110986 Kenmore - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Door catch on dryer door broke
14 of 14 people
found this instruction helpful.
-
Lynne from Jamestown, CA
- Really Easy
- Less than 15 mins
PartSelect sent me three different door catches with instructions for choosing the correct one. I did choose and simply inserted it into the slot and voile! All finished and it works great now! PartSelect had the part delivered the day after my order was placed. I would suggest doing business with them to anyone asking who they might c
... Read more
ontact for a part. I especially appreciated the ease of identifying and ordering from them. I was able to do all of this on-line via their website.
Read less
Was this helpful?
Thank you for voting!
drum stopped turning
15 of 17 people
found this instruction helpful.
-
Kenneth from Gerber, CA
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
First unplug dryer, then remove 4 screws along the back of the top and remove top and set aside. Next pull outward on the front until the front clears the drum and lift off the front and set to the side, careful not to stretch the wires to the door switch. Remove old belt and slip belt around the drum and line up with marks from old belt.
... Read more
Reach in under the drum under the motor and lift up the tensioner. Insert belt through tensioner and slip over the front of the shaft on the motor and release the tensioner. The belt should now be tight. Reinstall the front and top, plug in and test.
Read less
Was this helpful?
Thank you for voting!
Washmachine wouldn't spindry
15 of 17 people
found this instruction helpful.
-
Chuck from South Holland, IL
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers, Socket set, Wrench set
I removed three bolts from the transmission and two clips that hold the motor to the drive gear. I replaced the brake cam that had cracked and the lining. Now it works great ! Ordered part on Friday before two and it came Saturday at four.
Was this helpful?
Thank you for voting!
No cold water supply/slow cold water fill
14 of 15 people
found this instruction helpful.
-
Andrew from Virginia Beach, VA
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Unscrewed the two screws that hold the water lines to the valve. Unscrewed and lifted the control panel, popped the two spring clips that hold the back panel against the housing. Pulled the valve just outside the back panel. Took off the internal water line and moved it over to the new valve. Took off both hot and bold electric plugs a
... Read more
nd moved them to the new valve. With the old valve off, I sled the new valve into place and screwed it to the back panel. Put the spring tabs back on the back panel and screwed the back panel back together. Plugged it in, attached the water supply lines and tested it. Worked fine.
Read less
Was this helpful?
Thank you for voting!
my cold water did not run in the machine and it would not rinse
15 of 18 people
found this instruction helpful.
-
TONYA from DISTRICT HEIGHTS, MD
- Easy
- Less than 15 mins
-
Screw drivers
we looked at the video first then my husband fit the proble boy! was i excited! all the stores tried to get me to buy a new one. thanks partselets!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Was this helpful?
Thank you for voting!
Washer worked fine but wouldn't spin. Hot smell. I could turn tub by hand to help it get started and it would spin okay. Silver clutch cover was very hot to touch.
17 of 24 people
found this instruction helpful.
-
Kevin from Disputanta, VA
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
I pulled back off machine. A real pain. Not something you have to do although once the back is off, the whole cabinet just lifts off. Idealy: Remove agitator and reatiner clip, lay washer on it's side or face, Remove electrical connector form motor, remove two hoses from pump, (motor can be remove easily from transmission if desired. It's
... Read more
lighter), remove three 1/2" bolts, lift transmission w/clutch assembly out. Pay attention to orientation of flat washer and clip (remove). The cluch band is indside the silver cover. Pich together with pliers to relieve tension and lift out. There are three while pads that wear away and glaze over when they get too hot from slipping. Reassemble. Ths is from memory so I hope I didn't forget anything. Time to do it this way would probably only be 45 minutes.
Read less
Was this helpful?
Thank you for voting!
Water Inlet Valve
14 of 16 people
found this instruction helpful.
-
Ron from Hibbing, MN
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
The reason it took as long as it did was because the job is not in line as the work I normally do.
It would be a fairly easy job for an experienced repairman. (Taking the back off the washer was time consuming for me) The rest of the job was easy as the part was a perfect fit.
I remember having a problem blending hot/cold water ... Read more for some time. Most recently, while washing a load the water did not want to shut off. I can't remember how I diagnosed the water not shuting off as a problem along with the water temp control, but it is now repaired.
With the new valve installed, water temp select is now OK and the water now shuts off as normal.
It would be a fairly easy job for an experienced repairman. (Taking the back off the washer was time consuming for me) The rest of the job was easy as the part was a perfect fit.
I remember having a problem blending hot/cold water ... Read more for some time. Most recently, while washing a load the water did not want to shut off. I can't remember how I diagnosed the water not shuting off as a problem along with the water temp control, but it is now repaired.
With the new valve installed, water temp select is now OK and the water now shuts off as normal.
Read less
Was this helpful?
Thank you for voting!
water leaking from pump
15 of 19 people
found this instruction helpful.
-
michael from westmoreland city, PA
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Removed the clips. Pulled out the old pump. After trying to get the new pump on the shaft of the motor, I realized that some corrosion had built up on the motor shaft. I got a small tack hammer and very lightly tapped the shaft to remove the corrosion. The pump then slid on the shaft with no problem. Replaced clips. Job complete.
Th ... Read more e corrosion on the shaft cracked the plastic piece where the shaft connects and this is what caused the problem in the first place.
Th ... Read more e corrosion on the shaft cracked the plastic piece where the shaft connects and this is what caused the problem in the first place.
Read less
Was this helpful?
Thank you for voting!
Washer would not Agitate or spin out. Also noticed an oil leak.
14 of 16 people
found this instruction helpful.
-
Jonathan from BRANDON, VT
- Really Easy
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set
I followed instructions provided from Parts Select for removing and replacing the coupler assembly, and also instructions for changing the clutch assembly. I also took it's transmission apart (socket set and flat screwdriver required), drained the old oil, cleaned it, added new 90W gear oil. The instructions covered the swapping of parts
... Read more
very well. Cleaning up the oil spill took as long as changing the parts.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
improper or no hot water flow
16 of 23 people
found this instruction helpful.
-
Cynthia from Manchester, MO
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Wrench (Adjustable)
After taking the entire washer apart one time, we learned that we could take the top and front of the machine off only to repair it. I found Part-select online and with the model number locating the part was easy. It arrived within 3 days and with instructions I could easily replace the old part with a few tools. I spent dollars inst
... Read more
ead of hundreds for a new machine.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
water leaking during run cycle
13 of 15 people
found this instruction helpful.
-
michael from weymouth, MA
- Really Easy
- 15 - 30 mins
-
Pliers
flip machine back remove two spring clamps and hoses remove two spring clamps and water pump save $500.+on a new washer
Was this helpful?
Thank you for voting!
would not spin properly even with new coupling
16 of 24 people
found this instruction helpful.
-
david from o, AL
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
Removed capscrew in end of agitator shaft took cover off machine-[ unscrewed two screws holding down control panel, hinged back, pryed retaining clips out, rocked back machine cover.]
Removed motor mounting clips and pump hoses, swinging motor and pump out of the way. Removed 3 capscrews holding transmission, pulled transmission towa ... Read more rds me removing agitator shaft, disassembled clutch assembly - removing one cirlip then another, installed new clucth parts in same order
Removed motor mounting clips and pump hoses, swinging motor and pump out of the way. Removed 3 capscrews holding transmission, pulled transmission towa ... Read more rds me removing agitator shaft, disassembled clutch assembly - removing one cirlip then another, installed new clucth parts in same order
Read less
Was this helpful?
Thank you for voting!
Agitator moves freely in both directions
14 of 18 people
found this instruction helpful.
-
James from NAPERVILLE, AL
- Really Easy
- Less than 15 mins
-
Wrench set
First I removed the softener bin by pulling it up and off, then I removed the plastic seal by pulling it up and out, then I removed the 1/2 inch bolt with a ratchet and extension, then I removed the upper and lower agitator assembly from the machine and seperated the two by putting my feet on the lower agitator to hold it to the floor and
... Read more
pulling the upper agitator fast and firmly.
Sitting on top of the lower agitator I found the dog ear assembly. I pulled the dog ear assembly off and removed the yellow cap and existing dog ears.
Assembly was reverse.
Sitting on top of the lower agitator I found the dog ear assembly. I pulled the dog ear assembly off and removed the yellow cap and existing dog ears.
Assembly was reverse.
Read less
Was this helpful?
Thank you for voting!
dryer door would not latch
13 of 15 people
found this instruction helpful.
-
Robert from Livermore, ME
- Really Easy
- Less than 15 mins
my dryer door didn't latch for over a year. We were accustom to proping large objects against it. a friend told me to look on line. The close up pictures and parts diagrams were awesome. It was here in 4 days . Now my family thinks I am a hero. The end
Was this helpful?
Thank you for voting!
drum very loud when rotating
13 of 15 people
found this instruction helpful.
-
michael from indianapolis, IN
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
First I raised the top of the dryer(after unplugging the power cord) disconnected two wires to the front door switch and then removed two screws using a nutdriver. The front cover lifts up and while supporting the drum set the cover aside. Slide the belt off the drum and remove it. I then removed the two support roller tri rings and repl
... Read more
aced the rollers and tri rings and reassymbled the dryer.
It was a very simple repair.
Thanks Mike
It was a very simple repair.
Thanks Mike
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!