110887 Kenmore - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
noisy drum
29 of 40 people
found this instruction helpful.
-
Jeff from Mesa, AZ
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
the job would have gone faster if the right parts had been sent in the first place. I would have never paid for two day shipping. In the repair, I removed the rear panel, clipped the plastic triangle holding the bearing, installed the new bearing and new clip.
Was this helpful?
Thank you for voting!
Lid closes, switch wouldn't turn on machine.
31 of 47 people
found this instruction helpful.
-
Kenneth from Wilmington, IL
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers, Socket set
Used toothpick for a year to push switch acctuator far enough to engage switch. Broke my foot and found time to order part thru PartSelect. Went from cast to boot and received part 2 days after ordered. Had difficulty with foot and getting to switch. Went back into PartSelect and figured out how to dis-assemmble panels thru the diagrams.
... Read more
Time on my job doesn't, just that their service and expertise that is available to everyone is there to use. Broken bones or not, I will always get my parts and advice from PartSelect. Thanks to PartSelect.
Read less
Was this helpful?
Thank you for voting!
craked blower motor
63 of 144 people
found this instruction helpful.
-
joe from cheswick, PA
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
somthing fell down in the blower motor compartment and busted up the bloewr motor fan,and was making noise and out of balance.i changed the blower motor and runs like a charme
Was this helpful?
Thank you for voting!
The spin gear was striped.
25 of 31 people
found this instruction helpful.
-
Aaron from Lake Mills, WI
- A Bit Difficult
- 1- 2 hours
-
Pliers, Socket set
I had to take the motor and transmission out. They are one piece. Removed the clutch, take off trans. cover, remove a snap ring, take the striped gear off, and put the new one on. Then put put everything back on the way it came off.
Was this helpful?
Thank you for voting!
Dryer would quit before the end of the cycle
24 of 28 people
found this instruction helpful.
-
Ernest from Beaumont, TX
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
My wife reported that the dryer was not working. I checked it and it seemed to work fine. This went on for about a month or two. Every time I checked it, it started just fine.
Well, she threatened to go buy a new dryer, I took her more seriously. I thought perhaps a thermal protection was the cause. But when I dug into it, ... Read more I learned that when those trip out, they are permanent (have to be replaced).
I finally noticed loud humming sound the motor made at start-up, when it failed to start turning on one occasion and eventually tripped out the motors thermal protection.
I ordered the new drive motor form PartSelect.com.
Replacing the motor was fairly easy if you like to take stuff apart. One thing that I had not anticipated was that the two foam gaskets on the exhaust duct were dry rotted. I went to my local part supplier to get them. They did not have them in stock. :( While I was there, I asked how much the motor was, they wanted $50 more than PartSelect.com :D
I put it back together without the new gaskets, and it runs like new. I ordered the gaskets from PartSelect and will add them when they arrive.
My wife is happy again, she can bust out the laundry in one day; it had been taking here all weekend.
I learned to take her at her word.
Well, she threatened to go buy a new dryer, I took her more seriously. I thought perhaps a thermal protection was the cause. But when I dug into it, ... Read more I learned that when those trip out, they are permanent (have to be replaced).
I finally noticed loud humming sound the motor made at start-up, when it failed to start turning on one occasion and eventually tripped out the motors thermal protection.
I ordered the new drive motor form PartSelect.com.
Replacing the motor was fairly easy if you like to take stuff apart. One thing that I had not anticipated was that the two foam gaskets on the exhaust duct were dry rotted. I went to my local part supplier to get them. They did not have them in stock. :( While I was there, I asked how much the motor was, they wanted $50 more than PartSelect.com :D
I put it back together without the new gaskets, and it runs like new. I ordered the gaskets from PartSelect and will add them when they arrive.
My wife is happy again, she can bust out the laundry in one day; it had been taking here all weekend.
I learned to take her at her word.
Read less
Was this helpful?
Thank you for voting!
The dryer was running and it quit, just stopped. A friend looked at it and thought it was this switch. I purchased the switch and he installed and it still did not work.
24 of 28 people
found this instruction helpful.
-
Debbie from Mooresville,, IN
- Easy
- Less than 15 mins
-
Nutdriver
No, if that had of been the problem, it would have worked. However, I called a service man out to look at it. It was a fuse that does not look like a fuse. I had the system already torn apart and cleaned. The service took a meter and checked the fuse ( that did not look like a fuse) and it was bad. It cost 14.00 for the fuse, it took less
... Read more
than 5 minutes for installation and the service fee was $65.00. My advise, get a meter, check everything yourself, and only purchase what you need.
Read less
Was this helpful?
Thank you for voting!
washer wouldnt agitate or spinn but would drain?
22 of 22 people
found this instruction helpful.
-
lester from Belleville, WI
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
So i replaced the above parts pulled gearbox put new oil in all looked good but when i tryed it filled started spinning for a few sec.then quit again?was makeing a clicking sound so i layed on the floor and the drive coupling was spinning so i took the water pump off and it started agitating and spinning. found about a 6 in.thin piece of
... Read more
wire in it, dont know where it came from but installed a new pump and it works like a new one !!!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Agitator was locked up
24 of 28 people
found this instruction helpful.
-
Roger from Palmyra, IN
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
I had a little difficulty at first, trying to remove the back of the unit. I then figured out that the repair was to be made by leaning the washer back and removing it from underneath. That became really easy as the bottom is open.I had to remove one nut and then the agitator from inside, then tilt the machine back, disconnect the two ho
... Read more
ses from the pump, remove three bolts and lower the motor/ transmission assembly. Then I had to disconnect the motor from the pump ( with two snap on clips) and remove the broken plastic coupling. The new coupling had a metal insert that seems to make it stronger than the original piece.I then just reversed the procedure to put it together again and it worked fine. The part was shipped immediately and I got it sooner than I expected so I greatly appreciate that. Overall it went well, and by the way, it was my daughters washer and she was happy as well.Thanks, Roger
Read less
Was this helpful?
Thank you for voting!
Motor was working and rotating lower portion of agitator, but the top was not spinning.
22 of 24 people
found this instruction helpful.
-
Brad from Boise, ID
- A Bit Difficult
- 30 - 60 mins
-
Socket set
1. Remove the fabric softener receptacle
2. Remove the plastic dome shaped separator with a rubber o-ring around it (directly beneath fabris softener receptacle)
3. There is an 11mm bolt right in the center. Use socket wrench to remove bolt.
4. Remove agitator from washign machine.
5. Separate ... Read more top half of agitator from bottom half (this was the most difficult part for me; unlike others who have described this repair, mine would not simply pull apart; I spent quite a while trying to pry up the white plastic clips extending from the bottom piece through the clear plastic piece that covers the "dog teeth" that make the top piece agitate)
6. Once apart, replace worn "dog teeth" with new dog teeth.
7. Put back together in reverse order.
2. Remove the plastic dome shaped separator with a rubber o-ring around it (directly beneath fabris softener receptacle)
3. There is an 11mm bolt right in the center. Use socket wrench to remove bolt.
4. Remove agitator from washign machine.
5. Separate ... Read more top half of agitator from bottom half (this was the most difficult part for me; unlike others who have described this repair, mine would not simply pull apart; I spent quite a while trying to pry up the white plastic clips extending from the bottom piece through the clear plastic piece that covers the "dog teeth" that make the top piece agitate)
6. Once apart, replace worn "dog teeth" with new dog teeth.
7. Put back together in reverse order.
Read less
Was this helpful?
Thank you for voting!
Washer stopped before rinse cycle
74 of 180 people
found this instruction helpful.
-
Pam from San Diego, CA
- Easy
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
My husband actually did the repairs all I know is he removed the lid, removed the old switch and put in the new one. My washer works now and thats all I care about. I thank you for having the part and at a reasonable cost we were able to repair our washer considering it is twin stackable and is over 10 years old.
Thanks again!!!!
Thanks again!!!!
Was this helpful?
Thank you for voting!
In the spin cycle, drum would'nt spin unless assisted
22 of 24 people
found this instruction helpful.
-
ANTHONY from NY, NY
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
First off unplug the machine then turned off H/C water supply and removed hoses, laid the machine on its side, removed 3 motor supp. bolts, loosened drum pulled out shaft and clutch assembly was right there. Also replaced coupling while it was apart. And to think, a svce company wanted 179.00 just to walk in my door and diagnose the pblm.
... Read more
Then, parts and labor were extra. Thanks for the help/advice, piece of cake!!!!!!!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Tub did not center and seal was hanging out of tub
22 of 25 people
found this instruction helpful.
-
James from Nelsonville, OH
- Easy
- 1- 2 hours
-
Pliers, Socket set
Laid washer on front side and removed top spring, then lifted the tub assembly to replace the right side spring, the one behind the motor was the hardest, I lifted the tub then removed the spring bracket at the tub with pliers and a socket. The top seal all I had to do was take the 4 screws that hold the top on (it takes a long extension)
... Read more
then sit it bak up and I lifted the top up to give me enough room to unsnap the top piece of the tub, cleaned it up put seal in. The parts fit perfitlt and real fast shipping, I bookmarked the site and will buy from again. JIM
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Cog stripped causing agitator to not turn
22 of 25 people
found this instruction helpful.
-
Vicki from Houston, TX
- Easy
- Less than 15 mins
-
Screw drivers, Wrench set
Removed top cap on agitator w/ flathead screwdriver. Removed protective cap over bolt and cog housing shaft. Used 7/16 deep socket w/ extension to remove bolt. Removed housing where stripped cogs were located. Cogs seated loosely in shaft housing no tools required to remove cogs. Replaced cogs in housing, made sure everything was lined co
... Read more
rrectly. re-inserted housing into shaft. ,screwed bolt, replaced caps and works like new.
Read less
Was this helpful?
Thank you for voting!
In the middle of changing loads there was snapping and sound and drum stopped turning.
24 of 32 people
found this instruction helpful.
-
William from Glen Burnie, MD
- A Bit Difficult
- 1- 2 hours
-
Socket set
I was hopeful it was the belt. But, I had no idea how to get to it. I used the model no. and looked on line for pats and schematics. That gave me a sense of what to do. I started at the rear and removed the back panel. It was like peeling an onion because then, I wasn't sure what to remove next. So I just kept removing nut head screws
... Read more
until eventually I had loosened the sides, removed the top and discovered the front lifted up and off (no screwed attachment.) There's grounding wire that must be detached. Don't forget to re-attach. Without proper grounding you could be electocuted! I was careful to remember how it was attached. To get to the pulley, which is on the front, I had to remove the drum. I found the snapped belt. The pulley is held in place by tension from the belt so, once the belt goes the pulley detaches. I tried to find the belt locally the following week but was unsuccessful. I found the part on-line and had it in four days. It was tricky getting the belt and pulley in place. I persevered.
The parts ( I replaced the fliter that needed replacement for years too) came with installation instructions. Its possible I did not have to disassemble as much as I did. Oh well! Although I'm fairly mechanical, I'm still pretty proud to have been able to do it and save the cost of a repairman.
The parts ( I replaced the fliter that needed replacement for years too) came with installation instructions. Its possible I did not have to disassemble as much as I did. Oh well! Although I'm fairly mechanical, I'm still pretty proud to have been able to do it and save the cost of a repairman.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Push start and the motor would hum.
22 of 26 people
found this instruction helpful.
-
Doug from Manitowoc, WI
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
**** Remove power cord from the wall****
As said earlier, you will need to lift the top. Drop the two screws holding the lint shoot and pop the top by sliding a screw driver into the corner on the front. Lif tthe top and rest against the wall behid the unit. remove the two (4 total) screws at the top and bottom of the front doo ... Read more r assembly.
Place sometin under the front portion of the drum. At this point you'll see the need to clean everything! :) Slide the belt off and around the drum, (take note of the routing it takes.) Remove the drum by gently pulling it towards you. Set it aside. Clean more. :) (It is nice to have a vacuum handy.) At this point you really need to get to the rear of the system. So I tipped the top back down, and spun it around. Removed the rear panel and cleaned some more. (15 years of a lot of lint in there!) Then you'll need to remove the rear cover on the left side, covering the blower impeller. Get read for a whole lot of debris. Vacuum again. So now you have the motor exposed in the front and rear. You need to remove the impeller by turning that clockwise to loosen it. The trick is holding the shaft in place from the front at the same time. I used an old rag and wedged it into the impeller edges and worked it around until it jamed up. Once the rag was wedged pretty good, I went back to the front spun the shaft. Then you can remove the impeller by hand. Vacuum more. You may get by without having to remove the lint shoot completely, but I did just to clean it up more. I did have to remove two screws in the upper corner near the top of the lint shoot. (Basically the hold the back in place.) I took a few notes at this point about the wiring harness. Used a heavier screw driver (standard), You can push down on the clips that hold the old motor in place. Then work it out the front. Clean more. The new motor is not an exact replacement slightly differnt but the instructions with it were ok. Follow them for the correct wiring. You will need to remove one wire and cut and recrimp a spade lug or two. I used ty-wraps to secure the lines back in place. Look closely at the diagrams and make sure you set the motor down in the same direction the instructions say, if you twist it slightly it will sorta lock in place where it needs to be. Re-install the hold down clips to the front and rear of the motor. Clean up your impeller, and reinstall it too. Then basically reassemble the dryer...tracing your steps backwards. This isn't really difficult, it just takes time and as you can see, you will/should clean as you go !
As said earlier, you will need to lift the top. Drop the two screws holding the lint shoot and pop the top by sliding a screw driver into the corner on the front. Lif tthe top and rest against the wall behid the unit. remove the two (4 total) screws at the top and bottom of the front doo ... Read more r assembly.
Place sometin under the front portion of the drum. At this point you'll see the need to clean everything! :) Slide the belt off and around the drum, (take note of the routing it takes.) Remove the drum by gently pulling it towards you. Set it aside. Clean more. :) (It is nice to have a vacuum handy.) At this point you really need to get to the rear of the system. So I tipped the top back down, and spun it around. Removed the rear panel and cleaned some more. (15 years of a lot of lint in there!) Then you'll need to remove the rear cover on the left side, covering the blower impeller. Get read for a whole lot of debris. Vacuum again. So now you have the motor exposed in the front and rear. You need to remove the impeller by turning that clockwise to loosen it. The trick is holding the shaft in place from the front at the same time. I used an old rag and wedged it into the impeller edges and worked it around until it jamed up. Once the rag was wedged pretty good, I went back to the front spun the shaft. Then you can remove the impeller by hand. Vacuum more. You may get by without having to remove the lint shoot completely, but I did just to clean it up more. I did have to remove two screws in the upper corner near the top of the lint shoot. (Basically the hold the back in place.) I took a few notes at this point about the wiring harness. Used a heavier screw driver (standard), You can push down on the clips that hold the old motor in place. Then work it out the front. Clean more. The new motor is not an exact replacement slightly differnt but the instructions with it were ok. Follow them for the correct wiring. You will need to remove one wire and cut and recrimp a spade lug or two. I used ty-wraps to secure the lines back in place. Look closely at the diagrams and make sure you set the motor down in the same direction the instructions say, if you twist it slightly it will sorta lock in place where it needs to be. Re-install the hold down clips to the front and rear of the motor. Clean up your impeller, and reinstall it too. Then basically reassemble the dryer...tracing your steps backwards. This isn't really difficult, it just takes time and as you can see, you will/should clean as you go !
Read less
Was this helpful?
Thank you for voting!