1108739 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer would not activate unless jarred by striking with the hand.
6 of 8 people
found this instruction helpful.
-
DAVID from AKRON, OH
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Socket set
Investigated inside control panel for loose wires or parts. Removed back of control panel and back of dryer and used a vacuum to remove lint from every possible contact. Problem not fixed.
Lifted top of dryer and cleaned inside. Struck door close switch with a screw driver and dryer started every time. Replaced switch.
... Read more />
Works every time. This is the 3rd repair in over 20 years. Each time the dryer works as though new.
Lifted top of dryer and cleaned inside. Struck door close switch with a screw driver and dryer started every time. Replaced switch.
... Read more />
Works every time. This is the 3rd repair in over 20 years. Each time the dryer works as though new.
Read less
Was this helpful?
Thank you for voting!
Motor was bad
5 of 5 people
found this instruction helpful.
-
Michael from CLIFTON HTS, PA
- Really Easy
- 30 - 60 mins
I have not received the parts yet waiting on the motor, can’t put the blower fan in without the motor, ordered it , Jan 23rd, still no motor, have to go to laundry mat, have you ever had to do that with 7kids, and you and your wife’s laundry, probably not, because you would have had your motor by now. Maybe you can help me with the part s
... Read more
o I can redo a testimonial here for you. 19 days and still waiting
Read less
Was this helpful?
Thank you for voting!
Poor drying and took excessive amount of time to complete partially dried loads
5 of 5 people
found this instruction helpful.
-
Stephen from LOUISVILLE, KY
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Took back cover off. Cleaned out the lint that had built up inside the dryer. Replaced the lint trap housing and lint chute seals. Also replaced the drying vent hose. Works great now.
Other Parts Used:
Was this helpful?
Thank you for voting!
light bulb in water ice freezer door went bad
8 of 14 people
found this instruction helpful.
-
Carl from RIVERSIDE, CA
- Very Difficult
- More than 2 hours
-
Screw drivers
I didn't. Don't know how to get to light bulb to change it for this specific model
Was this helpful?
Thank you for voting!
Loud squeeking.
6 of 8 people
found this instruction helpful.
-
John from Alton, IL
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Wrench set
I ordered the belt idler pully and drum support rollers and after watching the video on Parts Select web page, changed the parts. It could be done by one person, however having a second person to help with the drum installation worked great. I discovered the motor bearing on the front side of the motor was the source of the squeek. I d
... Read more
isassembled the dryer again and removed the motor. After ordering a motor the installation and reassembly went smoothly. The parts came in two days of placing the orders and virtually new parts in the dryer makes it seem like a new machine.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
seal came of dryer door
8 of 15 people
found this instruction helpful.
-
alice from wickliffe, OH
- Really Easy
- Less than 15 mins
romoved from pkg. and fit it to the door. no tools needed. best of all the part came in 24 hrs and was fixed with out delay of waiting from a store that was out of our area. great costumer service!!!!!
Was this helpful?
Thank you for voting!
incessantly annoyingly squeaky dryer
5 of 6 people
found this instruction helpful.
-
Douglas from Tiburon, CA
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Socket set
Take out 2 philips screws in lint trap holder on top. Use flat screwdriver to pry up front left and right of dryer top near outside edges and tilt up out of the way. Remove 2 push-on AC connectors on door switch and remove plastic clip holding wires to dryer's front top metal edge. Remove (2) 5/16" sheet metal screw on inside top left an
... Read more
d right edges to free up front panel. Lift front panel about an inch and it'll then pull off. It helps to have a second person to help hold or remove the drum at this point. It took 3 times for me to guess right on the squeak. First time I replaced the belt, second time I replaced these rollers, third and final time I replaced the idler pulley, the shaft of which had worn completely off so clearly i can't figure out how we didn't see (or hear) it the first two times! Dri-Slide lube helped stop the squeaking the first two times, but it always returned until this time, now I have a thoroughly rebuilt dryer for the next generation! (PS vacuum out the bottom of the dryer while it's open to remove both lint and greasy roller shavings - do this FIRST and you'll have cleaner hands & clothes!)
Read less
Was this helpful?
Thank you for voting!
drum wouldn't turn
5 of 6 people
found this instruction helpful.
-
Lisa from Woodstock, GA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Actually, I was the handy man. First I removed the front panel. Then I used 3 - 2x4s to hold up the drum. Then I slipped the belt around the center of the drum ,motor,and around the pulley at the bottom of the dryer. That was it, and then I put it back together. My wife was amazed and proud that I did it without calling for help! No Pro
... Read more
blem!
Read less
Was this helpful?
Thank you for voting!
Brown Lines on Clean Clothes coming out of Dryer
5 of 6 people
found this instruction helpful.
-
John from Semmes, AL
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Removed the top and front panel, removed the dryer drum. Removed the worn out rear drum seal. I scraped and sanded the old glue residue from the rear of the drum. I used "0000" steel wool to clean the "brown seal residue" from the rear panel where the new seal on the drum would rub/seal against the rear panel. I used spring clamps to
... Read more
hold the seal in place prior to appling the glue. The glue was applied to the drum/seal and allowed to dry 30-45 min. I replaced the front drum seal (some of the other discussions in your forum had good hints on replacing this seal, better than the printed instructions), also replaced the belt and applied a light amout of lubrication (3 in 1 oil) to the idler pulley and the drum rollers. The dryer runs smoothly and quietly and most importantly no more brown streaks on clean clothes.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
The dryer was squeaking and would not heat at all.
7 of 12 people
found this instruction helpful.
-
Steven from Oxnard, CA
- Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
The first thing I did was call my friend Donnie who manages some apartment buildings and who is always complaining about fixing things and getting the right parts to fix things. He told me what to order from PartsSelect and when the parts got here I called him up and he did the repair work.
He was reluctant to do the work at f ... Read more irst but after he found out I had ordered the parts from PartsSelect he was happy to do the work. "Their parts are always right and they always work," was what he said after he had my dryer working just like new. So if you know nothing about fixing things and buying parts just call PartsSelect and you will be fine. Just ask my friend Donnie!!!
He was reluctant to do the work at f ... Read more irst but after he found out I had ordered the parts from PartsSelect he was happy to do the work. "Their parts are always right and they always work," was what he said after he had my dryer working just like new. So if you know nothing about fixing things and buying parts just call PartsSelect and you will be fine. Just ask my friend Donnie!!!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Front seal was ripped.
5 of 6 people
found this instruction helpful.
-
Neil from Southgate, MI
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers
Step one: UNPLUG THE 220V LINE!
Removed the 2 screws on top under the lint door then flipped up the top. Next I unclipped the wire harness at the front and disconnected the 2 wires to the door switch and flipped the harness out of the way. Then I popped off the kick panel. Next, I removed the (4) 9mm screws holding the fron ... Read more t panel on. The 2 lower screws only need to be loosened and the panel lifted off. Note the location of the door springs at the bottom. These springs can be reinstalled easily through the kick panel after you reinstall the front panel.
Next I removed the remnants of the old seal from the front panel but left the 3 plastic clips in place. The seal wraps around the perimeter of the panel and is held in place by the lip of the opening. The extra flap is then folded back so that the folded edge is toward the dryer drum and away from the front of the panel. The sketch in the instructions is not helpful!
Next, reinstall the front panel. As you set it onto the lower screws, you may need to lift the drum slightly to fit the panel into the drum opening. Tighten the 4 screws then reattach the 2 door springs. Test the operation by turning the drum counterclockwise by hand. Check to make sure the rear seal has not been displaced or damaged. That seal is actually glued into place. If it turns smoothly, snap the kick panel back on and reinstall the wire harness. Flip down the top and reinstall the 2 screws at the lint tray on top. Plug it in and give it a spin!.
Note, While you have it open, you'll want to use your shop vac and clean all the lint and pocket change out of the machine. You might as well take off the back panel and clean up in there and in the vent pipe too.
I didn't know if I needed a new belt but ordered one anyway. The old one turned out to be pretty well shot. After I had the front panel removed, replacing the belt is very simple. There is an idler pulley underneath that is under tension. Just push on the idler until the belt is loose. Switch the new one into place and you are done.
Removed the 2 screws on top under the lint door then flipped up the top. Next I unclipped the wire harness at the front and disconnected the 2 wires to the door switch and flipped the harness out of the way. Then I popped off the kick panel. Next, I removed the (4) 9mm screws holding the fron ... Read more t panel on. The 2 lower screws only need to be loosened and the panel lifted off. Note the location of the door springs at the bottom. These springs can be reinstalled easily through the kick panel after you reinstall the front panel.
Next I removed the remnants of the old seal from the front panel but left the 3 plastic clips in place. The seal wraps around the perimeter of the panel and is held in place by the lip of the opening. The extra flap is then folded back so that the folded edge is toward the dryer drum and away from the front of the panel. The sketch in the instructions is not helpful!
Next, reinstall the front panel. As you set it onto the lower screws, you may need to lift the drum slightly to fit the panel into the drum opening. Tighten the 4 screws then reattach the 2 door springs. Test the operation by turning the drum counterclockwise by hand. Check to make sure the rear seal has not been displaced or damaged. That seal is actually glued into place. If it turns smoothly, snap the kick panel back on and reinstall the wire harness. Flip down the top and reinstall the 2 screws at the lint tray on top. Plug it in and give it a spin!.
Note, While you have it open, you'll want to use your shop vac and clean all the lint and pocket change out of the machine. You might as well take off the back panel and clean up in there and in the vent pipe too.
I didn't know if I needed a new belt but ordered one anyway. The old one turned out to be pretty well shot. After I had the front panel removed, replacing the belt is very simple. There is an idler pulley underneath that is under tension. Just push on the idler until the belt is loose. Switch the new one into place and you are done.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Broken drum belt
4 of 4 people
found this instruction helpful.
-
Michelle from Fort Myers BEach, FL
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I noticed my dryer was heating, but not tumbling. I"m a 53 year old single female, and my dryer I bought used 3 years ago. I had no clue what the problem was. I texted my brother and said, "it heats but doesn't tumble - is it shot?" He texted back "probably the drive belt - pop the top and see." So I popped the top, and sure enough, t
... Read more
he belt was broken. So I googled "diy + dryer + drive belt" and watched a You Tube video. I then drove all over town looking for a belt, and the only place that carried it had closed at noon (saturday). So I googled " appliance parts + dryer and came to this site, ordered the part and it was delivered in two days.
I borrowed a nut driver from my brother, removed the front of the dryer, used a plastic cup to prop up the drum. I put the belt on the drum, being sure to place the ribbed side down, looped through the pulley and onto the motor, removed the cup, put the front back on, dropped the top, replaced the lint trap and the two screws holding that in place, turned the dryer on and voila! All done.
I borrowed a nut driver from my brother, removed the front of the dryer, used a plastic cup to prop up the drum. I put the belt on the drum, being sure to place the ribbed side down, looped through the pulley and onto the motor, removed the cup, put the front back on, dropped the top, replaced the lint trap and the two screws holding that in place, turned the dryer on and voila! All done.
Read less
Was this helpful?
Thank you for voting!
drum roller became lose and seperated from the shaft that supports it. it had to be replaced
5 of 7 people
found this instruction helpful.
-
Dillard C. from Vina, AL
- Easy
- 15 - 30 mins
-
Socket set
remove the front panel, belt [notice the way the belt is fasten] remove the tub, support bracket to the drum roller, and slide the new drum roller on and place the tre ring in the slot. then re-install everything in reverse
Other Parts Used:
Was this helpful?
Thank you for voting!
Broken drive belt
7 of 13 people
found this instruction helpful.
-
Stanley from Flushing, NY
- Easy
- 15 - 30 mins
-
Screw drivers
I received the part I ordered immediately and the included instructions made installation a snap. Thank you for your help. I would not hesitate to order from your company again.
Was this helpful?
Thank you for voting!
No heat...
5 of 7 people
found this instruction helpful.
-
Charles from Long Beach, CA
- Easy
- 30 - 60 mins
-
Socket set
Removed and replaced both the thermostat sensor and the ignitor. Tested thej dryer and it worked. Replaced the front panel and it was good to go.
Was this helpful?
Thank you for voting!