged it back in, and it worked better than ever. My husband was very impressed that I repa ... Read more ired our stove myself!
-First, I removed the two bolts holding the old igniter. Second, I clipped the wires then stripped them. Next, I connected the wires with the wire nuts. Finally, I attached the igniter with the old bolts. I plugged it back in, and it worked better than ever. My husband was very impressed that I repa ... Read more ired our stove myself!
Read less
Was this helpful?
Thank you for voting!
Oven wouldn't get hot..smell of gas
0 of 1 people
found this instruction helpful.
-
Eric from Chicago, IL
- Easy
- 15 - 30 mins
-
Wrench (Adjustable)
Replaced the flat style oven igniter. Turn off gas and unplug oven. Removed the broiler drawer, cut wires, unscrewed oven igniter (using a small/medium adjustable wrench), connected wires, fastened new igniter to bracket, spliced wire, twisted together, plugged oven back in, turned gas on, turned on oven after a few minutes...worked gre
... Read more
at.
Read less
Was this helpful?
Thank you for voting!
Would turn oven on, gas smell and would not light .
0 of 1 people
found this instruction helpful.
-
Michael from Forest City, PA
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
After removing heat shield, removed heating element (make sure you have the right bit, I stripped one of the screws). Cut wires , making sure to mark them. Reconnected and it worked like new! Saved a bunch of money,thank you!
Was this helpful?
Thank you for voting!
oven was slow on lite up
0 of 1 people
found this instruction helpful.
-
BILLY from DUCKHILL, MS
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
removed bottom plate in oven removed three screws and cut two wires.
Was this helpful?
Thank you for voting!
Oven would not light..
0 of 1 people
found this instruction helpful.
-
Jim from Oceanside, CA
- Really Easy
- 15 - 30 mins
-
Nutdriver
cut wires and removed the burner . Removed the ignighter and installed the new with nut driver. slipped the burner back in place and nutted the wires...Wallagh!!! fired right up...
Was this helpful?
Thank you for voting!
Oven was slow to light, strong gas smell, long time to reach set temperature
0 of 1 people
found this instruction helpful.
-
Gary Warren from Alexandria, VA
- Really Easy
- 15 - 30 mins
-
Nutdriver
Unplugged stove, removed floor of oven, removed two screws holding igniter, cut wires to igniter, installed new igniter, cut and stripped wires on new igniter and leads, connected new ingiter with supplied ceramic wire nuts, tested (worked perfectly!), then replaced oven floor.
It was a snap!
It was a snap!
Was this helpful?
Thank you for voting!