110986 Kenmore - Instructions

All Instructions for the 110986
76 - 90 of 2014

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washer would fill up, wash, then stop
22 of 31 people found this instruction helpful.
  • Glen from Plano, TX
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
I deduced the lid switch was the problem.

I removed the two screws holding the control panel on. Pulled the control panel back.
Disconnected the ground wire of the lid switch.
removed the two top clamps that hold the panel to the top of the machine.
Pulled back the casing (outside of the washer) and placed it on it's side on the floor. Here I could reach the switch. Removed old, installed new and reversed the process.

The part that gave me the biggest problem was setting the casing back on to the frame. You have to slide the front part in at the bottome, then lean back the rest of it.
Was this helpful?
Thank you for voting!
Temperature setting not working
19 of 23 people found this instruction helpful.
  • Robert from Buffalo, NY
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Took off back cover, thermostat was easily identified because of photos I've seen on website. Took 2 connectors off, removed 2 screws and removed old thermostat. That was pretty much it!

NOTE: Replacement thermostat 694674 has an adjustable temperature range setting that MUST be manually set prior to installing! You need to use the enclosed chart to find your original part# and make sure the setting is matched. My original part# 341146 had a "D" setting so I had to change but very easy to do.
Was this helpful?
Thank you for voting!
Drum was binding because of worn bearing supporting front of dryer drum
23 of 35 people found this instruction helpful.
  • Leslie from Townsend, GA
  • Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers
First I unplugged the dryer for safety, then I removed the top of the dryer, then removed the 2 hex head screws holding the font door panel onto the dryer. Then I disconnected the door safety switch. the rest was cake. I removed the old bearing and cut the new bearing and seal to the exact size of the old one. I used contact cement to gl ue the new bearing and seal into place. Reassembly was a breeze. End of job. Success!!!
Was this helpful?
Thank you for voting!
The Dryer would not start
17 of 18 people found this instruction helpful.
  • Dennis from Redondo Beach, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
First and most important was to unplug the unit.
I removed the 2 screws that hold the lint screen shoot to the top cover and then simply popped the top of the machine open using 2 screw drivers and
gently prying it up. I raised the top cover about 8 inches and supported it with a block of wood.
I opened the front loading do or and removed the 2 screws that hold the door actuator switch while holding the switch on the inside so that nothing would fall down into no mans land. Once the switch was loose I pulled it into view and could see that the actuator spring was broken. I used the search at the Part Select Web site and found the placement part very easy. I was amazed that the part was shipped and delivered to my house the very next day. The actuator spring simply snaps into place and I assembled it in the reverse order of removal, I removed the block of wood and snapped the top back into location and reinstalled the 2 screws for the lint screen shoot . I plugged the dryer in and it work perfect. I can't say enough about how well the experiance with Parts Select went, I will recommend them to others.
Was this helpful?
Thank you for voting!
Top Half of Agitator would not function without appying sideways pressure
18 of 21 people found this instruction helpful.
  • Donald from Fredericksburg, VA
  • Really Easy
  • 15 - 30 mins
  • Socket set
Heard about the website... 1 minute to find it, 10 minutes to order new cogs... 3 day wait for new parts... Rec'd Fedex, 15 minutes total to pull the agitator cover (bleach dispenser) then the bung cover with o-ring (just lift out) expose bolt, unskrew and remove top portion of agitator or entire agitator if it's easier. Seperate, remo ve black cog holder (slides up the spindle) and replace cogs one at a time just like the old ones. Reassemble in reverse and you are back in business. Saved the $75 deductible on my home appliance warrenty. You guys are the best... cheers...
Was this helpful?
Thank you for voting!
Agitator was barely agitating. Making a clicking noise.
17 of 18 people found this instruction helpful.
  • Charmaine from Slidell, LA
  • Easy
  • 15 - 30 mins
  • Socket set
Removed agitator cap. Removed bolt inside with socket wrench. Located plastic cogs Pulled out old cogs and slid in new cogs and put back together and works great. Easy to take apart and put back together. Very cheap repair. Cogs less that $4.00 plus shipping. Shipped next working day.
Was this helpful?
Thank you for voting!
The washer did not spin fast enough during the rinse cycle to adequately dry the load of clothes
17 of 19 people found this instruction helpful.
  • Richard from EL SEGUNDO, CA
  • A Bit Difficult
  • More than 2 hours
  • Socket set
I repaired my Kenmore washing machine replacing the clutch, Motor coupling and cogs. All of the parts came quickly and with good instructions. Best of all there were links to youtube repair walkthroughs. With out these step by step instructions this project would have taken much longer. Now the washer is like new! WATCH THE YOUTUBE PAUSE DO THE STEP AND REPEAT
Was this helpful?
Thank you for voting!
Would not spin
24 of 40 people found this instruction helpful.
  • floyd from Slidell, LA
  • Easy
  • 1- 2 hours
  • Pliers, Screw drivers, Socket set
Remove the nut from the top of the motor shift inside of wsher. then remove the wire harness plug. Take out three bolts side the shaft and motor out. Replace clutch and install in reverse order.
Was this helpful?
Thank you for voting!
The movers broke both water intakes off flush with the back of the machine
16 of 17 people found this instruction helpful.
  • Dennis from Oak Island, NC
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
took off two screws that held the top part on took the screws that held the back on 4 screws removed the one screw that held the replacement valve put the black mounting plate on the machine replaced screws very simple.
Was this helpful?
Thank you for voting!
One day, I found my dryer continued running after I opened the door. And next day, it stopped working at all. I thought it was time to buy a new one, since my dryer had been used for more than 15 years. But I was curious to know what went wrong, and recalled my friend told me he repaired the door
17 of 21 people found this instruction helpful.
  • Xiaobin from Cordova, TN
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Wrench set
My daughter found the video on youtube, which showed step by step repairing procedures. I just followed it and fixed my dryer in 15 min.
Was this helpful?
Thank you for voting!
Washer will agitate, but won't spin
18 of 24 people found this instruction helpful.
  • Mandie from Lewisville, NC
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I ordered the switch, which is what most people told me the problem was. I didn't have a multimeter, so I couldn't test the current one.

I removed the two screws from above the lid switch, removed the control panel screws on either side, and used a flat screwdriver to pry the top off by popping the clips.

The swit ch was easy to reach, and I compared the old and new switch after removing the paddle assembly. The new switch has three prongs, whereas my old one had two, so I put the gray wire terminal onto the bottom prong. I set everything down, plugged it in, and tested it, but still no spin cycle.

After some further research, I realized the problem was with the spin solenoid under the washer, or the red wire that leaves the lid switch and goes to the spin solenoid, also called a wig-wag solenoid. (This is a belt driven model, not direct drive.) It's not too common that the solenoids fail, but it is rather common that the wires break inside the insulation on this model.

Moral of the story is always ohm through the switches and wires before ordering replacement parts. (Remember, never ohm through a live circuit.)
Was this helpful?
Thank you for voting!
Water was leaking at the pump
17 of 21 people found this instruction helpful.
  • Paul from Painesville, OH
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Actually this is kinda funny. I ordered the part and it arrived when I was out of town on business. My 20 year old daughter tipped the washer up on its end, and replaced the pump herself in less than 30 minutes. Her only complaint was that no one told her to block the washer up as it almost fell on her.
Was this helpful?
Thank you for voting!
Washing machine leaking water
16 of 19 people found this instruction helpful.
  • John from Oklahoma City, OK
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
First, I'm glad I found PartSelect. The previous posts for this repair told me exactly how to replace the pump: I unplugged the washer and moved it out away from the wall (did not need to disconnect water hoses). Then I tilted the washer back and propped it up so I could get underneath. Using pliers, slid hose clamps back and disconne cted hoses from pump. Using a screwdriver, popped off two clips, top and bottom, that hold the pump in place. Pump then slides right off the shaft. Installation is the reverse. Make sure you align the shaft with the pump. Delivery of my part was FAST - ordered it and got it the next day!
Was this helpful?
Thank you for voting!
Leaking drain hose
16 of 19 people found this instruction helpful.
  • Steve from Cypress, CA
  • Really Easy
  • Less than 15 mins
  • Pliers
First I removed hose from drain, next I loosened the clamp at the drain hose connection at the washer. Removed hose. Have rags/towels as there is some residual water that will spill out of the washer. Reinstall in reverse.
Was this helpful?
Thank you for voting!
Washmachine wouldn't spindry
15 of 17 people found this instruction helpful.
  • Chuck from South Holland, IL
  • A Bit Difficult
  • 1- 2 hours
  • Pliers, Screw drivers, Socket set, Wrench set
I removed three bolts from the transmission and two clips that hold the motor to the drive gear. I replaced the brake cam that had cracked and the lining. Now it works great ! Ordered part on Friday before two and it came Saturday at four.
Was this helpful?
Thank you for voting!
All Instructions for the 110986
76 - 90 of 2014