110894 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
My dryer conked. Would not turn on, but before that happened it was taking way too long to dry the clothes and the dryer would stop in the middle of a cycle.
7 of 9 people
found this instruction helpful.
-
brenda from Newman Lake, WA
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
Went on this website and found a story that was similar. I ordered the parts which arrived quickly and I replaced the Thermal Fuse and heating element and it was fixed! The whole repair cost me $24.88! Way cheaper than calling a repair man.
Heater thing was part # 3387134
and the fuse was 3392519
Heater thing was part # 3387134
and the fuse was 3392519
Was this helpful?
Thank you for voting!
Dryer made a terrible squealing noise
7 of 9 people
found this instruction helpful.
-
Will from Charlotte, NC
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers, Socket set
Took a bit to first figure out how to get the front of the dryer off in order to access the motor, wheels, and belt, but found a "how-to" online. Once I had that, the rest was easy.
Lubricated motor and guide wheels but squealing still there. Then noticed the "idler pulley assembly" (the part that keeps the belt tight against ... Read more the drum) looked a bit old and worn. Ordered a replacement part on this site because it was much much cheaper than a service call, installed it.... and NO SQUEAL!!!
Lubricated motor and guide wheels but squealing still there. Then noticed the "idler pulley assembly" (the part that keeps the belt tight against ... Read more the drum) looked a bit old and worn. Ordered a replacement part on this site because it was much much cheaper than a service call, installed it.... and NO SQUEAL!!!
Read less
Was this helpful?
Thank you for voting!
No Heat
7 of 9 people
found this instruction helpful.
-
Ken from Bixby, OK
- Easy
- More than 2 hours
-
Nutdriver, Screw drivers, Socket set
Thermal fuse was blown so I replaced it. Still no heat. Hi-Limit thermostat and Cycling Thermo. had continuity as did flame sensor. Igniter tested 66ohms. I placed a wire jumper across the Hi-Limit and the igniter glowed, solenoids opened and gas came on. I orderd the Hi-Limit and since both "overheating" limiters were defective I de
... Read more
cided to order the cycling thermo just in case. The Hi-Limit was received in 2 days but the Cycling Thermo was backordered. In the meantime my wife got antsy so I went ahead and installed the Hi-Limit and put her back in service... ...for one load. I wasn't certain if I had fried the "limiters" again but since they had continuity and I could measure continuity all the way to the Igniter I decided that it HAD to be the cause. I ignored the flame sensor since it never came into play without the igniter glowing... The igniter arrived and measured 56ohms. Hmmm... After installing the problem was solved. Word of advice: If the thermal fuse is blown and even if all else in the circuit SEEMS ok, go ahead and order the Fuse, Hi-Limit and Cycling Thermos, and the Igniter. It will take you about 30 minutes to install and you'll reduce your out-of-service time! Good luck!
Read less
Was this helpful?
Thank you for voting!
The dryer start but it did not stay on.
7 of 10 people
found this instruction helpful.
-
Luis from VALDOSTA, GA
- Really Easy
- Less than 15 mins
-
Nutdriver
I replaced the push start buttom,but it still had the same problem,so I went to the motor and found the burnt wire and bingo,we are happy again thanks to your website.
Was this helpful?
Thank you for voting!
not heat
7 of 10 people
found this instruction helpful.
-
Sarah from Merrimac, MA
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
For the Ignitor - As involved as taking the dryer completely apart sounded, it was super easy. 1-take out the lint trap and remove the two screws there. 2-Pop open the top with a screw driver and swing the top completely over/back. 3- remove the two screws holding in the front panel and remove the panel. 4- loosen the belt by pushing on t
... Read more
he tension roller under the drum on the right and remove the drum (its super light) use the belt as a handle. 5- remove the screw holding in the ignitor and replace it with the new one. Be careful to not touch the new ignitor. Then go backwards putting it back together.
Read less
Was this helpful?
Thank you for voting!
Dryer would not start.
7 of 10 people
found this instruction helpful.
-
Rebecca from Scarsdale, NY
- Really Easy
- 15 - 30 mins
-
Screw drivers
Unplug dryer from mains. Remove the back of the dryer. Thermal fuse is located on the left hand side near the bottom as you face the back of the dryer. Remove fuse and connect new fuse. Never repaired an appliance before and this was so easy!
Was this helpful?
Thank you for voting!
Dryer got hot then heat would shut off
6 of 7 people
found this instruction helpful.
-
Douglas from Fernley, NV
- Really Easy
- 30 - 60 mins
-
Nutdriver, Socket set
Sensor is in the front lower left. Gas off, electicity off. Removed two screws for the filter, pry/lifted the top up and taped it too the overhead cabinet, removed two screws inside top of front panel, lifted pandel with door closed staight off. Two screws to remove the flame sensor braket. unplug the old sensor install the new one and r
... Read more
everse everything. With others suggestions I purchased temperature switches etc. but the radiant flame sensor was the problem. I now have some spare switches for future. Excellent company and very quick service. Oh, Sears wanted 200.00 just for the service call, I live rural.
Read less
Was this helpful?
Thank you for voting!
the dryer would run for about two mints and shut off
7 of 10 people
found this instruction helpful.
-
Albert A Little from brookfield, MA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
removed the back of the dryer and the thermal fuse and the dryer cycling thermostat were right next replace them and the dryer work like new my dryer is 40 years old and saved a ton of money fixing it myself
Other Parts Used:
Was this helpful?
Thank you for voting!
Start windings burnt out on original motor (dryer would not start)
7 of 10 people
found this instruction helpful.
-
Frank from Smyrna, TN
- Easy
- 1- 2 hours
-
Pliers, Screw drivers, Socket set, Wrench (Adjustable)
The repair was fairly straight-forward. I removed the front of the dryer, lifted the top off, and then released the tension off the belt dy depressing the pulley arm. Once the belt was off, the drum came right out and then it was on to unhooking the wiring from the old motor. Very simple up till this point. The snag came when I went to un
... Read more
thread the impeller fan off of the old motor shaft. It was permanently sealed onto the shaft so I had to cut the old shaft into using a reciprocating saw was a metal-cutting blade. Once this was done the new motor installed easily exactly like the old one was mounted. I had to also purchase a new fan due to the fact that I was unable to remove the cut shaft from the old fan. All parts worked great and the dryer assembled back together easily. Works like a new dryer now.
Read less
Was this helpful?
Thank you for voting!
Broken Motor Pulley
7 of 10 people
found this instruction helpful.
-
Mark from PELHAM, MA
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Socket set
Removed back panel of the dryer-reached my hand to the back of the motor shaft, put 7/16 wrench on it to hold the shaft while I removed the broken pulley with pliers. Very easy fix-the tech on Utube took the entire dryer apart totally unnecessary. If that is what the factory tells its tech"s to do its no wonder why the labor charge woul
... Read more
d be thru the roof.
Read less
Was this helpful?
Thank you for voting!
Dryer had no heat at all. This is an older gas dryer.
5 of 5 people
found this instruction helpful.
-
todd from MILFORD, PA
- Really Easy
- Less than 15 mins
-
Wrench set
Cleaned out years of fuzz behind lower access panel and noticed where the igniter sits there is a metal tube about 1 inch in diameter. It had rust on the end and was starting to flake away. Found some helpful hints about how to test the igniter. Very easy, just used an ohmeter. Unplugged the 2 pin wire connector and checked for continuit
... Read more
y. 1 lead on 1 pin and the other on the other pin., igniter side not the harness side from the dryer. A good igniter should read less than 5 ohms. I don't know the spec. exacttly, but it should not read open or infinite resistance. My meter read an open circuit. Removed the tube and igniter assembly, mine only 2 small bolts. I found the igniter element cracked. Ordered and installed igniter and tube assembly. This was a very easy install. 20 year old dryer works great and it's better than spending $500.00+ on a new one.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
not drying all the way, not getting hot enough
6 of 8 people
found this instruction helpful.
-
robert from cedar lake, AL
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
loosened two screws on back of top,lifted top away from front panel.it just lifts off front corners,removed two screws at top corners.lift front panel up and out,this panel supports dryer tub,remove slowly,unplug door switch parts are located left side bottom two screws holding in had to have wife hold drum up to put front panel on
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer would only heat at start up for one cycle
6 of 8 people
found this instruction helpful.
-
Rob from Henderson, NV
- Really Easy
- 30 - 60 mins
-
Nutdriver
Ohmed coils and both had continuity so I changed radiant heat sensor. No bench test for Radiant Heat sensor. Same problem. Changed both coils and dryer works fine. Weak coils were my problem. I read thru the same issues in Parts Select forum and it said Radiant Heat sensor was problem 25% of the time. With coils having continuity and no o
... Read more
hm value specified for coils I made wrong choice but, I have spare parts and look for another 10 years of life in the dryer. Nice to have this forum to research appliance repair. Very helpful for parts location and installation. Dishwasher is next!
Read less
Was this helpful?
Thank you for voting!
No heat, would not light because igniter burnt out
6 of 8 people
found this instruction helpful.
-
anthony from Port Arthur, TX
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers
Unplug dryer. Remove the front bottom panel of dryer 2 screws, then unplug wire connector to the old igniter then unscrew one screw holding ignitor then wiggle out. Open new igniter wiggle back in place insert screw tighten, (getting this screw back in is a little hard) replug wire connector to new igniter replace front panel with two scr
... Read more
ews. Plug in dryer and there you go drying clothes again. Wife all happy again.
Read less
Was this helpful?
Thank you for voting!
lod and heat caused cracks
5 of 6 people
found this instruction helpful.
-
Lawrence from Hull, MA
- Really Easy
- Less than 15 mins
replace basket with new one snapped in
Was this helpful?
Thank you for voting!