1109875279A Kenmore Washer Dryer Combo - Instructions

REMOVE THE PANEL BETWEEN THE DRYER (above) and washer (below) two 3/8" metal screws. Remove the panel in able to remove the top panel of the washer. remove the top panel of the washer by releasing two screws in rear of washer, pull cover to front , unplug old lid switch. Put top panel on flat surface upside down. replace lid switch and replace the panel and BOB'S YOUR UNCLE. It is a lot easier than it seems.

I inserted the clip

Watched the video on the website... and did what it said to do. It was VERY helpful... It did not fix the problem... so now I'm on to the next possible solution. Also, provided by the website. The valve was the problem 85% of the time. The water level switch is the problem 10% of the time. The water level switch is what I ordered next.
Ordering is EASY and delivery is fast with available tracking of the shipment. Very nice...! -Eddie Campbell

Took off the four screws to get to the female clip and used pliers to squeeze it out. Next was using pliers to pinch out the male connector and place the new one in.

First off, I unplugged the AC cord and disconnected the Hot and Cold water hoses. I partially removed the back of the washer with a screwdriver. There were two screws holding the control panel in place and once they were removed it simply fell forward onto the top of the machine. That allowed me to pull the back plate free and remove the old water inlet valve. I had to first disconnect the two AC leads from the valve along with the small hose that supplies water to the tub. The small hose had a compression clamp on it that came off with pliers. After removing the two screws that secured the valve to the back of the machine the old valve simply came out. Insallation was the reverse. I will add that when removing the controll panel there are two S shaped clips (one either side of the panel) that need to be removed using a screw driver. Be careful not to push too hard as they may fall into the machine. I also replaced both the Hot and Cold wataer hoses. All in all it was a very easy repair. I read and followed the instructions of others that posted their experience right here which was a HUGE help-thanks everyone and thanks to Part Select for the prompt delivery. I orderd the part on a Sunday and received it on Tuesday-how awesome is that?!

Watched the video and followed the instructions. Everything went smoothly and the repair was done in under 15 minutes, less time than it took to mop up the water when it overflowed telling me that there was a problem.

First I put the square female end iof the door catch kit nto the square hole as snug as I could. Then I gently pushed the door against the piece until I heard it click in to place. That's it!! Sooooo simple--

The replacement part just snapped into place. (The old part had fallen out) It took less than 30 seconds to do the repair.

The instructional video that was attached with the part I purchased was spot on with very simple instructions. The inlet valve came with a metal bracket that was not needed for my model, so just tossed it. Was completed with replacement in about 30 minutes with help from my aspiring handywoman wife (would have taken 15 minutes without her)

Watch the video. Very, very easy

I removed the cabinet and agitator, layed the machine on it's back, removed the pump, motor and gearcase. I found a way to prop the gearcase up so it rested level, removed the cover, drained the old oil. I removed all internal parts, disassembled them and cleaned them. I reassembled the gearcase using the new uetral drain assembly, and replaced the oil. I made sure the brake assembly was pushed into position and then put the gearcase, motor and pump back in. I sttod the machine up, put the cabinet back on and tested the machine. It still did not spin, so it wasn't the coupler, clutch or nuetral drain assembly.

popped up top of dryer -- With pliers squeezed clips on inside of latch - - with screw driver pryed latch out -- just pused new latch in.......... Thanks to parts select for sending part sooo fast.. wife was happy.. Thanks, Dale

Installed part, now it works great!

my hany man did it....

Removed screws from top control panel. Tilted panel back. Unsnapped two retaining clips and pulled entire washer cover forward. Turned off water and uplugged washer. Disconnected hot and cold water supply. Disconnected supply tube from water inlet valve. Disconnected electrical hook-ups to water inlet valve. Removed water inletvalve. Installed new valve being careful to use new mounting plate supplied and making sure screw holes line up correctly. Re-connected all disconnects and it works like new!