11097584 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Loud sreeching and vibration
14 of 15 people
found this instruction helpful.
-
Robert from TUTTLE, OK
- Really Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
I just followed the videos I received with the order and everything went really well. This dryer was a little different than the video, but the process was the same. The HE3 does require 4 drum rollers and I had only ordered 2. However, there was only one bad roller, so I installed both on the back of the drum. The two front rollers are
... Read more
pretty easy to get to if they go bad. The idler pulley was completely worn out with an 1/8 inch groove worn off to one side. PartSelect made this an easy project!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Thermal fuse was bad.
16 of 22 people
found this instruction helpful.
-
Brad from Odessa, MO
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Did an Ohm test on the old Thermal Fuse found it to be bad. Replaced it with a new and the dryer is back to working great. Your suggestions saved approximatley $150.
Thanks for the help.
Thanks for the help.
Was this helpful?
Thank you for voting!
Dryer would leave clothes damp
15 of 20 people
found this instruction helpful.
-
Luke from Elmira, NY
- Easy
- Less than 15 mins
-
Nutdriver
First, I unplugged the dyer and then I removed all of the screws for the panel that covers the rear of the dryer. This exposed the cycling thermostat's location. I then removed the wires, one at a time so I would be able to put them back on in the same place. Then I removed the one screw using a nut driver and then put the new cycling the
... Read more
rmostat in place. It was pretty easy.
Read less
Was this helpful?
Thank you for voting!
Dryer gasket detached from screen
14 of 17 people
found this instruction helpful.
-
Richard from Duarte, CA
- Really Easy
- Less than 15 mins
Received in two days, open box, installed part. Pretty easy, fast service. I'm a repeat customer and will use these guys in the future.
Was this helpful?
Thank you for voting!
Dryer made a terrible screeching noise when tumbling.
13 of 14 people
found this instruction helpful.
-
Richard from SAUGERTIES, NY
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
I followed the repair Vedic and took the drum out and replaced the pulls and bracket. Very straightforward job. Dryer is now as quite as the first day we bought it.
Was this helpful?
Thank you for voting!
Burner would not go on on my Stack Set Dryer
16 of 24 people
found this instruction helpful.
-
Robert from North East, PA
- Really Easy
- Less than 15 mins
-
Screw drivers
Took out two front Panel screws and removed the panel. Removed Gas solenoid coil holding bracket by removing two phillips head screws. Disconnected the coil leads. and removed the coils. Connected the new coils to the leads and set in place. Replaced the holding bracket and the two screws. Replaced the front cover and the two front
... Read more
cover screws. Piece of Cake!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Lint has been bypassing the lint filter and building up in the fan (and duct)
12 of 12 people
found this instruction helpful.
-
David from PINETOWN, NC
- Really Easy
- Less than 15 mins
I noticed that drying time was increasing. I took the covers off the dryer to reach the fan and discovered that the squirrel cage fan buckets were packed with lint, and therefore not moving the air as intended. This was because the original lint filter caught most of the lint, but some bypassed the lint filter and then built up in the fan
... Read more
wheel buckets. The lint bypassed the lint filter because there was no felt gasket on the original filter as far as I can tell. I replaced the lint filter...and the replacement filter includes the felt seal (and fits tightly in the slide). The original lint filter has a provision for the felt seal, but I don't recall ever seeing it (and I did not see remnants of it in the fan or duct). As a matter of fact, I was always suspicious of how loosely the lint filter fit in the slide. The felt seal is not available as a replacement part from Maytag. That said, felt material 3/16"x1/2"x10ft is available from McMaster-Carr...and it fits nicely in the original lint filter.
Read less
Was this helpful?
Thank you for voting!
drum very loud when rotating
13 of 15 people
found this instruction helpful.
-
michael from indianapolis, IN
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
First I raised the top of the dryer(after unplugging the power cord) disconnected two wires to the front door switch and then removed two screws using a nutdriver. The front cover lifts up and while supporting the drum set the cover aside. Slide the belt off the drum and remove it. I then removed the two support roller tri rings and repl
... Read more
aced the rollers and tri rings and reassymbled the dryer.
It was a very simple repair.
Thanks Mike
It was a very simple repair.
Thanks Mike
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
dryer not heating up
12 of 14 people
found this instruction helpful.
-
Richard from New Windsor, NY
- Really Easy
- 15 - 30 mins
-
Screw drivers
Unscrewed 4 screws,pulled off front of machine.Unscrewed 2 screws holding coils on,unplugged coils,installed new coils,plugged in coils,reinstalled 2 screws for hold down brace.Reinstalled front cover,plugged dryer into outlet(remember to unplugged dryer before working on it).started up,instant heat,works great.thanks Partselect for helpi
... Read more
ng me out!!!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
The Dryer would not get hot.
14 of 20 people
found this instruction helpful.
-
Jerry from Bradenton, FL
- Really Easy
- Less than 15 mins
-
Nutdriver
I removed the two screws holding the access panel, and removed the access panel. Then removed the lower air duct. I then checked the burner, The solenoid was not opeing the valve for the gas. I order the coils, in two day I had the coils and installed them. The dryer is working great.
Other Parts Used:
Was this helpful?
Thank you for voting!
Door latch (female part) was broken.
11 of 11 people
found this instruction helpful.
-
JEANMARIE from BELLEROSE, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
I used a screwdriver to remove the old part and pushed the new part in with my fingers, it was very easy. If I could do it, anyone can. I was a lot cheaper then having a repair man come to house. I am very glad I found your site online, I will definitely be using your company again.
Was this helpful?
Thank you for voting!
The dryer was not fully drying
12 of 14 people
found this instruction helpful.
-
Michael from Chicago, IL
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers, Socket set
After replaceing several parts including the thermostats the last part I replaced the coils were the defective part. I originally metered out the themostats and they appeared to be okay but since this was my first time I thought I might have been mistaken. It turns out the last part I thought it could be was the part that was defective. I
... Read more
will say that it is very simple to replace any of the parts involved. The hardest part was trying to open the dryer itself. But after having to do it 3 times, I'm now a pro. I also replaced the drum belt and since I had it open I also replaced the belf idler with a newer modified idler rolller.
Putting the belt back on is easy, but it helps to view the video or a picture to understand how the belt goes around it.
Putting the belt back on is easy, but it helps to view the video or a picture to understand how the belt goes around it.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Rear dryer drum seal came out
17 of 29 people
found this instruction helpful.
-
William from Pontiac, MO
- Easy
- More than 2 hours
-
Screw drivers, Socket set
Used my Whirlpool Dryer User Instructions Manual and followed instructions and used the Cabinet Parts page to see the diagrams.
Was this helpful?
Thank you for voting!
Scratches in Surface
83 of 228 people
found this instruction helpful.
-
Michelle from Richardson, TX
- Really Easy
- Less than 15 mins
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this helpful?
Thank you for voting!
Would not start
12 of 15 people
found this instruction helpful.
-
Drew from Alachua, FL
- Really Easy
- Less than 15 mins
-
Nutdriver
First I tried a new switch, This did not fix the problem. Then I replaced the Fuse in the back of the unit.
Was this helpful?
Thank you for voting!