11094 Kenmore - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washing machine shook violently while on spin cycle
57 of 61 people
found this instruction helpful.
-
Tom from Bloomfield Hills, MI
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Disconnected the bracket screws that held the suspension springs in place - fed new springs into bracket and reattached. Local repairman told me that springs dont wear out, they break - wrong, they do lose their tension and thereby lose the ability to counterbalance the spinning load. Washing machine now spins like new - no wobble or shak
... Read more
e.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
door kept coming open dryer shuts off
95 of 176 people
found this instruction helpful.
-
RONALD from SALMON, ID
- Easy
- Less than 15 mins
-
Pliers, Screw drivers
use screwdriver topry plastic out plyers to pull out metal latch put new parts in
Was this helpful?
Thank you for voting!
Cold water slow to fill sometimes, Hot water no problems.
56 of 64 people
found this instruction helpful.
-
David from Knightdale, NC
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set, Wrench (Adjustable)
The hot water worked fine on the washer. The cold water would sometimes work/fill the tub, but would only produce a trickle of water at other times.
There were 2 screws to remove at the top back of the washer (attaching the console) two nut screws at the bottom left and right and another bottom center. There were also two screw ... Read more s on front of the console attaching it to the top of the washer. All of those are easy to remove.
The water dispenser (this is the opaque plastic part that fills the tub) has two rigid/hard plastic tabs that hold it to the back of the washer. They were difficult to move/push into the slots to release. It is probably a better idea to push the water dispenser down a bit and jiggle it off the top of the tub then to try and slide those plastic attachments over and down out of the slots on the back of the washer. I spent the most time doing that than anything else.
Also do not forget to detach the rigid steel clips that hold the console on top of the washer, a standard screwdriver or pliers work fine.
Unscrewed (with socket wrench) the mounting plate for the water inlet valve and pulled off the electrical connectors. Had a bit of trouble holding the hose clamp and pulling out the nozzle, but got it. I used pliers for this, but think in retrospect a vice grip would have been easier.
Put the new part in (it came with an installation sheet, very easy to follow) and remounted/hooked everything back up again. Reattached the back of the washer, screwed everything back in and put the console back on the top and screwed that in. Remember to put the steel clips back in that you remove in the beginning, otherwise the console will be loose.
Attached the Hot water hose, then the cold, turned on the water connections from the house and plugged the washer back in.
After pushing it back into position, I turned it on using the cold setting. A big glob of gray sediment shot out and the cold water was gushing in a lot stronger than it ever did before. Hot water came in faster too.
It fixed the problem. Working great now.
There were 2 screws to remove at the top back of the washer (attaching the console) two nut screws at the bottom left and right and another bottom center. There were also two screw ... Read more s on front of the console attaching it to the top of the washer. All of those are easy to remove.
The water dispenser (this is the opaque plastic part that fills the tub) has two rigid/hard plastic tabs that hold it to the back of the washer. They were difficult to move/push into the slots to release. It is probably a better idea to push the water dispenser down a bit and jiggle it off the top of the tub then to try and slide those plastic attachments over and down out of the slots on the back of the washer. I spent the most time doing that than anything else.
Also do not forget to detach the rigid steel clips that hold the console on top of the washer, a standard screwdriver or pliers work fine.
Unscrewed (with socket wrench) the mounting plate for the water inlet valve and pulled off the electrical connectors. Had a bit of trouble holding the hose clamp and pulling out the nozzle, but got it. I used pliers for this, but think in retrospect a vice grip would have been easier.
Put the new part in (it came with an installation sheet, very easy to follow) and remounted/hooked everything back up again. Reattached the back of the washer, screwed everything back in and put the console back on the top and screwed that in. Remember to put the steel clips back in that you remove in the beginning, otherwise the console will be loose.
Attached the Hot water hose, then the cold, turned on the water connections from the house and plugged the washer back in.
After pushing it back into position, I turned it on using the cold setting. A big glob of gray sediment shot out and the cold water was gushing in a lot stronger than it ever did before. Hot water came in faster too.
It fixed the problem. Working great now.
Read less
Was this helpful?
Thank you for voting!
The dryer would start to heat then the heat would stop
58 of 70 people
found this instruction helpful.
-
Theodore from Riverside, CA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Wrench set
I changed out the cycling thermostat and the high limit thermostat. Mainly because that was what my research indicated was the problem. I then found some more information online that indicated the gas solenoid valves were bad. I ordered them from you and replaced them. The problem was fixed.
In order to replace the valves ... Read more you need to remove the top panel. Two screws at the top of the front door assembly hold it on. Remove the screws, lift up on the front panel door assembly and move it to the side. The drum will rest in place. In the lower left corner, under the drum, you will see the solenoids. Two screws attach a plate that holds down the solenoids. Take the hold down plate off, disconnect the control wires attached to the solenoids and lift out the solenoid/control valves. To assemble everything, work backwards to the start. Good Luck
In order to replace the valves ... Read more you need to remove the top panel. Two screws at the top of the front door assembly hold it on. Remove the screws, lift up on the front panel door assembly and move it to the side. The drum will rest in place. In the lower left corner, under the drum, you will see the solenoids. Two screws attach a plate that holds down the solenoids. Take the hold down plate off, disconnect the control wires attached to the solenoids and lift out the solenoid/control valves. To assemble everything, work backwards to the start. Good Luck
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
bad water pump
55 of 62 people
found this instruction helpful.
-
carrie from magna, UT
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
We received the part we needed in a timely manner. First we took the back off the washer and found out later we didn't have to, because you can access the pump from the bottom of the Whirlpool washer and when we turned it on it's back a brass colored pin about 2" long fell out and we have no idea where it goes.Looking around the botto
... Read more
m frame we saw another pin in a plastic little cup mounted to the frame and another empty cup .So we changed the pump easy,put the pin in the empty cup and the washer runs great! That's our story.Still don't know what the pin is for,it's not on the parts schematic.
Read less
Was this helpful?
Thank you for voting!
Water drips inside washing machine, suspected the inlet valve needs to be replaced
52 of 55 people
found this instruction helpful.
-
PHU from Laguna Hills, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
Before ordering part, took the old valve out to make sure it looks similar to the one described online by Partselect. After ordering online, put things back together since I expected delivery would take 5-7 days. That night the water stopped dripping and has been OK ever since. I suspected that there was some rust in the electrical con
... Read more
nections. By disconnecting and reconnecting the terminal, the electrical connection is better and water stopped dripping. Still keep the new part just in case (which came overnight after I ordered it).
Read less
Was this helpful?
Thank you for voting!
timer knob broke off on washing maching
53 of 61 people
found this instruction helpful.
-
Beverly from Pensacola, FL
- Really Easy
- Less than 15 mins
I screwed the new knob on. No problem! But, was glad to see that replacement knob had metal part whereas original knob was all plastic. No wonder it broke after all these years of use. I don't expect the new knob to break. Thanks for carrying so many parts. It was easy to find.
Was this helpful?
Thank you for voting!
dryer would get hot for a while, then quit heating
56 of 70 people
found this instruction helpful.
-
Sharon from Houston, TX
- Easy
- 15 - 30 mins
-
Screw drivers
After reading about other people with this same problem I took a chance that this would be what was wrong with my dryer.I took off the front cover of the dryer by removing two screws. I located the faulty coils and simply plugged in the 2 new coils Tah-dah Probably coud have been done without even removing the front panel, but since it
... Read more
was off I vacuumed out the lint ( actually my husband did all of the above, but I tell a better tale than he does and I diagnosed the problem and ordered theparts)
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Our dryer started squealing and would then stop running.
55 of 69 people
found this instruction helpful.
-
Kelly from Aptos, CA
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Wrench (Adjustable)
After determining that the dryer motor was the issue I wrote down the part number and logged on to partselect.com.
I input the number into the search box and there was the exact motor I needed.
The price was fair and the delivery quick so I figured I would give yuo guys a shot and see how it goes.
The par ... Read more t showed up on time and as expected. It was well packed and most importantly - it was the CORRECT part.
I disassembled the dryer which involved removing the lint trap, pulling out the blower fan and removing the motor cover. The motor was held in with 2 metal screws and wiring harness.
I took the belt off of the tensioner and pulled out the old motor. The motor was mounted with 2 clips which snapped off with ease. Reassembly was a breeze since the motor fit perfectly- the entire transplant operation took all of about 35 minutes.
I crossed my fingers, turned on the gas, plugged it in and........SUCCESS!
Since the dryer was down for over a week the backlog of laundry was piled pretty high. This replacement motor would immediately be put to the test.
It has been 5 days of non-stop drying and no squeeks, no squeels and nothing but dry clothes!
Thanks to Part Select for getting everything right the first time. It made a potentially very bad experience turn out as good as I could have ever hoped.
I input the number into the search box and there was the exact motor I needed.
The price was fair and the delivery quick so I figured I would give yuo guys a shot and see how it goes.
The par ... Read more t showed up on time and as expected. It was well packed and most importantly - it was the CORRECT part.
I disassembled the dryer which involved removing the lint trap, pulling out the blower fan and removing the motor cover. The motor was held in with 2 metal screws and wiring harness.
I took the belt off of the tensioner and pulled out the old motor. The motor was mounted with 2 clips which snapped off with ease. Reassembly was a breeze since the motor fit perfectly- the entire transplant operation took all of about 35 minutes.
I crossed my fingers, turned on the gas, plugged it in and........SUCCESS!
Since the dryer was down for over a week the backlog of laundry was piled pretty high. This replacement motor would immediately be put to the test.
It has been 5 days of non-stop drying and no squeeks, no squeels and nothing but dry clothes!
Thanks to Part Select for getting everything right the first time. It made a potentially very bad experience turn out as good as I could have ever hoped.
Read less
Was this helpful?
Thank you for voting!
The washer wouldn't spin or agitate.
50 of 54 people
found this instruction helpful.
-
david from Monroe, MI
- Very Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set
Frist I disconnected the water lines and power cord. Then I leaned the washer back against the wall. Removed the 2 pump retainers and then the pump. Next removed the 2 screws from the motor retainers and pulled off the retainers and motor. Then removed the 3 bolts from the Gear case. Then removed the cap from the top of the agitator with
... Read more
a flat screw driver. Then removed the bolt from the top of the gear shaft. and removed the auger and agitator assembly. Then removed the gear case from the washer. Next removed the slip ring and then the clutch from the top of the gear case. Next removed the 1/4" screws from cover of gear case and removed the cover. Found the top gear bad. Ordered the new gear and pinion kit. Couldn't find any part #'s to match what PartSelect had. Ordered the gear that they should that fit most washers. The pics they had up looked the same as the one that was bad. Had the new gear in 3 days put it back together and it still wouldn't work right. Took it apart again and looked at it and found a small clip on the bottom side of the gear was upside down. Fliped it over put the gear back in and ran the washer with the gear case out and it worked. Put it back together again. And learned a good lesson always watch how you take things apart for when it's time to put it back together!
Read less
Was this helpful?
Thank you for voting!
Motor out
95 of 191 people
found this instruction helpful.
-
Jeff from Hutchinson, KS
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
I found that the dryer would not start turning by itself. Could manually help it start and it would run fine. Anyway, after a new set of rollers, belt, etc. found that the motor still would not start by itself. Ordered new motor and it was taken care of. You have to take the back off, remove the belt and remove the tumbler. After tha
... Read more
t, it is fairly easy. Two screws hold the motor down and then you can take the whole motor assembly out. Be careful removing the fan as it takes a 3/8 socket drive and it is plastic. Two clips hold the motor to the assembly. Needle nose pliers takes care of it. Replace and all should be good.
Read less
Was this helpful?
Thank you for voting!
the dryer only blew cold air
48 of 52 people
found this instruction helpful.
-
charles from waukesha, WI
- Really Easy
- 15 - 30 mins
-
Nutdriver
actually i found your site before i even looked at the dryer,thats how i knew to check for the thermal fuse.
I ordered the part and it was on my door in 36
hours,pulled the two wires off the old fuse and installed the new,put the back cover on and it has been working ever since,thanks ( your in my bookmarks)
I ordered the part and it was on my door in 36
hours,pulled the two wires off the old fuse and installed the new,put the back cover on and it has been working ever since,thanks ( your in my bookmarks)
Was this helpful?
Thank you for voting!
Washer wouldn't spin or agitate. Made louder-than-usual noise during those cycles.
45 of 49 people
found this instruction helpful.
-
Paul from Boonton, NJ
- Easy
- 1- 2 hours
-
Pliers, Screw drivers, Socket set
1. Read many other repair stories for similar symptoms. PartSelect Forum was an excellent resource.
2. Posted my problem on PartSelect Forum and awaited reply. Read replies, and followed provided link to step-by-step guide for the procedure. PartSelect forum moderators were excellent advisors!
3. Performed the ... Read more first half of the procedure to get to the diagnosed root cause. In some of the stories I had read, people had turned the washer on its back or tilted it up to get at the area from underneath. I am so glad I followed the conventional instructions, and left the washer standing and simply removed the cabinet. It was surprisingly easy. There's a reason why it was designed that way. I am also glad that I chose to remove the pump from the motor. While it is true that you don't *have* to remove the pump from the motor to get at the coupling...it hardly seems to make sense to remove the hoses instead. Removing the pump was incredibly easy, and by doing so, I never had to break any "wet" connections, and not one drop of water spilled over the course of the entire repair. (Even though I forgot to shut the water supply valves before I got started. Ooops! At least I remembered to unplug the power cord.)
4. But despite the open valves, the galoshes came into play not for their ability to repel water, but for their value as an electric insulator. I wrapped the galoshes around the handle of a long screwdriver when I discharged the motor's capacitor. :)
5. Ordered parts. Washed clothes in sink. Waited. Washed more clothes in sink. Waited some more. Washed more clothes in sink. Waited still more. Came very close to stopping payment to PartSelect because the very simple, commonly-requested part I ordered, which was supposedly in stock on the day I ordered it, didn't ship until the day it was supposed to arrive--even though I paid extra for expedited shipping. And I was never sent an e-mail to warn me that the parts were going to be delayed. And then to top it all off, rather than make up for some of the lost time caused by their own error, and ship it overnight, PartSelect chose to ship it 2nd day. All that good will generated by the excellent website completely evaporated by the failure to correctly complete the simple tasks that the business has needed to be good at since before computers were even invented. I will never use PartSelect again.
6. Prying the old coupler halves off of the motor and the washer took some effort, but was not overly difficult. I wound up removing the motor mounting plate in order to get better access to the half that was stuck on / needed to be attached to the drive train of the washing machine. Mounting plate was a breeze to remove and attach with a socket driver. I used one of those stubby flat-head screwdrivers to pry the old parts off. This was the one time where I thought it might have been easier to have the washing machine tilted up or on its back...but I muddled on through without even removing the bottom panel, and it wasn't too awkward. I used a large socket and a full-size hammer to not-so-gently tap the new parts into place. Putting all of the parts back together took a bit longer than it took to break them down, but it was easy. The instructions for putting the electronic control panel into test mode had been rolled up and taped to the cabinet inside the top panel. After I put the cabinet back on, I used those instructions to test all the cycles before fastening the top panel and testing the machine with an actual load. So far, so good...
2. Posted my problem on PartSelect Forum and awaited reply. Read replies, and followed provided link to step-by-step guide for the procedure. PartSelect forum moderators were excellent advisors!
3. Performed the ... Read more first half of the procedure to get to the diagnosed root cause. In some of the stories I had read, people had turned the washer on its back or tilted it up to get at the area from underneath. I am so glad I followed the conventional instructions, and left the washer standing and simply removed the cabinet. It was surprisingly easy. There's a reason why it was designed that way. I am also glad that I chose to remove the pump from the motor. While it is true that you don't *have* to remove the pump from the motor to get at the coupling...it hardly seems to make sense to remove the hoses instead. Removing the pump was incredibly easy, and by doing so, I never had to break any "wet" connections, and not one drop of water spilled over the course of the entire repair. (Even though I forgot to shut the water supply valves before I got started. Ooops! At least I remembered to unplug the power cord.)
4. But despite the open valves, the galoshes came into play not for their ability to repel water, but for their value as an electric insulator. I wrapped the galoshes around the handle of a long screwdriver when I discharged the motor's capacitor. :)
5. Ordered parts. Washed clothes in sink. Waited. Washed more clothes in sink. Waited some more. Washed more clothes in sink. Waited still more. Came very close to stopping payment to PartSelect because the very simple, commonly-requested part I ordered, which was supposedly in stock on the day I ordered it, didn't ship until the day it was supposed to arrive--even though I paid extra for expedited shipping. And I was never sent an e-mail to warn me that the parts were going to be delayed. And then to top it all off, rather than make up for some of the lost time caused by their own error, and ship it overnight, PartSelect chose to ship it 2nd day. All that good will generated by the excellent website completely evaporated by the failure to correctly complete the simple tasks that the business has needed to be good at since before computers were even invented. I will never use PartSelect again.
6. Prying the old coupler halves off of the motor and the washer took some effort, but was not overly difficult. I wound up removing the motor mounting plate in order to get better access to the half that was stuck on / needed to be attached to the drive train of the washing machine. Mounting plate was a breeze to remove and attach with a socket driver. I used one of those stubby flat-head screwdrivers to pry the old parts off. This was the one time where I thought it might have been easier to have the washing machine tilted up or on its back...but I muddled on through without even removing the bottom panel, and it wasn't too awkward. I used a large socket and a full-size hammer to not-so-gently tap the new parts into place. Putting all of the parts back together took a bit longer than it took to break them down, but it was easy. The instructions for putting the electronic control panel into test mode had been rolled up and taped to the cabinet inside the top panel. After I put the cabinet back on, I used those instructions to test all the cycles before fastening the top panel and testing the machine with an actual load. So far, so good...
Read less
Was this helpful?
Thank you for voting!
Dryer motor would not turn on
51 of 69 people
found this instruction helpful.
-
John from Bluffton, SC
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Wrench set
After looking at the schematic to see what was in line with the motor, I found the fuse as the first item. I pulled the fuse out and used a multimeter to ohm out the fuse. Upon using the meter I found that the fuse was bad. I typed into Google my part number that was on the fuse and the PartSelect Website came up as one of the choices to
... Read more
pick from. When the part arrived approx. two days later I installed the fuse by first unplugging the dryer and then removing the bottom panel and removing the fuse from the exhaust by using a small 1/4 inch wrench and pulling out the old fuse. I installed the wires on the new fuse and re-installed and put the 1/4 inch screw back in. I started the dryer after plugging it back in and it worked like it should have. Thank you for the part and I have recommended your website to other people already.
Read less
Was this helpful?
Thank you for voting!
Dryer wouldn't turn on
49 of 64 people
found this instruction helpful.
-
Olive from Williamsburg, OH
- Really Easy
- Less than 15 mins
-
Nutdriver
Removed the back of the dryer taking off the screws. Found the disposable thermal fuse. Unplugged the 2 blue wires connected to it. Removed the screws holding the part in. Replaced the old part. Reattached the blue wires. Put the back on the dryer. And voila! That simple!
I'm a 39 year old woman with absolutely no patience fo ... Read more r tedious jobs, but this was so easy I felt good about doing it. And felt even better for saving lots of money by doing the repair myself.
I'm a 39 year old woman with absolutely no patience fo ... Read more r tedious jobs, but this was so easy I felt good about doing it. And felt even better for saving lots of money by doing the repair myself.
Read less
Was this helpful?
Thank you for voting!