110C68132413 Kenmore Dryer - Instructions

All Instructions for the 110C68132413
16 - 30 of 211

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer turns off after 1-2 minutes
23 of 27 people found this instruction helpful.
  • Dixon from Santa Fe, NM
  • Easy
  • 30 - 60 mins
  • Nutdriver
I tried to follow directions followed by others on this site after diagnosing the problem via suggestions provided by users. I have a Whirlpool Duet dryer from 2002. We've had problems since moving about 3 years ago. I removed the front panel (lower) by unscrewing the two bottom screws (1/4" sheet metal screws). Then I took out the lint s creen and the metal tube/contraption immediately beneath to get access to the area where thermistor is located. See the drawing/chart to help you locate this. It's really easier than it seems. Make sure you have the chart/drawing for your model - it makes difference! The thermistor came out pretty easily with a nutdriver that has a swivel offset shaft. Ask your hardware store tool dept. about that one. Put everything back in reverse order of course and test either with/without the front panel re-attached. In my case it fixed at least part of the problem. I was able to get clothes almost dry with most settings but I have yet to install the moisture sensor to see if that helps in addition to the internal-bias thermistor. I am the kind of person that does one thing at a time so at least I now know the thermistor was bad. Good luck and hang in there with your own repair. It's a lot cheaper even if it takes you longer to do than a pro.
Was this helpful?
Thank you for voting!
Idler Pulley broke
21 of 26 people found this instruction helpful.
  • Keith from Richmond, VA
  • Really Easy
  • 15 - 30 mins
  • Socket set
I disconnect the power, then the vent pipe. I removed the back panel of the dryer to access the pulley and removed the belt. Replaced the back and put everything back together.
Was this helpful?
Thank you for voting!
dryer sounded like I was strangling a dog
18 of 21 people found this instruction helpful.
  • Lynda from Syracuse, NY
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
First, I watched a utube video of replacing the dryer belt. Then I went to Sears Hardware and couldn't find a part. Then I ordered the parts for my favorite online repair parts source - partselect.com. I had the part in one day! We did exactly what the video showed and also replaced the two wheels that looked like roller blade wheels. Pie ce of cake. Saved a $75 repair call plus whatever the parts would have been and spent about 20 minutes doing it. Back in business. Great for a 12 year old dryer! Buy the dryer kit!
Was this helpful?
Thank you for voting!
idler pully sqwieling
19 of 24 people found this instruction helpful.
  • Jerry Duty from Fort Walton Beach, FL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
once the back is off remove belt from tentioner and remove v clip. smooth shaft with wd-40 and scotch brite , then install new idler replace v clip
and your done !!!
Was this helpful?
Thank you for voting!
Squeaky Dryer
17 of 19 people found this instruction helpful.
  • Daniel from Hamilton, OH
  • Easy
  • 15 - 30 mins
  • Screw drivers
I looked for squeaky dryer within parts select and went with the 80%. I received the Maintenance Kit, replaced two rollers and it works like new. Amazing since this is the first time I have ever opened a dryer. The instruction sheet and parts were all I needed.
Was this helpful?
Thank you for voting!
parts took more than two months to get here.
17 of 19 people found this instruction helpful.
  • rodney from Mad River, CA
  • Very Difficult
  • More than 2 hours
I'm still waiting on my idler pulley. It arrived at Fed EX depot in Tracy CA on December 14th and has still not been shipped. So it is pretty fucking hard for me to install it! Maybe if you had customer service that would answer their phones or reply to my Emails would be helpful
Was this helpful?
Thank you for voting!
Dryer starts with loud squeak initially. Eventually there was a loud clank and dryer stopped.
16 of 17 people found this instruction helpful.
  • Victor from HOUSTON, TX
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Rather than remove the front panels, door, control panel and drum, I noticed 1/4" metal screws on the back panel. There were approximately 6 holding the back panel in place. I did have to remove the top panel as well before removing the back. Once removed I had complete access to the broken idler pulley assembly. I immediately saw the b roken pulley. I installed the new one with very little effort. Reset the belt according to instructions from the video. Reassembled, plugged in, hit start and enjoyed the sweet sounds of success. All told it took me about 20 minutes from start to finish.
Was this helpful?
Thank you for voting!
Dryer would not turn
15 of 18 people found this instruction helpful.
  • Kim K from Hurst, TX
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
My dryer starter squeaking in December 09 and the repairman told me that it would cost between $200-$500. I did not let him fix it as this machine is only 3 years old. When the part finally broke in April 10, I was ready to junk this and just buy a used dryer. My husband went on line and quickly figured out the part he would need to do the repairs. It cost under $20.00. Now my dryer is fixed and running and there are no squeaks. Thank you
Was this helpful?
Thank you for voting!
Dryer made a terrible screeching noise when tumbling.
13 of 14 people found this instruction helpful.
  • Richard from SAUGERTIES, NY
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
I followed the repair Vedic and took the drum out and replaced the pulls and bracket. Very straightforward job. Dryer is now as quite as the first day we bought it.
Was this helpful?
Thank you for voting!
Quick and simple - quickest $100 I've ever saved!
13 of 16 people found this instruction helpful.
  • Kelly from Waukegan, IL
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Wrench (Adjustable)
Removed the two screws under the lint trap
Opened the top (had to use flathead screwdriver to release latches)
Disconnected door switch harness from front panel
Removed 2 screws holding front panel on dryer
Lifted out dryer drum (previous belt had broken)
Vacuumed inside of dryer (found $3 in quarters!)
Put n ew belt around drum
Put drum back in dryer, using empty laundry soap bottle to support its weight
Looped belt around pulley and motor; secured pulley to dryer bottom
Made sure rear gasket thingy was aligned properly and drum turned freely
Put front panel back on
Re-attached door switch
Closed top and put screws back in under lint trap
Fired it up - WOOHOO!
Was this helpful?
Thank you for voting!
Scratches in Surface
83 of 228 people found this instruction helpful.
  • Michelle from Richardson, TX
  • Really Easy
  • Less than 15 mins
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this helpful?
Thank you for voting!
Bearings wore out of drum rollers
11 of 12 people found this instruction helpful.
  • Judy from Kalamazoo, MI
  • Easy
  • Less than 15 mins
  • Screw drivers
I raised the top of the dryer, removed the front, the belt and the drum. Slipped off old rollers, installed new ones and new tensioner. Reinstalled drum and belt, bolted front back on and closed the top.
Was this helpful?
Thank you for voting!
When using the dryer the cycle would stop and display E1 as the reason
13 of 18 people found this instruction helpful.
  • Joyce from Holbrook, NY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Unscrewed the bottom panelof the dryer and located the thermistor through the schematic for my machine. Removed the old one and put the new one in the same way. No more E1 problems and all cycles now complete themselves.
Was this helpful?
Thank you for voting!
Idler pulley wore out
10 of 11 people found this instruction helpful.
  • Peter from HUEYTOWN, AL
  • Very Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Removed the back panel and saw that the idler pulley was worn out. It only took me 5min. To replace, it was very easy to replace.
Was this helpful?
Thank you for voting!
Dryer squeeching very loud
9 of 9 people found this instruction helpful.
  • Michael from ENOLA, PA
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Socket set
Took off back of dryer Undid belt from belt adjuster pulled and took off adjuster put new one on redid belt and put back on dryer. Done
Was this helpful?
Thank you for voting!
All Instructions for the 110C68132413
16 - 30 of 211