110894 Kenmore Dryer - Instructions

All Instructions for the 110894
61 - 75 of 949

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Thermal fuse was bad.
16 of 22 people found this instruction helpful.
  • Brad from Odessa, MO
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Did an Ohm test on the old Thermal Fuse found it to be bad. Replaced it with a new and the dryer is back to working great. Your suggestions saved approximatley $150.

Thanks for the help.
Was this helpful?
Thank you for voting!
Burner would not go on on my Stack Set Dryer
16 of 24 people found this instruction helpful.
  • Robert from North East, PA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Took out two front Panel screws and removed the panel. Removed Gas solenoid coil holding bracket by removing two phillips head screws. Disconnected the coil leads. and removed the coils. Connected the new coils to the leads and set in place. Replaced the holding bracket and the two screws. Replaced the front cover and the two front cover screws. Piece of Cake!
Was this helpful?
Thank you for voting!
dryer door would not latch
13 of 15 people found this instruction helpful.
  • Robert from Livermore, ME
  • Really Easy
  • Less than 15 mins
my dryer door didn't latch for over a year. We were accustom to proping large objects against it. a friend told me to look on line. The close up pictures and parts diagrams were awesome. It was here in 4 days . Now my family thinks I am a hero. The end
Was this helpful?
Thank you for voting!
drum very loud when rotating
13 of 15 people found this instruction helpful.
  • michael from indianapolis, IN
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
First I raised the top of the dryer(after unplugging the power cord) disconnected two wires to the front door switch and then removed two screws using a nutdriver. The front cover lifts up and while supporting the drum set the cover aside. Slide the belt off the drum and remove it. I then removed the two support roller tri rings and repl aced the rollers and tri rings and reassymbled the dryer.
It was a very simple repair.

Thanks Mike
Was this helpful?
Thank you for voting!
squeaky and very loud noise
13 of 15 people found this instruction helpful.
  • Jimmie from Lucerne Valley, CA
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Screw drivers, Socket set
first we printed out directions from a couple of online repair sites that had pictures.
We followed the directions to remove the front of the dryer and removed the belt off the drier and then took out the drum. We had a hard time trying to keep the rear seal on so used CLOTHES PINS to put on the seal, then we added the adhesive repla cing the clothes pins until the whole seal glued. Since the drum was already out, we put it in the sun to really dry the glue.
Next we attacked the drum support rollers. We removed the back of the dryer and used a 9/16" socket with an extention to remove the back nuts.
We took out the shaft, used sandpaper on it and then replaced the triangle clips and the support rollers.
Then put the back on again, then the front, making
sure the drum fit on the front. You have to then figure out the belt, with the rubber side down, and then work with the tensioner, which took my poor husband a while. Then lowered the top, put the clips back on and the bottom, making sure we turned the drum. It was a success after about 3 hours. You can do it a lot easier with pictures.
Was this helpful?
Thank you for voting!
Door latch (female part) was broken.
11 of 11 people found this instruction helpful.
  • JEANMARIE from BELLEROSE, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I used a screwdriver to remove the old part and pushed the new part in with my fingers, it was very easy. If I could do it, anyone can. I was a lot cheaper then having a repair man come to house. I am very glad I found your site online, I will definitely be using your company again.
Was this helpful?
Thank you for voting!
The Dryer would not get hot.
14 of 20 people found this instruction helpful.
  • Jerry from Bradenton, FL
  • Really Easy
  • Less than 15 mins
  • Nutdriver
I removed the two screws holding the access panel, and removed the access panel. Then removed the lower air duct. I then checked the burner, The solenoid was not opeing the valve for the gas. I order the coils, in two day I had the coils and installed them. The dryer is working great.
Was this helpful?
Thank you for voting!
lint coming out duct outside
14 of 20 people found this instruction helpful.
  • john from hamlet, NC
  • Really Easy
  • Less than 15 mins
one of ears that holds filter was broken leaving a small gap so lint went into duct work so i replaced the cover and filter is now held in place letting the filter do its job trapping the lint
Was this helpful?
Thank you for voting!
The dryer was not fully drying
12 of 14 people found this instruction helpful.
  • Michael from Chicago, IL
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers, Socket set
After replaceing several parts including the thermostats the last part I replaced the coils were the defective part. I originally metered out the themostats and they appeared to be okay but since this was my first time I thought I might have been mistaken. It turns out the last part I thought it could be was the part that was defective. I will say that it is very simple to replace any of the parts involved. The hardest part was trying to open the dryer itself. But after having to do it 3 times, I'm now a pro. I also replaced the drum belt and since I had it open I also replaced the belf idler with a newer modified idler rolller.

Putting the belt back on is easy, but it helps to view the video or a picture to understand how the belt goes around it.
Was this helpful?
Thank you for voting!
dryer not heating up
12 of 14 people found this instruction helpful.
  • Richard from New Windsor, NY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Unscrewed 4 screws,pulled off front of machine.Unscrewed 2 screws holding coils on,unplugged coils,installed new coils,plugged in coils,reinstalled 2 screws for hold down brace.Reinstalled front cover,plugged dryer into outlet(remember to unplugged dryer before working on it).started up,instant heat,works great.thanks Partselect for helpi ng me out!!!
Was this helpful?
Thank you for voting!
The Dryer stopped working completely.
13 of 18 people found this instruction helpful.
  • Elyse from Chicago, IL
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
I looked up the procedure to remove the switch in a repair book, removed the broken switch. Then I reconnected the wire leads, put the part in and closed everything up. The part arrived so quickly and there were even instructions with the part which made the repair go so easily.
Was this helpful?
Thank you for voting!
dryer would stall and the motor would hum before tripping circuit breaker
11 of 12 people found this instruction helpful.
  • Charles from Placentia, CA
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set, Wrench (Adjustable)
When the problem first came up, I took the dryer apart without first looking up any instructions. This wasn't difficult, but didn't realize when removing the fan from the motor, there is a square lug as part of the fan hidden by the rear clamp securing the motor. I was able to remove the fan by holding the motor shaft with a crescent wr ench and removing the fan by hand, but was difficult and gloves were necessary in case the fan loosened quickly and my hand came in contact with the sheet metal (very sharp).

I took the motor out and attempted to clean it as it was loaded with dust as was the dryer internals. I tried to lube the motor bearings and appeared to free up, but the sight of metal shavings on the rear bearing seal had me concerned. This ultimely did not work and was trying to buy some time until the new motor arrived.

This is when I looked up the motor part number and found that Parts Select had the part number in stock. I ordered the motor on a Saturday afternoon and got a quick response acknowledging my order. The motor shipped that following Monday from Fresno and arrived on my Southern California doorstep Tuesday. These guys have their act together and are helpful in making the repairs. In my case I did not have to make any adjustments to the wiring or the pulley for my model and replaced the motor the following weekend in about 45 minutes. Since I had the unit apart several times before replacing the motor, the installation went quickly.

The dryer is again working fine for a unit 12 years old and my wife is once again happy that we didn't have to purchase a new dryer.
Was this helpful?
Thank you for voting!
One of the drum support rollers was worn out
13 of 19 people found this instruction helpful.
  • David from Fleetwood, PA
  • Easy
  • 30 - 60 mins
  • Screw drivers, Wrench (Adjustable)
I lifted the top of the dryer and removed the front panel. I removed the drum exposing the drum rollers. I replaced the rollers and reassembled the dryer. The exploded views on the web site made it easy to see what to do.
Was this helpful?
Thank you for voting!
Top of washer wasn't attached to base
10 of 11 people found this instruction helpful.
  • Janel from Las Vegas, NV
  • Easy
  • 30 - 60 mins
  • Screw drivers
First, let me start off by saying - this part wouldn't normally break. Because it's a stackable, and my dryer motor went out, the repair company had to move the entire unit from the cubicle. When the repairman tried moving it by using the washer lid ... lets just say he broke the clip. And then we could never get them to come fix the part they broke!

So, I finally ordered the part myself after studying schematics online. I am not a repair person. So, if I could figure this out - anyone can.

Take the middle cover between the washer and dryer off. There are 3 screws holding that panel on. Set the panel and screws aside. There are two "S" shaped clamps at the back. Lift (hard) the front of each one. They will snap free - freeing the whole top of the washing machine. The top has the lid connected. Pull the top towards the front and then rotate it counter-clockwise. It will come right off. This will free up the area the clips go on.

Take the lid completely off to get it out of the way. The clips fit in the holes on the front left and front right. The large square side goes up, and the small side snaps into the hole on the base. Make sure the groove is facing forward for the top cover to slide into. To get the clip to snap into the hole, put the front side down, and push (really hard) on the back side - the side towards the back of the washer. It should snap into place with some pressure.

Now, just put the top cover (with the lid attached) back on, rotate it clockwise, re-clamp it down and replace the middle panel and 3 screws.

Easy, right?
Was this helpful?
Thank you for voting!
Washer stopped working mid cycle restarts after resetting lid
12 of 17 people found this instruction helpful.
  • Eric from West Chester, PA
  • Easy
  • 15 - 30 mins
  • Screw drivers
Repair went well, but my switch only had one contact on the non common end. The new switch had two contacts. One is for operation with lid open and one for lid closed. Make sure to connect to the lid closed contact and the common on the other end and leave the lid open contact unused.
Was this helpful?
Thank you for voting!
All Instructions for the 110894
61 - 75 of 949