11097584 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
dryer would not heat or turn off
9 of 12 people
found this instruction helpful.
-
michael from eldridge, IA
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set, Wrench (Adjustable)
removed front of dryer located igniter removed two screws disconnected wires then put new one in also replace thermal fuse and thermostat on back of dryer works great.
Was this helpful?
Thank you for voting!
No Heat
9 of 12 people
found this instruction helpful.
-
NICHOLAS from PARMA, OH
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers, Wrench set
I suspected a faulty igniter and disconnected the cable to the igniter and measured the resistance of the igniter and found it to be 70 ohms then I checked the voltage at the same cable towards the power source and found it to be 25 volts ac which should be 120 volts ac. Next I checked the radiant flame sensor and found it to be open (i
... Read more
t should be a closed circuit when cold). I removed the flame sensor (with the power off) using a small box wrench and found a broken lead. Replacing the flame sensor solved the problem.
Read less
Was this helpful?
Thank you for voting!
No heat
9 of 13 people
found this instruction helpful.
-
Philip from La Palma, CA
- Really Easy
- 1- 2 hours
-
Nutdriver, Screw drivers, Wrench set
Took everything apart, replaced the igniter flint, and still didn't get heat. Then found out the thermal sensor wasn't running a electrical current through it with voltmeter and just replaced that, now it we have heat again!
Was this helpful?
Thank you for voting!
Dryer hummed but drum wouldn't turn unless helped.
8 of 10 people
found this instruction helpful.
-
Leo from Ellicott City, MD
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable), Wrench set
Solution: electric motor replacement as the integral centrifugal switch lever (plastic cam) wears over time causing the start windings' switch poor contact. Took it all apart, (back panel, front and top) including lifting the drum out to completely expose the motor. Needed to wrench the plastic fan from the inside motor shaft. Tricky part
... Read more
was swapping the original pulley (6 rib belt, still good) for the one supplied for 4 rib belts. I needed to file another flat onto the other side of both motor shafts (old and new) to break them free, using a vice to secure the pulleys. The dryer works perfectly! It's a great dryer that can be repaired by a determined novice. The enclosed instructions were helpful, although if followed about cutting the original motor shaft to obtain its pulley might require drilling the shaft from the pulley = nonsense. Thanks again Parts Select.
Read less
Was this helpful?
Thank you for voting!
The Door Switch Actuator Spring had broken
8 of 10 people
found this instruction helpful.
-
Norman from Allen, TX
- Easy
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
I took the dryer apart by visually looking at it and removing screws, etc. until I had the top off and the front off. I took the dryer apart so I could get the part out and use it visually ascertain I was ordering the same part.
I bought the replacement part and only then did I have the instructions to take the dryer apart. I ... Read more t was further apart than the instructions said. I had to take the front off to retrieve the broken part which had fallen inside the front of the dryer.
I put the front back on the dryer and installed the new part, which, fortunately could only be installed one way. Once I had the two screws tightened into the part, the remainder was to simply follow the instructions that came from your web site and put the link filter and top of the dryer back on. Of course, I plugged in the dryer and checked to see that it ran before completing this.
I am amazed that I was able to find this part for a 30 year old dryer. The part hasn't changed at all. I guess, if you have a good part, there's no need to modify it.
I bought the replacement part and only then did I have the instructions to take the dryer apart. I ... Read more t was further apart than the instructions said. I had to take the front off to retrieve the broken part which had fallen inside the front of the dryer.
I put the front back on the dryer and installed the new part, which, fortunately could only be installed one way. Once I had the two screws tightened into the part, the remainder was to simply follow the instructions that came from your web site and put the link filter and top of the dryer back on. Of course, I plugged in the dryer and checked to see that it ran before completing this.
I am amazed that I was able to find this part for a 30 year old dryer. The part hasn't changed at all. I guess, if you have a good part, there's no need to modify it.
Read less
Was this helpful?
Thank you for voting!
Dryer not Drying
8 of 10 people
found this instruction helpful.
-
Manuel from Jurupa Valley, CA
- Easy
- 30 - 60 mins
-
Screw drivers
Replaced both Coils. Purchased M Series coils much less expensive buying coils together instead of seperately. Problem solved.
Was this helpful?
Thank you for voting!
The dryer door latch broke
9 of 13 people
found this instruction helpful.
-
Theresa from Topeka, KS
- Really Easy
- Less than 15 mins
-
Screw drivers
The most difficult part of this repair was making sure I purchased the right part !!! Part Select.com has a great website with pictures of almost every part you could ever need. I was able to select the right part and from there the repair was easy.
Was this helpful?
Thank you for voting!
Dryer would not turn on
8 of 10 people
found this instruction helpful.
-
Pam from Chandler, AZ
- Really Easy
- Less than 15 mins
-
Socket set
We took the screws off of the back, took out the thermal fuse and replaced it with the new one.
We watched a video of how to do it which made it so easy.
Works great!
We watched a video of how to do it which made it so easy.
Works great!
Was this helpful?
Thank you for voting!
gas dryer would fire, but shut down before getting warm enough to dry clothes
7 of 7 people
found this instruction helpful.
-
Glenn from Ossian, IN
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set, Wrench set
Removed lower front cover of dryer, located coils, removed old coils by disconnecting the wires and removing the hold down bracket screws. Pulled the old coils out replaced them with the new coils by aligning the index pins on the coils with the holes in the bracket then reattached the bracket and plugged the wires into the new coils. The
... Read more
n closed the cover on the front of the dryer. Dryer now ignites and stays on to heat up and dry clothes.
Read less
Was this helpful?
Thank you for voting!
No Heat After 10 Minutes
7 of 8 people
found this instruction helpful.
-
lawrence from GROTON, VT
- Really Easy
- 15 - 30 mins
-
Nutdriver, Wrench set
Shut off gas removed gas valve. Removed the coil retainer and installed the new coils. Reinstalled valve and checked. Found dryer worked fine.
Was this helpful?
Thank you for voting!
no heat was being produced
9 of 14 people
found this instruction helpful.
-
reinaldo from guttenberg, NJ
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Remove back panel n u can see the sensor and easy to replace thanks to the print out i was provided love this website
Was this helpful?
Thank you for voting!
Dryer stopped heating
7 of 8 people
found this instruction helpful.
-
Joseph from Austin, TX
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
(Always unplug dryer before making any repairs) I opened the dryer and checked the heating element. Making sure that the connection was good and nothing was damaged, I determined the problem was overheated wires. They melted and lots connection. I replaced them with the heating element wire connection kit. Easy to install and simple t
... Read more
o get right. I cleaned the dryer again with a vaccum cleaner, removing all the lint, and checked the vents, making sure they were clear...I turned the breaker on (it was tripped when the dryer overheated)and everything worked great.
Read less
Was this helpful?
Thank you for voting!
Broken Door Handle on Front of Dryer
13 of 26 people
found this instruction helpful.
-
Jeff from Wausau, WI
- Really Easy
- Less than 15 mins
Do to age and heat the dryer door handle was brittle and broke. Ordering was easy on line. Part was delivered faster tan expected. Oh and the repair time, Less than 1-minute.
Thanks for the great service.
Thanks for the great service.
Was this helpful?
Thank you for voting!
the glow ignitor would not cycle on
7 of 8 people
found this instruction helpful.
-
Georgio from Oradell, NJ
- Easy
- Less than 15 mins
-
Nutdriver, Pliers
I had an issue where I was not getting any power to my ignitor. After replacing the ignitor with a fresh one, the problem persisted. Next, I went hunting all the fuses and therrmostats for continuity. All seemed fine. So finally I decided to jump the flame sensor which is located on the outside of the flame tube. WHALLA! It ignited the g
... Read more
low plug. So with one 1/4"" nut driver I removed the single bolt from the unit, then I used a pliers to remove the two wires from the old unit. I replaced the sensor with Tue new unit and all was well. It took less than 5 min once I diagnosed the problem.
Read less
Was this helpful?
Thank you for voting!
My Kenmore dryer door catch was worn out, so the dryer door wouldn't stay closed, and I was unable to dry my laundry.
8 of 11 people
found this instruction helpful.
-
Carol from Golden Valley, MN
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
I identified the correct catch of the three that were included in the package by matching its number to that on the old catch that I had pried out of the door using a flat screwdriver. I centered the new catch over the square hole in the door and pressed it into place. Then I used some needle-nose pliers to twist and remove the metal pin
... Read more
that fits into the catch from the main dryer housing. I replaced that with the new piece included in the kit, gently tapping it into place with a hammer. The repair complete, the door worked perfectly. Thanks for your help and for the speedy delivery of the kit.
Read less
Was this helpful?
Thank you for voting!