110887 Kenmore - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer motor runs,drum turns but no heat.
30 of 33 people
found this instruction helpful.
-
Arron from El Reno, OK
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Removed the back of the dryer. Used a multimeter set to read Ohms to check each Thermal cut-off switch. Each one read with continuity and some resistance. The one that was bad read open. So i replaced this one and the other one that came in the kit since i already paid for both.Then i replaced the back ran the dryer and it worked great.
Was this helpful?
Thank you for voting!
Top door catch assembly had broken
29 of 31 people
found this instruction helpful.
-
tony from prineville, OR
- Easy
- Less than 15 mins
-
Screw drivers
It was so easy, that my wife did it the day we got the part before I got home from work. She wedged it out with a flat head screw driver and then pushed the new door catch assembly in with her thumb. Pretty simple, thanks for having parts like this available to the public!
Was this helpful?
Thank you for voting!
push to start switch was not working
33 of 43 people
found this instruction helpful.
-
Grace from New Smyrna Beach, FL
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers, Screw drivers
Removed the old one and installed the new one! What impressed me the most was the amount of time for delivery, one day! Actually it came before 24 hrs!!! Very impressive! I would highly recommend this company!!!
Was this helpful?
Thank you for voting!
Dryer door catch broke
35 of 49 people
found this instruction helpful.
-
Bill from Houston, TX
- Really Easy
- Less than 15 mins
The old catch on my dryer door was gone and I was keeping the door closed using tape. I ordered the part and it arrived with no hassles in about 5 days. The repair was too easy. I just popped the new catch in place. It took all of about 30 seconds to complete using no tools. I wish all home repairs were this easy.
Was this helpful?
Thank you for voting!
Washer would fill/empty but would not agitate nor spin
30 of 35 people
found this instruction helpful.
-
Ted from SOUTH MILWAUKEE, WI
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
Unplugged power cord and disconnected water lines; note which is hot/cold. Washer was then tipped on its front. Discharge hose was disconnected. Washer was then rolled over onto its back as this would put the pump on top for much easier removal.
Pried off two clips attaching pump on motor using a flathead screwdriver. The r ... Read more ear clip was done by touch. Unplugged wiring plug from motor. Using an adjustable wrench (socket set would have worked better), remove two screws holding 2nd set of clips attaching motor on transmission. Then pried off clips.
Removed old coupling from transmission shaft and motor shaft, plus middle 6 hole widget thingy.
Installed new parts on transmission shaft and motor shaft with fingers pointing towards each other. Using a small hammer, tapped the parts onto each shaft. Placed 6 hole widget thingy on the transmission part, and then rotated motor so motor part would fit in remaining three holes.
Replaced clips to hold motor on transmission and reinstalled screws holding clips.
IMPORTANT: Replace motor wire now. I forgot to do this and after the tub was filled with water, realized that, and since the pump was also disconnected, could not get the water out. Had to get wife to hold washer up while I crawled underneath to reattach motor wire. Learn from my mistake!
Attach pump onto motor and replace clips. Double check everything is back in place.
Roll washer onto front side. Attach discharge hose. Tip washer back upright. Reconnect water. Reposition discharge hose and plug washer into power.
First try it smelled like something plastic was burning, but I think that was the old part shavings getting ground away.
Pried off two clips attaching pump on motor using a flathead screwdriver. The r ... Read more ear clip was done by touch. Unplugged wiring plug from motor. Using an adjustable wrench (socket set would have worked better), remove two screws holding 2nd set of clips attaching motor on transmission. Then pried off clips.
Removed old coupling from transmission shaft and motor shaft, plus middle 6 hole widget thingy.
Installed new parts on transmission shaft and motor shaft with fingers pointing towards each other. Using a small hammer, tapped the parts onto each shaft. Placed 6 hole widget thingy on the transmission part, and then rotated motor so motor part would fit in remaining three holes.
Replaced clips to hold motor on transmission and reinstalled screws holding clips.
IMPORTANT: Replace motor wire now. I forgot to do this and after the tub was filled with water, realized that, and since the pump was also disconnected, could not get the water out. Had to get wife to hold washer up while I crawled underneath to reattach motor wire. Learn from my mistake!
Attach pump onto motor and replace clips. Double check everything is back in place.
Roll washer onto front side. Attach discharge hose. Tip washer back upright. Reconnect water. Reposition discharge hose and plug washer into power.
First try it smelled like something plastic was burning, but I think that was the old part shavings getting ground away.
Read less
Was this helpful?
Thank you for voting!
A high pitched squeal when drum was rolling.
28 of 30 people
found this instruction helpful.
-
Robert from GOODRICH, TX
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
First my son and I moved the dryer to the garage as we believed there would be a lot of lint possible during disassembly. Used a flat head screwdriver to pop the top from dryer housing. Then removing 2 nuts to facilitate the removal of the front of the dryer. The drum was able to be removed to diagnose the offending drum roller wheel.
... Read more
The drum roller wheel has experienced a failure as it had melted off of the metal spacer. Removing it and replacing with the new one was pretty easy. We then used a shop vac and an air hose to clean out all the lint, coins, paper clips and lost jewelry. Surprisingly there was not a single sock in there. Put it all back together in reverse order and plugged it in and now spins like a dream.
Read less
Was this helpful?
Thank you for voting!
dryer ran, but no heat at all.
27 of 29 people
found this instruction helpful.
-
Christopher from Easthampton, MA
- Really Easy
- 15 - 30 mins
-
Nutdriver
I removed the hex screws from the fuse, unhooked the wire contacts and replaced with new fuse. I then plugged in the dryer and tried it. It worked!!
I then went on to unplug appliance again, replace the thermostats (while I had the back open and in case bad thermostats could have lead to fuse going bad)... roughly the same process as ... Read more fuse. We've been enjoying dry warm clothes ever since, and I'm sure that it is running more consistently than it had been for the past several months. I am a repair GOD.
I then went on to unplug appliance again, replace the thermostats (while I had the back open and in case bad thermostats could have lead to fuse going bad)... roughly the same process as ... Read more fuse. We've been enjoying dry warm clothes ever since, and I'm sure that it is running more consistently than it had been for the past several months. I am a repair GOD.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Severe water leak
27 of 29 people
found this instruction helpful.
-
Noel from Pollock, ID
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
1) Unplugged electrical cord
2) Removed hot/cold water hoses
3) Took drain hose from laundry room recepatcle
4) Moved washing machine to area where I could lay it down on its back (very important for easy fix)
5) Found (easy accessible in my case) water pump with an inlet and outlet water hose held on with spring clamp ... Read more s.
6) Removed each of the two clamps with pliers and each hose by twisting loose
7) Remove two metal clips holding pump to motor housing
8) Slide pump off shaft - removal is finished!
9) Reversed process for installation, making sure to gently align pump housing when the pump is aligned with the shaft
[probably took less than 15 minutes]
2) Removed hot/cold water hoses
3) Took drain hose from laundry room recepatcle
4) Moved washing machine to area where I could lay it down on its back (very important for easy fix)
5) Found (easy accessible in my case) water pump with an inlet and outlet water hose held on with spring clamp ... Read more s.
6) Removed each of the two clamps with pliers and each hose by twisting loose
7) Remove two metal clips holding pump to motor housing
8) Slide pump off shaft - removal is finished!
9) Reversed process for installation, making sure to gently align pump housing when the pump is aligned with the shaft
[probably took less than 15 minutes]
Read less
Was this helpful?
Thank you for voting!
had to replace the motor
31 of 43 people
found this instruction helpful.
-
charles from parker, CO
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Screw drivers
Follow the advice given in the partsselect website. However, while removing the blower, my hand slipped into the housing and cut my thumb. Connected the wires to the junction box on the motor but didn't realize that the contacts would hit the drum when reinstalled. The original junction box was at a 90 degree rotation relative to the n
... Read more
ew box. When trying to test the breaker tripped. Using the multitester I found out that I burned out the thermal fuse, and froze the door switch. I replace both those parts and started the dryer and could hear a grinding sound. Inspection revealed that the housing of the motor was rubbing against the drum. Removing the drum yet again, I rotated the housing and replaced the drum. The dryer was finally working well.
Read less
Was this helpful?
Thank you for voting!
Dryer not spinning
33 of 49 people
found this instruction helpful.
-
john from goldsboro, NC
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
I took off the front panel via 2 screws on the inside of the dryer with the top panel in the maintenance position. Pulled out the tub(cut my hand pretty bad in the process but continued). Did some cleaning and I had to google how the belt tensioner goes into place. Rather difficult on your own i held the belt and placed the tub back into
... Read more
place while placing the belt around the tub putting it in the correct area. thats pretty much it and began reinstalling the parts i had removed.. easy fix now that i have done it once. This is all after my landlords said they werent replacing it and just to have this one hauled off, so all in all i have a 26 dollar dryer now:)
Read less
Was this helpful?
Thank you for voting!
Drier would not heat
26 of 29 people
found this instruction helpful.
-
Jason from Birmingham, AL
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Wife said the drier was not heating. I looked on the internet and found Parts Select. Followed the instructions to test the heating element, thermal cut-offs, and thermostat. This is really easy, you just touch the terminals with the voltage meter to see which ones are not transmitting current (with the drier unplugged). One of the t
... Read more
hermal cut-offs was not transmitting current so I ordered the part Sunday night and had it by Wednesday morning and put it on it about five minutes. Steps:
1. Unplug drier
2. Unscrew back of drier
3. Unplug wires from terminals of the parts shown in Parts Select instructions (one at a time)
4. Get a basic voltage meter (I bought a cheap one at the big box store)
5. Test terminals (touch the red terminal on the voltage meter to one side, black to the other)
6. If the needle moves to the other side, the part is OK, if not order the part and replace.
1. Unplug drier
2. Unscrew back of drier
3. Unplug wires from terminals of the parts shown in Parts Select instructions (one at a time)
4. Get a basic voltage meter (I bought a cheap one at the big box store)
5. Test terminals (touch the red terminal on the voltage meter to one side, black to the other)
6. If the needle moves to the other side, the part is OK, if not order the part and replace.
Read less
Was this helpful?
Thank you for voting!
dryer ran but no heat
34 of 53 people
found this instruction helpful.
-
Mary from Red Bud, IL
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers, Socket set, Wrench set
I removed the dryer rear upper cover to expose the start and cycle selection knob. My wiring diagram was in there. I removed the wiring on the rear of the cycle selection knob (timer assembly) locations were marked on the device. I ohmed the switch contacts for the heat circuit and had an open circuit through out the full rotation of the
... Read more
knob. I removed the 2 screws on the back of the timer assembly and the burnt contacts fell out. I removed the knob and 2 mounting screws and the device was out to retrieve my part numbers.
Read less
Was this helpful?
Thank you for voting!
water overflowing when filling
34 of 54 people
found this instruction helpful.
-
Marni from Buhl, ID
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I ordered the parts at a minimal cost compared to the repairman's quote, they arrived in 3 days. I used the laptop and put it right next to where I was working so that I could follow the directions step-by-step. The instructions were easy to follow and showed you right what to do so I never had any questions. My washer had a slightly d
... Read more
ifferent configuration but I figured it out. Replacing the parts was simple, take one off, put the other on. Putting the washer front back on was a little tricky, I had to have my daughter help me hold it in place while I wiggled it around to make sure it was just right before I screwed it back together. It was easier than I thought it would be. I told my husband I loved the internet, I would never have been able to do this job without the instructional video. Thanks PartsSelect!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer would not heat up; blow only air
26 of 30 people
found this instruction helpful.
-
William from Sacramento, CA
- A Bit Difficult
- 1- 2 hours
-
Nutdriver
I replaced the thermal cut off kit, and the dryer now had heat. Three days later, no heat; the thermal fuse also did not have continuity. Read on-line that overheating was the most likely cause. So, I checked the exhaust duct for blockage, but it was clear. Then, I removed the exhaust canister at the back of dryer; the entire bottom wa
... Read more
s filled with lint the size of a softball. The lint was heating up, and when it got too hot, it blew the thermal cut off. Cleaned out the lint, replaced the thermal cut off, and now it's fine. Moral of the story: Remove the lint canister and clean it.
Read less
Was this helpful?
Thank you for voting!
Water constantly dripped into washer when it was off.
24 of 25 people
found this instruction helpful.
-
MARK from MARION, MA
- Really Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
Turned off water and pulled power plug, Then unscrewed hot and cold hoses from washer.
I took off the top control by undoing the 2 screws in front and then the two screws on the back plastic latches. Mover it forware and took off the 2 screws on the bottom of the back which came up and off easily. Undid the two screws holding the Wat ... Read more er valve to the back and undid the water outlet tube and the wireing. Replaced with new valve and reattached tubing and wires. Screwed back on and reattached controls.
Actually was very easy even without repair manual to the washing machine.
I took off the top control by undoing the 2 screws in front and then the two screws on the back plastic latches. Mover it forware and took off the 2 screws on the bottom of the back which came up and off easily. Undid the two screws holding the Wat ... Read more er valve to the back and undid the water outlet tube and the wireing. Replaced with new valve and reattached tubing and wires. Screwed back on and reattached controls.
Actually was very easy even without repair manual to the washing machine.
Read less
Was this helpful?
Thank you for voting!