110894 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Drum would not spin to drain water
9 of 18 people
found this instruction helpful.
-
Gay from Apple Valley, CA
- Easy
- 15 - 30 mins
-
Screw drivers
Removed two screws and lifted the control console then tilted forward the shell. Removed two screws holding the latch cover and assembly then disconnected two wires. I played with the assembly until I discoved the element was toast. Ordered the part but when I got it I was confused because it had three prongs (two on one side and one
... Read more
on the other) when the burnt one had only one and one and I only had 2 disconnect wires. I thought I had gotten the wrong part but figured it out. Actually putting the assembly together was the easy part, trying to get the outer shell back together was a little tough. Between taking it a part, figuring out what was wrong and ordering and receiving the part was about three weeks. So when putting it all together took awhile but I did it and it works great.
Read less
Was this helpful?
Thank you for voting!
The dryer was squeaking and would not heat at all.
7 of 12 people
found this instruction helpful.
-
Steven from Oxnard, CA
- Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
The first thing I did was call my friend Donnie who manages some apartment buildings and who is always complaining about fixing things and getting the right parts to fix things. He told me what to order from PartsSelect and when the parts got here I called him up and he did the repair work.
He was reluctant to do the work at f ... Read more irst but after he found out I had ordered the parts from PartsSelect he was happy to do the work. "Their parts are always right and they always work," was what he said after he had my dryer working just like new. So if you know nothing about fixing things and buying parts just call PartsSelect and you will be fine. Just ask my friend Donnie!!!
He was reluctant to do the work at f ... Read more irst but after he found out I had ordered the parts from PartsSelect he was happy to do the work. "Their parts are always right and they always work," was what he said after he had my dryer working just like new. So if you know nothing about fixing things and buying parts just call PartsSelect and you will be fine. Just ask my friend Donnie!!!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
lod and heat caused cracks
5 of 6 people
found this instruction helpful.
-
Lawrence from Hull, MA
- Really Easy
- Less than 15 mins
replace basket with new one snapped in
Was this helpful?
Thank you for voting!
Dryer would not heat up properly. It would heat initially but once the heat was off it would not come on again.
5 of 6 people
found this instruction helpful.
-
Joseph from Chicago, IL
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
I followed the advice posted by other customers. I took the front off the dryer, put the door back in place and ran a cycle. I could see that the igniter was heating properly, but no gas was flowing. Based on what I read I concluded that it was a problem with one of the gas valve coils. It was relatively inexpensive to replace both (a
... Read more
nd the dry is 10 years old), so I didn't go to the trouble of determining the bad one. I replaced them both. Obviously I unplugged the dryer (no need to turn off gas). There were 2 screws that held the bracket in place which holds the coils. I disconnected the coils, removed the bracket screws, replaced the coils, reattached the bracket screws and reconnected the coils. I then reattached the front plate to the dryer. It was very easy and took about 20 minutes and I had never worked on a dryer before.
Read less
Was this helpful?
Thank you for voting!
No heat...
5 of 7 people
found this instruction helpful.
-
Charles from Long Beach, CA
- Easy
- 30 - 60 mins
-
Socket set
Removed and replaced both the thermostat sensor and the ignitor. Tested thej dryer and it worked. Replaced the front panel and it was good to go.
Was this helpful?
Thank you for voting!
Dryer would briefly get hot then stop heating
4 of 4 people
found this instruction helpful.
-
Randy from Katy, TX
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Wrench set
We've had this dryer for years. Still runs but for the past year, nothing would dry. It still turned on and blasted air, but this air was not getting hot. The typical suspects of clogged vents was not the issue because they were clear. I opened the back of the dryer to inpsect all the fuses with a multimeter, including the timer, and they
... Read more
tested normal. I did notice that the seal for the lint trap housing was detiorating so I bought a new seal.
Then I opened the front and disassembled the drum so I could reach and test the igniter and other fuses with the multimeter. There was a thick layer of dust at the bottom so that was all cleaned up first. I accidentally broke the igniter when cleaning up the dust. Then I tested all the fuses. They all also tested normal. Research told me that the coils may test normal when not in use.
After all that, I replaced lint trap housing seal, the coils, and the igniter. Then came the hardest part of reassembling the dryer. I tested the dryer with a load of laundry and the clothes came out dry and warm!
Then I opened the front and disassembled the drum so I could reach and test the igniter and other fuses with the multimeter. There was a thick layer of dust at the bottom so that was all cleaned up first. I accidentally broke the igniter when cleaning up the dust. Then I tested all the fuses. They all also tested normal. Research told me that the coils may test normal when not in use.
After all that, I replaced lint trap housing seal, the coils, and the igniter. Then came the hardest part of reassembling the dryer. I tested the dryer with a load of laundry and the clothes came out dry and warm!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
drum roller became lose and seperated from the shaft that supports it. it had to be replaced
5 of 7 people
found this instruction helpful.
-
Dillard C. from Vina, AL
- Easy
- 15 - 30 mins
-
Socket set
remove the front panel, belt [notice the way the belt is fasten] remove the tub, support bracket to the drum roller, and slide the new drum roller on and place the tre ring in the slot. then re-install everything in reverse
Other Parts Used:
Was this helpful?
Thank you for voting!
Old lent trap replaced with new...
4 of 4 people
found this instruction helpful.
-
Michael from MORGANTOWN, WV
- Easy
- Less than 15 mins
Popped out the old lent trap & popped in the new one..and walla perfect repair..
Was this helpful?
Thank you for voting!
Gas dryer would not heat - pilot lit briefly then went off
5 of 7 people
found this instruction helpful.
-
William from Chicago, IL
- Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Same as others.
1. Unplug dryer from power source
2. Use nut driver to remove two front screws at bottom of dryer
3. Disconnect cable connected to Secondary Coil (this is the coil towards the rear of the dryer)
4. Use angled phillips screw driver to loosen screws holding cap on top of the two coils. (Angled tool not ... Read more required but seemed easiest to me)
5. Slide top cap back towards lock screw to allow coil to be lifted out
6. Remove and replace secondary coil
7. Replace cap, tighten screws to lock in place, reconnect cable to coil
8. Restore power to dryer, test and confirm gas flame stays lit
9. Replace lower front panel on unit
PartsSelect a great resource to use for home repairs like these. My first time using site and doing this type of work, now PartsSelect my first source to go to on such items.
1. Unplug dryer from power source
2. Use nut driver to remove two front screws at bottom of dryer
3. Disconnect cable connected to Secondary Coil (this is the coil towards the rear of the dryer)
4. Use angled phillips screw driver to loosen screws holding cap on top of the two coils. (Angled tool not ... Read more required but seemed easiest to me)
5. Slide top cap back towards lock screw to allow coil to be lifted out
6. Remove and replace secondary coil
7. Replace cap, tighten screws to lock in place, reconnect cable to coil
8. Restore power to dryer, test and confirm gas flame stays lit
9. Replace lower front panel on unit
PartsSelect a great resource to use for home repairs like these. My first time using site and doing this type of work, now PartsSelect my first source to go to on such items.
Read less
Was this helpful?
Thank you for voting!
No Heat sometimes, But for a moment then None
4 of 4 people
found this instruction helpful.
-
Scott from Sacramento, CA
- Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
First and Foremost i was told that my problem was with the Thermal Fuse (Fix Ya.com), Then with the little Electrical knowledge I have thought Fuses don't turn on and off,If the fuse was bad i would get No Heat. (Even for a second) Fuses just don't turn on and turn off intermittently,when they go there done! So after a little research i d
... Read more
ecided to order the gas coil valve. I tilted the top up, two screws on the front panel, took that off and the valves were exposed,(bottom left) two screws too remove bracket then installed new coils on bracket,put back together and I Have Heat Again! NO problems what so ever since new install. I would say having not been for cleaning lint build up inside the machine (been 6 years) the Whole project took me Ten Minutes.
Read less
Was this helpful?
Thank you for voting!
Old filter and cover had rusted retaining clips and rusted out sections
4 of 4 people
found this instruction helpful.
-
david from HAYWARD, CA
- Very Easy
- Less than 15 mins
Removed old assemblies manually and replaced with new. Very easy and the parts fit perfectly!
Was this helpful?
Thank you for voting!
Dryer heat would go off and timer would not move. Dryer would continuously run
4 of 5 people
found this instruction helpful.
-
chuck from smithtown, NY
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Replaced coils on gas valve.
Was this helpful?
Thank you for voting!
Too much drying time, not hot enough
4 of 5 people
found this instruction helpful.
-
John from Floyd, VA
- Easy
- 15 - 30 mins
-
Screw drivers
I removed the Drier Door and removed the Front Drier Panel exposing the Gas Valve & associated parts. I removed two (2) screws holding the Gas Valve Coils in place & replaced the 2 terminal coil, then replaced the screws, Front Cover & Drier Door. I liked the results so much, I ordered the other Gas Valve Coil and will replace it also w
... Read more
hen it arrives.
Good trouble shooting information.
Good trouble shooting information.
Read less
Was this helpful?
Thank you for voting!
would only heat for about 7 minutes.
4 of 5 people
found this instruction helpful.
-
Craig from ARMA, KS
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
I replaced the thermos fuse, thermostat, igniter kit, and the M series
new style coil kit. The problem was the M series coil kit. I replaced
the other parts because this dryer is over 10 years old. I also brought
the radiant flame sensor. I spent $126.19 in parts plus shipping. If I just
just replaced the coil kit it ... Read more would have 18.61 plus shipping. A new gas dryer like I have would cost about $459.00. I hope to get many more years out of this dryer. The hardest part of this repair for me was getting the front panel back on. I saved the parts that were good for futher repairs. I replaced the drum belt several years ago, still looks in good shape. I think this is a great DIY site. Just follow their instrutions. Somtimes I'll take a picture of the part before I remove it, just to be sure I replace it right.
new style coil kit. The problem was the M series coil kit. I replaced
the other parts because this dryer is over 10 years old. I also brought
the radiant flame sensor. I spent $126.19 in parts plus shipping. If I just
just replaced the coil kit it ... Read more would have 18.61 plus shipping. A new gas dryer like I have would cost about $459.00. I hope to get many more years out of this dryer. The hardest part of this repair for me was getting the front panel back on. I saved the parts that were good for futher repairs. I replaced the drum belt several years ago, still looks in good shape. I think this is a great DIY site. Just follow their instrutions. Somtimes I'll take a picture of the part before I remove it, just to be sure I replace it right.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer makes squealing noise, finally the motor seized up.
4 of 5 people
found this instruction helpful.
-
Anthony from PITTSTON, PA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
My dryer started squeaking and I thought it was the drum rollers, so I bought a set. When I attempted the repair and got as far as removing the dryer drum and I decided to spin the shaft on the motor and that was where the squealing was coming from. I put the rollers on and reassembled the dryer. One day later the motor seized up. Ordered
... Read more
a new motor and installed it with no problems. The nut on the back of the motor ended up being a 20mm wrench. Motor cost me $105.56 and the maintenance kit (ps37308) (2 rollers,4 clips, button clip, new idler pulley and belt) cost $32.08. It cost a total of $137.64 in repairs with no labor costs and I accomplished it in under an hour. Minor handyman skills needed or find a friend who is handy. My dryer is 14 years old and now is running like new again. I used the 50% rule, if a repair exceeds 50% of the cost of a new machine, replace it, if the repair can be done for less than 50% of the cost of a new on, fix it.
Read less
Was this helpful?
Thank you for voting!